Rebuild KYB Open Chamber Forks Without Special Tools
ฝัง
- เผยแพร่เมื่อ 1 ต.ค. 2024
- 🔥In this video I will teach you step by step how to rebuild your KYB open chamber forks. I will also be giving you examples of how to get the job done without buying/using any special tools. I do recommend using the correct tools, but if you are in a pinch, you can rebuild your forks without them which I will go over in this video.
If you decide to purchase the tools used, show your support for free! All tools that you will need for the suspension rebuild are linked here in the description below from Rocky Mountain ATV/MC. When you do this, you are directly supporting me and this channel. Thank you 🙌🏼
🔥14MM ALLEN SOCKET: amzn.to/3O0NFuO
🔥FORK SEAL BULLET: www.rockymount...
🔥FORK SEAL DRIVER: www.rockymount...
🔥FORK OIL LEVEL TOOL: www.rockymount...
🔥 MAXIMA 5W FORK OIL: www.rockymount...
🔥 PROX FORK AND DUST SEAL KIT: www.rockymount...
🔥 PROX FORK BUSHING KIT: www.rockymount...
🔥 1 1/4' CLOSET ROD: www.lowes.com/...
Engine Tear Down Part 1 Video: • See How Easy It Is To ...
Engine Tear Down Part 2 Video: • 92-04 Kawasaki KX250 E... E
1999 KX250 Splitfire Rebuild Series - Part 1: • New Two Stroke Project...
1999 KX250 Splitfire Rebuild Series - Part 2: • SOS I Need Your Help |...
🔥Rocky Mountain ATV/MC: www.rockymount...
🔥JIS SCREWDRIVERS: www.prymemx.co...
🔥TUSK CRANKCASE SPLITTER: www.rockymount...
🔥TUSK CRANK PULLER/INSTALLER: www.rockymount...
🔥TUSK BEARING REMOVAL TOOL: www.rockymount...
🔥TUSK CRANK BEARING REMOVAL TOOL: www.rockymount...
🔥Amazon Crank Bearing Puller: amzn.to/3NnfuMr
🔥EXTENDED BLIND BEARING PULLER: amzn.to/3p7oI7d
🔥Vapor Blasting and Zinc Plating Services: / moto_resurgence
motoresurgence@gmail.com
🔥SOCIAL MEDIA: Instagram: / greghitchko motoresurgence@gmail.com
🔥EMAIL hitchmotoko@gmail.com with any questions or inquiries
🔥RMATV/MC OEM Parts: www.rockymount...
🔥PROX PISTON KIT: www.rockymount...
🔥MOTION PRO TORQUE WRENCH ADAPTER: www.rockymount...
🔥MAXIMA 80W MTL TRANSMISSION OIL: www.rockymount...
🔥MAXIMA COOLANOL: www.rockymount...
🔥MAXIMA QUICK MIX CUP: www.rockymount...
****TOOLS****
🔥DEWALT IMPACT GUN: amzn.to/3wQgTl8
🔥DIGITAL CALIPER MEASURING TOOL: www.rockymount...
MUSIC: EPIDEMIC SOUND www.epidemicso... This video is NOT sponsored.
Some product links are affiliate links which means if you buy something I'll receive a small commission.
Thank you for supporting the channel!
Back in the day my dad would cut a slit in the old seal, and use it to drive in the new
I've also seen that done too! Good stuff dude 👍🏼
I been blowing these videos up since I acquired a 99 kx250.thanks for all you do! Very inspirational
Right on Kyle! Glad you are finding value in them. Let me know if there's anything I can help with. Have fun with the build dude💨
Hello! Greetings from Argentina, I have a 1994 KX250 and I wanted to know how many ml of oil to put in it, I added 560 ml as the manual says. But I think I was wrong, right?
Hi, do you know if the forks you are dismantling in the video are the Kayaba 48mm USD that the Kove 800X PRO is fitted with? it would seem so, apart from the color of the tube and the fork leg.
I made the tool and it worked perfectly. 10/10. Thanks for the videos!
Dude this is the raddest news I've heard in a while. So glad you made the tool and it worked for you! Thanks for trying it out and leaving the feedback. Little elbow grease goes a long way🙌🏼. Thanks again!
Thanx very helpful 😊 rebuilding yz 250 1997
Hi, do you know if a zeta lowering kit can be used in these style forks? Looking to lower a 01 yz125.
So couple things I have Wp open chanber same concept but I didn’t do the compression chamber to tjing or take out the push rod
Great video, I used this video as a guide to rebuild my 2000 yz250 forks. They work amazing now and no more leaks. Thanks!!
Are the forks the stock forks? Mines are leaking and I want to rebuild them as well
Awesome dude! So glad this video was able to help you out. They are pretty much the same forks! i appreciate the feedback as well. Ride hard, be safe!
Yessir, these are the stock forks, good luck with the rebuild when you try it. Let me know if you have any questions!
I rebuilt a '99 too. The 99 gear ratios are horrific. I swapped in a 95 kdx gear cluster for a wider ratio. After the first rebuild on the forks, the tool isn't really needed. I zip mine on and off with an impact.
Great info! Thanks for commenting my dude. I'll have to look into the gear ratios
@@GregHitchko If I remember correctly, 2002 had a very likeable set of ratios. On my 99 1st and 2nd felt like the same gear. If you need bushings for your gear swap, let me know. Since I did mine I acquired the skills to turn my own.
