There are two lines out of the fuge...the one is clean oil when on and the second is for the fmdirty when you turn it off...it drains to a 5 gallon bucket
Thank you for being very informational. I watched a couple of your videos and they are awesome. I'm thinking about following what you are doing and use it for my diesel generator :)
enjoyed the video. for a WMO recycling project I want to install a brass bulkhead into a barrel so I can control the draining from the bottom to the centrifuge. I figure the brass will hold up better than plastic. it comes with a washer but will it seal better if I use something like JB Weld on it? or is it unnecessary? I'm concerned about the effect of petroleum on the bulkhead and seal. thank you for any assistance you can provide.
I don't think a cotton candy machine is machine to spin this much weight...and do they have a lip to catch things? I think they are just to spin...I think the lip (if any) is super small...wouldn't hold much water and grime
Κωνσταντίνε καλησπέρα από Αθήνα. Ψάχνοντας για Black diesel έπεσα στο βίντεο σου! Θα μπορούσες να εξηγήσεις αν μετατρέπει τα καμένα λάδια από αυτοκίνητα ή από κιβώτια ταχυτήτων κλπ καθως και την γνώμη σου για την μετατροπη(αν είναι ασφαλές, αν αυτά που πωλούνται είναι αξιόπιστα και ο, τι άλλο νομίζεις?)
You could try boiling...just would need it to be boiling to the point water evaporates...but I am not sure because water is heavier than oil so when you heat it the water goes to the bottom...could not work too
+Konstantinos Fotiadis eehmmm boiling water/oil solution? the water will evaporate but its trapped under the oil so the steam pockets tend to burst underneath the oil sending boiling oil across the room, thats also why toy shouldn't put water in a deep frier
I don't think that is completely true...heat rises...so the water being heated at the bottom might work it's way to the top with convection...not really sure.. just brainstorming
Water sinks to the bottom of the solution and it stays there due to the physics of water of it being Polar and having strong surface tenstion, yet it boils at 100C and oil can get way higher so if the oil gets hotter then lets say 120C the water will flash evaporate and explode Konstantinos Fotiadis
@@jasonbrown7258 I use this one now... www.wvodesigns.com/raw-power-centrifuge.html.html A much nicer design...I have an extra for sale if you need one
inside the bowl, they are for draining it once you turn it off. the other hole is outside the bowl in the green cylinder.. that's where it drains into my drum and is clean
sorry i did'nt get it, was this seperating used veg oil into a cleaner veg oil? What was the purpose of the separation? Could it work to separate coconut milk into oil?
i don't know...borrowed from a friend...i have since bought myself one...he might sell that to you...i think he paid 850 for it...interested? if so, i will check with him
This is the best video I have found to explain how one of these works. Thank you.
Nice to see and have explained. Most people just try to explain centrifuge and are afraid to run the system open like that.
Great Job.
is this centrifuge strong enough to filter used motor oil? thanks
There are two lines out of the fuge...the one is clean oil when on and the second is for the fmdirty when you turn it off...it drains to a 5 gallon bucket
Great video..thanks for taking the time to share
Excellent demo of this operation
Thank you for being very informational. I watched a couple of your videos and they are awesome. I'm thinking about following what you are doing and use it for my diesel generator :)
do it...that would be a great idea....this fuge is for sale!
@@konstantinosfotiadis I know it’s a long shot, but do you still have it for sale?
How to clean oil sludge from this machine?
Excellent tutorial, thank you
Hello
Sir, if it was a concussion in the rotating cylinder, does it affect the results?
Do you need methanol for this?
enjoyed the video. for a WMO recycling project I want to install a brass bulkhead into a barrel so I can control the draining from the bottom to the centrifuge. I figure the brass will hold up better than plastic. it comes with a washer but will it seal better if I use something like JB Weld on it? or is it unnecessary? I'm concerned about the effect of petroleum on the bulkhead and seal. thank you for any assistance you can provide.
I don't think a cotton candy machine is machine to spin this much weight...and do they have a lip to catch things? I think they are just to spin...I think the lip (if any) is super small...wouldn't hold much water and grime
Do we have a part# for this thing? I cannot find it to save my life.
Κωνσταντίνε καλησπέρα από Αθήνα. Ψάχνοντας για Black diesel έπεσα στο βίντεο σου! Θα μπορούσες να εξηγήσεις αν μετατρέπει τα καμένα λάδια από αυτοκίνητα ή από κιβώτια ταχυτήτων κλπ καθως και την γνώμη σου για την μετατροπη(αν είναι ασφαλές, αν αυτά που πωλούνται είναι αξιόπιστα και ο, τι άλλο νομίζεις?)
