How to Replace Ignition Starter Switch 95-96 GMC K1500
ฝัง
- เผยแพร่เมื่อ 23 ก.พ. 2017
- Buy Now!
New Ignition Starter Switch from 1AAuto.com 1aau.to/ia/1AZIS00005
1A Auto shows you how to repair, install, fix, change or replace a broken, damaged, worn or faulty ignition starter switch. This video is applicable to the 95, 96 Chevy or GMC C/K pickup trucks.
🔧 List of tools used:
• Flat Blade Screwdriver 1aau.to/oapB/1AXAA00013
• 21mm Socket 1aau.to/otc/1AXAA00043
• 7mm Socket 1aau.to/o2B/1AXAA00017
• Side Cutters
• Snap Ring Pliers
• E5 Socket
• T25 Driver 1aau.to/ote/1AXAA00008
• Ratchet 1aau.to/oarb/1AXAA00016
• Wire Ties
• Pick 1aau.to/oiP/1AXAA00037
For More Info visit us at 1aau.to/h/bsn/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video. - ยานยนต์และพาหนะ
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
√ *Do it Yourself*
√ *Save Money*
Excellent presentation! I was an instructor for thirty years and don't believe I ever heard anyone as articulate as you are. There was not a single pause, such as searching for a word and your pace was perfect. You should be a college professor! Our situation is a bit different in that the engine will not turn off, even with the key removed. We disconnected the battery to shut down the engine and, also, the panel lights were remaining illuminated. Best of luck from out here in Idaho and we definitely owe you a beer!
My 1996 K1500 had was not shifting, the Tach/Speedometer quit and the gear indicator was out. Ordered this part and replaced the starter switch and it fixed it all. The video is spot on. A couple things to add. No need to remove the snap ring. While not necessary to remove the steering wheel it really gives you room to work if you do. Also pay attention to the direction he is using the screwdriver to remove the airbag. The E-4 star bit can be found at O'riley auto parts. They are a slender 1/4 inch drive socket set of 5 and will fit to take off the two screws holding the switch on. Disassembly took a few because I had never done it but reassembly only took about 30 minutes. Not that hard to do and will save you money by not having someone else do it.
Great video! Helped me a lot especially with the key cylinder. Skip removing the steering wheel, no need even with airbag(mine has one). Also, if you are patient and careful, you can open the switch and clean the contacts and reassemble. Worked for me and saved $120.
Removing the steering wheel and messing with the airbag is an unnecessary step while replacing the ignition switch. The rest of this video is step-by-step exactly how the process should be done.
I was wondering about that. I replaced the key/tumbler assembly without pulling the wheel so I was going leave it unless necessary on this little job too. I was actually going to comment/inquire about it until I saw your post. Thanks.
Outstanding level of detail and clarity on how to access things that are hard to video. Thanks for a great video!
Just changed mine on my 95 chevy 1500 the part you shipped fit just like the original. Thanks for great service
This video saved my ass! Thank you sooo very much! Got in my truck and all of a sudden no windows, wipers or break lights also radio and climate dead. All fuses good, swapped ig switch and boom all good!
+ken2gill Thank you for the great reply. We love to empower our customers by showing you how-to perform your own auto repairs while installing our high quality auto parts. Have a great day! 1aauto.com
Great video I have done this for years and years professionally turning wrenches and only thing that I stopped at what's the key tumbler sensor other than that I did not take off most of what you did that was the only thing I came to this video for thanks a lot for your help👍👍👍
+GreenBoy at GA Farms Thanks for checking us out. Shop here for high quality auto parts: 1aau.to/m/Shop-1AAuto-c
E-sockets are a must...clock spring snap ring doesn't need removed. I also replaced my steering wheel with a next to new model. Great vid
Very good video ! You're right, you must have an E4 inverted socket to get those 2 screws on the top switch. My old harness had a pinched white wire ,probably my fuel pump hot wire, will see if this fixes it- thanks 1AAUTO !
+Hank Postell Thanks for watching. If any of our viewers needs to make this repair, we carry the auto repair part shown in this video on our website. Here is a link to them www.1aauto.com/ignition-starter-switch/i/1azis00005?TH-cam&CTA+Comment&YwLg3JYOYYA
E4 or e5 inverted torx bit cause discription days e5
Your video's have helped me a few times thanks for the great info you provide
If your having transmission trouble, check fuse 20 in the dash fuse pannel. If theres no power supplied to that fuse then your ignition switch has failed.