Thanks greg from 🇵🇭... New subcriber...
Awesome dude! Hope the video helped 🙌🏼💨💨
Made my own tool thanks brother
Heck yeah bro! Glad you were able to make it happen. Thanks for the feedback
@GregHitchko watched the video 10 times cause I was stoned spent 20 mins in home hardware just to buy the wrong pipe and found a metal jack tube I cut the end up on and made it work lol
I keep blowing my 05s… No whatever what I do.. I think they are tweeked :/
Damn they must be! Strange that they keep blowing out on you. You should be able to find those forks for pretty cheap on eBay
You need to make sure your forks are parallel. If the bottom of the forks are pinched inward, you put a bind on the insides of your fork seals making them wear FAST. Motion pro sells a tool to align your forks or you can try the bounce method.
On the stand loosen the axle pinch bolts opposite of the axel nut, take of the stand and cycle or bounce the front suspension. Then carefully snug the axle pinch bolts. Put back on stand and torque everything with out loosening. This method will set the forks parallel. I had the same problem years ago, actually bought the motion pro tool and use it a lot more than I thought I would. The tool is not bike specific so you can use it on any bike.
I wish you had made this video 2 years ago! I just used the impact to get it back together. I did use your electrical tape tricks. I did use Pro-X parts too. I actually thought that was fun to rebuild the forks. I did notice vertical wear through the anodizing on the inside of the uppers? Cab that be stripped and anodized again?
It's pretty fun to get them rebuilt eh?? I really enjoy it. It's not the end of the world to use the impact to get them back together, like I said in a pinch, you'll be fine! Pro-X is some good stuff too 🙌🏼.
I'm not sure of anything to reanodize the inside beside doing kashima coating which is inside and out! I'll have to research👍🏼
Thanks, that was good to see
Great video! You really helped to take the nervousness and unknown away and showing how really easy it is to do by taking a step by step approach and pointing out the finer points. Now, you need to do a set of Showa!! 😅😅
Stoked it helped you out dude! Thanks for the feedback. I do have to edit your a showa one next!
Best guide I've seen. Helped me (a complete beginner) a lot! Cheers!
Cheers dude! Glad it helped you out. I appreciate the feedback on it. Always trying your best make the tutorials better 🙌🏼
Hello Greg. Do I need to release top screw in fork tube cap that regulates adjustment rod?
Yessir, you can do that before taking them apart 👍🏼
I built the tool pretty ez off your measurements and then made it more exact once I had it out
Heck yeah dude, I love it! Stoked that it worked for you. Thanks for the feedback
can i put less oil to make it softer?
Hi mate. The Swm rs300 uses same forks, you wouldn't know what the oil level should be? Thanks
any idea where can I get the diameter INxOD for the pipe? since I cant really find that specific one or order it, I also heard someone who had made it with PVC plastic pipe but cant get the sizes and there are many sizes over here
Do you tighten the top cap down on the rod and then snug the nut up ? I just tightened finger tight and then brought the nut up to it and the rebound seems more open then it normally did when turned in.
Great video!! Thank you.
Does anyone take the inner cartridge apart to get at the o-rings and valves inside it? I tried to separate mine and could not find a way.
Anytime Scott! That is a great question, I was actually wondering the same thing. I was trying to google it myself, but didn't get too far. If I figure it out, I'll whip something up!
I have the same question :(
I cant even get the spring guide out
Need to do fork seals on my 97 kx250, Want to use the links to support the channel when purchasing items. The links are for 2024 kx250. If I use a link to get to RM and then search for 1997 items will that still help out the channel? Also your channel is awesome and videos are very helpful
Heck yeah Anthony, you'll have no problem rebuilding the 97 forks. As long as you click the link, it triggers it on their end. I really appreciate you doing so, means a lot 🙌🏼🙏🏼. Let me know if I can help you out if you need it. Cheers man!
This deserves a like and subscribe from me. I have a 99 125 and my oil seals seem to be shot. I’ve been dreading having to rebuild them but this eased my nerves of screwing them up, and also realize how bad my oil level is in them…😬 thankyou.
Right on dude! Stoked this video was able to help you out. Hopefully you were able to get through the rebuild no problem. Thanks for the feedback as well!
Nice video very clean and clean, im from San Diego California, new subscribers here…
Right on!! I appreciate the feedback on the video. Thanks for hopping on the train 🤙🏼
can i put less oil to make it softer?
Yup! You certainly can👍🏼
"Without special tools"
Literally makes the craziest tool ive ever seen. Great video and thanks for dropping these knowledge bombs on us!
Haha well I guess not any name brand, expensive special tools 😂😂
Amazing video, and custom tool is priceless advice, thank you!!! Saved me so many headaches
Right on man! So glad that this video was able to help you. Thank you for the feedback as well!
That was well done
Good job bud
Cheers Matt, thank you 👍🏼
Are the prox bushings good ? I'm a little afraid them because they are made in taiwan
I've never had an issue but if you are concerned, then oem is also another way to go 👍🏼. They all wear out eventually 😄
I just watch these to give you views 🤣
Can't you loosen the bottom from the damper rod before removing the cap?
You can damage the internals...I don't recommend doing that
Thanks Greg, this is an awesome video!
Yes it is
Cheers for the kind words! It's a good time rebuilding these forks 💨
Very helpful, clear, concise. Good job !
Glad it was able to help out dude! 🙌🏼