How fast is the rotation of this disc
where does the water go
How much $$ do these cost? How many rpms does it turn? Sounds like its quieter than some c/fuges.
thank you for share your information
Saud Alfhd l
Of when rpm is the motors
You could try boiling...just would need it to be boiling to the point water evaporates...but I am not sure because water is heavier than oil so when you heat it the water goes to the bottom...could not work too
+Konstantinos Fotiadis eehmmm boiling water/oil solution? the water will evaporate but its trapped under the oil so the steam pockets tend to burst underneath the oil sending boiling oil across the room, thats also why toy shouldn't put water in a deep frier
I don't think that is completely true...heat rises...so the water being heated at the bottom might work it's way to the top with convection...not really sure.. just brainstorming
Water sinks to the bottom of the solution and it stays there due to the physics of water of it being Polar and having strong surface tenstion, yet it boils at 100C and oil can get way higher so if the oil gets hotter then lets say 120C the water will flash evaporate and explode Konstantinos Fotiadis
Oil water mix flowing across a heated plate might work.
if you hada oil-water mix what would happen to the water
this centrifuge is for sale if anyone is interested!
+Konstantinos Fotiadis is this equipment is to clean cooking oil 815 999 9368 call me a s a p tomas
+SuperMercado Gonzalez Joliet. Hi. i am the owner of this centrifuge. i just left you a voicemail.
+GW Krauss Did you sell this yet? I'm intrested.
+Wanderlust Bus Still available
+GW Krauss how can I contact you
What is the capacity ?
how many gallons for a minute can be processed ?
Probably 32oz on this one...I ran it at 8 gallons per hour...depends on how dirty you input is and how clean you want your output
@@konstantinosfotiadis what size motor are you using hp and rpm
@@jasonbrown7258 I use this one now...
www.wvodesigns.com/raw-power-centrifuge.html.html
A much nicer design...I have an extra for sale if you need one
Καλό βίντεο σύννομε.
ευχαριστώ!
Lovely, I have been looking for one. At what rpm is the motor rotating?
I have sold this one. I got an even better one now. I dont use it anymore tho
If you are interested in it, send me an email
@@konstantinosfotiadis Thanks for the offer. Surely we can connect. What's your mail id?
Thanks for sharing
hi
it seems that theres no Bee clean company...the website is not ok....can you help me find them?
I don't think they exist anymore...I don't use this one....upgraded to cwvo designs"
I've looked all over the Internet for that machine where the hell did you buy that machine from I want one and I can't find one anywhere
Me too!! I just wish I knew what it was called in honey making circles..I've looked at about 50 different bee supply places
Sounds like an aca P50 tornado siren at full speed
I dont recommend this fuge anymore...check out my newer videos with the wvodesigns fuge
can you please read how much power your electric motor produces?
I'm planing to build my own centrifuge, and this information would help me a lot. :)
Did you manage to build your own centrifuge? You could be of help
whats the website to buy one of those and how much do they run for?
Must take days
Waw thank you
Looks like a centrifuge is in my future
What's it cost ?
what about the drain holes on the bottom of the spinning drum ? where does that oil go ? Do you close off those holes
inside the bowl, they are for draining it once you turn it off. the other hole is outside the bowl in the green cylinder.. that's where it drains into my drum and is clean
How much rpm use to separate oil from particles
I saw one ran at 17,000 rpm
what if there is water in your oil? how to you seperate all the water from the oil? will this centrifuge remove the water?
sorry i did'nt get it, was this seperating used veg oil into a cleaner veg oil? What was the purpose of the separation? Could it work to separate coconut milk into oil?
if you boil the oil, will it remove the water?
well water and oil dont go well together lol. Plus i think that if the oil is gets tooo hot it turns bad.
Don't need to boil You just run it it through a heater to get it to around 185-190 before running through centrifuge and the water will steam off.
of course it could!
greecemonkey? are you from Greece?
Greek descent ,I guess
+pennswoodsed yup! my father is from Kozani
i don't know...borrowed from a friend...i have since bought myself one...he might sell that to you...i think he paid 850 for it...interested? if so, i will check with him
Hi I come from Greece. I don't speak English verx well so can you please answer to me in Greek how Separation of solids and liquids??
Thanks
I found mine used for 750
thanks for prowling to learn and picking out a point that doesn't matter in the grand scheme of stuff....troll on tool
I can imagine why the screen went black when you stuck your finger in the active centrifuge....
Other than that, very informative.
are you greek? Your don't seem be living in Greece though
ok i got it now!
A rotating mass "EXERTS" a centrifugal force, it is not subject to such a force.
Fact! Water is NOT heavier than Oil. Water is more dense than oil which is why Oil floats on Water.
TAKE THE HEATER ELEMENT OUT OF A CANDY FLOSS MACHINE AND IT
DOES THE SAME JOB
kalh magia