+Dan Hammond Thanks for the feedback!
Exactly what I was looking for ! Could not figure out how to get top off! That’s cause u can’t until releasing the ignition switch ! I was about to cut . Glad I didn’t. Thanks so much !
Instead of removing the steering wheel, I opted to remove the Driver side seat. Made it somewhat more comfortable. The E4 deep socket is a must.
I just removed the top and bottom covers. The seat bolts are rusted, live in the Midwest.
Great video, as usual from 1A Auto! It appears they replaced the clock spring in this video but did not detail the work on that part. That is the only reason the wheel and the snap ring on the clock spring would need to be removed.
There's another harness for the switch that also has another snap plug that plus into the top of the ignition that looks exactly the same as this one. I pulled 2 today from the junkyard. Easy peezy after you do it a few times
This Video REALLY HELPED ME. THANKS FOR THE UPLOAD🏆 👏😎
+MrLawrence7777 Thanks for checking us out. Shop here for high quality auto parts: 1aau.to/m/Shop-1AAuto-c
Thank you for the detailed walk-through. You saved me $500. I really appreciate it!!
+Ashe Ketchum Thanks for checking us out! 1AAuto.com
Another great, thorough tutorial. My son’s 98 Silverado keeps poppin’ the “IGN-1” fuse (@fuse box under hood). I’ve inspected the fuse box and the underneath side, no signs of burns or corrosion. Could a faulty ignition switch assembly be the culprit? Or, is there something else I should investigate. Thanks.
Fixed the issue with my truck. Tach was not working, speedo was stuck on 100, check gauges light on, gear indicator out, transmission could only be shifted between 2nd and 3rd manually. Thanks for the video. You WILL need a 4mm female torx socket for the steering wheel part of the switch. Start to finish, took me about 3 hours. I did not remove the steering wheel.
Thanks for the comments and for watching! +Kent Eaton
Would this part help stop the security light on a 1999 Chevy Tahoe from coming on? Or is it the cylinder that needs to be replaced? Been having a issue with security light staying on or even flashing at some point. Have to wait 10 minutes before I can start up...
Plz help
Did you install the retaining clip o nthe steering wheel?
Must the E4 torx be deep style?
I got a 97 single cab , was experiencing issues before I got to the first step. ( Disconnect negative cable on battery) . Barely a quarter turn to loosen the cable I got power. I recommend to anyone experiencing problems to try this first!
Do you need to replace the wiring when just replacing the ignition switch?
Hi on my 97 Chevy c1500 I broke the key censor that goes inside the switch housing. Can I use it with out the censor or is ther a repair for just the small plastic censor
Will a bad ignition switch no engine light to come on? Cause noticed when check enginge light is on it starts just fine
Ok so any help would be appreciated.. my 96 Silverado gets stuck in crank mode while cranking the truck. It cranks up just fine but the key gets stuck in crank mode. I’ve already replaced the ignition key and lock cylinder and door locks with one from 1a auto. I thought that would fox the problem but it didn’t so I was wondering would this ignition switch fix the problem?
I have a stripped bolt down on the wiring harness it moves around freely but the center bolt/nut/screw is not coming out. Any advice?
i have a 95 with no tilt!.... i want to swap in a tilt column. do i have to find a 95 doner? or will a 96 97 or 98 steering column work? the reason i ask is because mine is tbi and 96 97 and 98 are vortec.
I currently have a problem with my 98 Tahoe each time I turn the switch into the run position my ignition 40 fuse blows … could these be the problem? ( starter is new thinking that was the problem I replace it since was giving up) I have no other issue whatsoever….
Thank you great video
Good tutorial me ayudó mucho gracias
+Manuel Arechar Thanks for checking us out! 1AAuto.com
Question: Can a bad ignition switch cause an intermittent problem where the alternator does not charge but vehicle will still crank and start? I have this problem on my truck and neither myself nor 3 mechanics have been able to figure out what's going on. It has new alternator, battery etc...problem still randomly happens, which then causes trans computer to not power and truck is stuck in 1st gear with battery discharging. A friend said ignition switch could be the cause... Fun times.
I have an issue where truck starts then shuts off throwing a p1626 code could the cylinder be the issue?
i paid a garage $300 to do this and im glad they did it
I still can crank my truck but the fuel pump and dash lights and turn signals won't work. Would this part be the cause of my problem 95 Cheyenne k2500 4x4.
Very good video man ..nice thanks
+Clay Holliman Thanks for checking us out!
Can someone please tell me what the plastic mechanism is that you pull the ignition switch off of.. mine broke and now my key turns with no resistance and powers no accessories.. someone please help!!
Instead of hunting down an inverted torx, I used a torx head screw and vice grips. Done and done.
1995 Chevy truck. Well I put in a new ignition wiring harness switch from 1A Auto $37.95 free shipping and that solved all my pro
Jeffrey Pabian what was the issue?
Where did u get it I can’t find it on there website
I broke the plastic knob where the ignition switch seats on the steering column. What can I do? Super glue? I cant seem to find a replacement part for that online
Does it matter wich side the bottom grey connector go
Does this fix no RPM or speed reading issues?
97 K1500 Tach and Speedo dead this definitely is the fix. Easy enough to diagnose. Put a test light on #20 fuse if no power to transmission this is likely why. Not too hard to do recommend buying E4 and E5 deepwell 1/4 inch set. You don't need to remove the steering wheel.
Thanks for your comments and for watching! +Dale Everhart
happy to hear a 97 chevy takes this I was gonna be mad if this thing wasnt the fix
Been to your guys website but you guys don't have one for a 97 GMC suburban c1500
Hi my problem is the key switch { sound} and exterior lights stay on after the key is out and off , do i replace the ignition switch or the key cylinder ? please help .
Super helpful-thanks!!
I dont understand why you removed the steering wheel...
You dont have to. You just gotta figure out how to ge the wiring to come off. He didnt explain near adequately.
8:48 i damaged those wires will it cause any problems ?
I got a problem with my 1995 chevy, sometimes it dies when i turn the right or left signal or press on the brakes. I turn back the key and than forward and starts again. Could it be the ignition swith?
Turn signal or step on the brake to put into drive it just dies? Like doesn’t choke or anything just acts like pressing the brake means I turned the key off..? Mines doing the same thing and I’m going nuts trying to track this down
My turn signal also out and all guages but flashers work. About to change now, finger's crossed
Nice video but no need to remove airbag or steering wheel
Thank you Brother!
Another wonderful I hate vehicle designers moment.
I have a 95 diesel and one day I went to start it up and nothing. I had zero issues with speedo transmission etc. I waited a push button switch up and that worked great for a few weeks. Then my glow plug light stopped working and it was crank city no start. I checked voltage on the harness weird and one has zero current. I will be picking up that e4 bit tomorrow and finishing this job. Hopefully that does the trick. Really want to get the new tires back running...
+Dixieland Holdings LLC Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
I have a 98 Chevy c1500 w/t 4.3 rcsb . Security light on permanent. Unfortunately I disconnected the battery and now it starts and shuts off immediately. What can I do? Also do you have an ignition switch for my truck?
Security relearn
could the ingition swith be the cause that my transmission does shift gears. because when i hit a bump mine shuts off and i have to tap the ingntion swicth , so my transmission can do its work onces again.
Angel Renteria yes it can.
Could a failing ignition switch cause no speedo, tach, or gear select indicator, and no power to transmission fuse?
Yes but if that doesn't fix it could be the ecu but more likely the ignition switch I had the same problem
95 chevy, where is the ignition relay? please help
I know this is a year old thread but I'm just curious of what pad under the key Tumblr is for the rubber pad with the deal slots on it
I have this same truck almost. And I have trouble starting it. It'll start to turn over but then just stop and it'll just struggle to turn over. It's almost like it loses power to start and then a few seconds later it gets it back . I'll turn the key again but just slightly and it usually fires right up. Any ideas on what the problem is.?
I have the a similar problem to my 98 k2500 454. Suburban it will crank the engine but wont wont start i changed the fuel pump and fuel filter sparks plugs etc but i cpu says its an ignotion problem i havent changed it yet im guess i might have to change the ignition harness also
Hi , Do you have a vid on doing this to a 98 astro van
+Max Stevens We do not have a video for this repair right now, but we'll keep this request in mind for a future video! 1AAuto.com
My truck fuse 40-a fuse / ignition keeps blowing out. I've heard this could be related to fuel pump wiring issues. I jump started the started and even worked after a few cranks. What do you recomend my issue is? Also, please help me locate the area/wires that would most common be the issue at.
Thanks in advance.
+Eric Martinez We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1AAuto.com
Wow finally done ody that knows what they are talking about
..I have a similar problem..turn key on to crank and guages don't work ,no power to starter and every thing else has 13.6l8ghts,radio,everything ,can even cross out starter and it turns over but no fire to ignition....0lease help0
I’m starting to think this is the cause for my truck losing power just long enough to reset the computer and clock. Thanks for the video. I’m gonna do some investigating.
I have a 98 astro , if i turn the key and it dont start But I play around with the tilt , up and down and then it starts , Do you think I need this kind of part on my van, thanks in advance.
+Max Stevens We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1AAuto.com
Would the ignition wire be the cause of a no start no spark no fuel pressure?
Jnez08 did you find an answer for this question? I was told yes this will cause a no spark issue and code usually ends up stating it is a Crank shaft position sensor.
I get the same thing without removing all that steering column now my truck won't start after I get that maybe a month later it's not getting no fire I think it's a anti-theft system help can somebody recommend somebody that can fix my truck they was on it for 2 years okay if there's somebody else that can help me please text me back
😍😍😍 I have a 96’ Silverado crew cab
Removing the steering wheel was totally unnecessary to do this replacement.
I did happen to notice that he forgot to put the snap ring back on. Other than that it was a great video
I did this without removing steering wheel
Yeah dude way over did it
Could a bad ignition switch cause my 95 silverado to not shut off when key is in off position. Also dash lights stay on when truck is off
+Cody Stanfield It may cause this type of a malfunction. 1aauto.com
Cody Stanfield
How was it fixed
1A Auto Parts aye when yo car sometimes crank is that cause of the ignition starter switch
So my 95 Chevy k2500 cut out on me and turned back on when I was juggling the keys the lights turned on. I went to start it this morning and the light only turns on on the dash at a certain point when my key is turned to the off position and when I go to cycle the light cuts out. Would this be my problem?
+Dusty Berkram We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
He Should have released the E Brake Handel before the screws ‼️
When I put the lock cylinder back in it won’t turn so I can get the key out but it turns to the battery on position and start position, any ideas?
I had that same problem. I used a dead blow and tapped the cylinder with the key in a few times and got it to move.
Will a bad ignition switch could cause my rpm and mph gauges not to work and also cause transmission not shifting
yes
Definitely !
it can but its prob the speed sensor on the trans.
Mine started doing the same thing did you get yours fixed? If so what was the problem
@@jerryrod83 I am. Having the exact same issue I am replacing the switch now it is a pain n d ass, lmk if u haven't got your fixed or if this was your fix
Puedo conseguir todo tipo de cables para chevy por ejemplo los harnes para una chevy 96
Quick question can a bad ignition switch cause misfire or stalling?
+Bill Wallace Thanks for watching! Yes, a bad ignition switch could cause a misfire or stall! www.1aauto.com/ignition-starter-switch/i/1azis00005?TH-cam&CTA+Comment&YwLg3JYOYYA
What do I do if I broke the plastic piece that the switch slides on to
Will this make my shift solenoid in my transmission to go bad?
+Bill Curry Thanks for watching! This part is only related to the vehicle start up. If you are having issues with your transmission then there is another problem. 1aauto.com
@@1AAuto okay thank you I had my transmission rebuilt just a little while ago had trouble with it and knew was the shifting solenoid they replaced it and they blamed it on the starter ignition
@@billcurry7121 I have the same problem, did you fix it?
Why didn’t you put the snap ring back on?
I had an issue where my vehicle would start with no key, or any key would fit and turn the ignition. I replaced my ignition lock cylinder, and now my new key won't come out, It don't look like my key is turning all the way into the off position. My question is, would a faulty ignition switch like this cause a key not to turn all the way off? Thanks!
+Jake We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
is there any tools/toys that can located a broken ignition switch .or . like a a multimeter style toys?
+elvis pressedtalot You can use a Multi-meter to check continuity pin by pin to look for broken wires, check for voltage at the switch as it is operated. It's more common to have the switch wear out internally from it turning over and over again. After you take the column apart to access the wires you still might need to replace the switch assembly after all.
@@1AAuto found out this product .. "littelfuse" 175amp mega was the reason why the dash board wouldnt light up. like no power locks,light, radio, etc...... but after changing it. started right away. being its -19 the last 2 days. im blaming the battery now :/
@@1AAuto im sure of it . the brand name "littelfuse" 175amp . was at fault. first there was no power. but after using the test light.. 1 side of the fuse. lite up and the other line that leads to the alternator didnt. . so after changing that.. i have power to the dashboard now. and now 1 of 2 things is preventing it from starting.. (starter) or (Alternator). gonna guess it . having an alternator on hand. . starter is gonna have to wait
Thank you for your reply! We wish you luck with your repairs and if you need any assistance locating parts for further repairs please feel free to contact us 888-844-3393 and we would be happy to further assist you, thank you! +elvis pressedtalot
Easy test if it is your ignition switch is not working . If you’re tac. does not work, speedometer is not working properly, shift indicator light is not working, and your transmission is not shifting or stuck in 3rd. Here’s what you do to test your ignition switch. With the engine running, hit the back of the Key and drive into the ignition switch. It might take a few sharp hits but see if your tech starts working. If it works I believe everything else will too. This procedure confirms your ignition switch is bad. It comes as an assembly wiring harness. I just ordered a wiring harness through (1A Auto )for $37 and will be putting it in shortly I believe this will cure of my problem.
+Jeffrey Pabian Thanks for the interesting tip and continued support, Jeffrey!
What if the truck wont start bit it cranks i already changed the spark plugs and coils aslo the fuel pump and filter i haven't changed my ignotion switch even though it says it on the computer will reprogram the ignition swith when i get a new one ? Also do i have to change the ignition harness aswell?
Does this part fit the 97 K1500?
+D Bo Thanks for checking us out! This particular part is not going to be compatible with the 1997 K1500, it only goes up to 96. We currently do not have one that will work with the 97 year. We are always receiving new stock and may carry it in the future so be sure to check back!
AOK thank you
Ok, what do you do if you dont have the key?
I have a 2000 suburban. I turn my key forward it starts fine. When it is started the key will not release back by its self. I will have to turn the key back manually when started. I did try to replace ignition itself and still continued. Would this be an ignition switch issue ? Thank you for any help.
Can a bad ignition switch cause the starter to crank before I turn the key all the way? In “on” or “run” mode it starts cranking the engine and won’t stop unless I turn the key off. I think the starter is staying on and squealing when the engine starts. It literally starts to crank before I turn the key to start it. So weird.
+L H We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
How to remove ign switch on a 97 1500 Chevy pu
I imagine the 97 c1500 requires a different ignition harness
+Edwin Rodriguez We currently do not have an auto repair video specific to your vehicle. You might be able to apply some of the basic steps shown in this video to your application. We do not currently offer the correct harness for your application. Hope this helps you out
You do not have to pull the steering wheel. There is no point at all (this is for trucks without airbags, I do not have them so I wouldn't know if it matters or not if they are there)
Order an E4 deep socket online before you tackle this. There is a special one made for these vehicles.
Lmfao im pretty sure 😂
make alignment marks on the steering wheel and the mounting bolt if you are annoyed by your steering wheel being one tooth out of truly straight.
1A Auto Will a bad ignition switch in a 1995 Chevy K1500 cause a 4L60e transmission to stick in 3rd gear and no Overdrive every now and then? My truck is fine but at the end of the day it'll stick in 3rd gear and not go into overdrive until I pull over and turn the truck off or unhook the battery after that it's shifts fine
My k1500 is doin the same this did you ever figure out the problem
@@dallasjordan3548 The same thing happens to me, did they fix it?
The same thing happens to me, did they fix it?
Symptoms of a bad ignition switch are no tac or speedometer working to include odometer stops working also. Transmission feels like its slipping and not shifting correctly. Problem solved by replacing the switch. Was worried that it was the ECM much more expensive. not much content on the web about this fix.
+Ryan Wilcox Thanks for the feedback!
I can't be the only one who noticed that haggard mismatched door handle!
What if I cant turn my key at all
This switch will cause trans codes like p1860 so if you think your trans is gone it’s probably this switch trans fuse runs with the cluster 🤷🏻♂️ who knew
+19 89 Thanks for checking us out!
Didn’t really see the point in taking the steering wheel off lol looks like can wiggle the ignition switch out with steering wheel on
Do you have a video for a 92 firebird
+Rebecca Islas We currently do not have an auto repair video for this particular repair. Thank you for asking. 1aauto.com
do you have a video for a 2000 blazer
+J Curtis Thank you for watching. Unfortunately, we do not have a video for your application. We will keep this in mind for future repairs. www.1AAuto.com?TH-cam&CTA%20Comment& 866-403-3393