I had my transmission rebuilt and the mechanic didn't flash the tcm. I drove off and at light came on check engine light came on. Voltage overload what did he really do to it. He has since change the tcm module and shift valve solinoids . The tcm was not bad before I went in there just to replace transmission what do you think he did to damage the tcm
I programmed a 15 cx5 today and the mmp software gave me the same "form" screen. I used aezflasher2. You probably know this but I'm told you cannot use mmp software on the same hard drive as mazda ids. I had to remove the Mazda ids before I installed mmp. I had never done one either until today.
Hi I have mazda 3 2013 proximity key is the same process, I need to change the used pcm, the ids say programming sucess bat the antiteft blink, what I can do this?
I have a link to the unit that I use on my amazon store, although the picture on amazon is wrong, the link is for the correct unit. www.amazon.com/shop/l1automotivediagnosticsandprogrammingllc
I have an issue i recently had an issue with my mazda 3 2012 2.5L and it has been idling high and low on stops. Then it would suddenly not want to accelerate until i restart the car. I recently did a throttle body clean maf clean changed all o2 sensors also tried to reset ecu by disconnecting negative battery terminal and waiting a bit step by step. A mechanic shop told me to go to my dealership to get a software update to fix the idle issue. You think this is correct ?
Hey dude, thx for the videos. Do you know how to enable cruise control on a Mazda 3 2010? I bought the better steering wheel + the break pedal sensor. Another guy on TH-cam told me to learn forscan
I know your post is old, but I did it to my 2.0 and kept the 2.0 PCM because I wanted to keep my mileage, and it's been running good without a tune for 2 years now.
Couldn’t you just use the cardaq toolbox software to clear codes we have a cardaq plus at work and it in itself with the toolbox software can do some stuff I never use it myself however I have messed with it in the past
Cool glad to see you out there. Good video
I had my transmission rebuilt and the mechanic didn't flash the tcm. I drove off and at light came on check engine light came on. Voltage overload what did he really do to it. He has since change the tcm module and shift valve solinoids . The tcm was not bad before I went in there just to replace transmission what do you think he did to damage the tcm
I programmed a 15 cx5 today and the mmp software gave me the same "form" screen. I used aezflasher2. You probably know this but I'm told you cannot use mmp software on the same hard drive as mazda ids. I had to remove the Mazda ids before I installed mmp. I had never done one either until today.
hi there,
want to ask, can we disable Check engine light parameter when reprogram PCM?. . example: P0421/P0420-emision control parameter.
Hi I have mazda 3 2013 proximity key is the same process, I need to change the used pcm, the ids say programming sucess bat the antiteft blink, what I can do this?
Read the service information. You are not done yet.
Having a p0601 code in mazda 3 05 can it be solve by just reprogram the ECM without replacing?
Thanks for your reply.hoping for it
What type of charger is a good one to use for programming?
I have a link to the unit that I use on my amazon store, although the picture on amazon is wrong, the link is for the correct unit. www.amazon.com/shop/l1automotivediagnosticsandprogrammingllc
Great work mate!
If I have my abs module replaced do I need it reprogrammed? And if so is there any way to just fix the pump and actuator and not the whole unit?
Yes, it needs reprogrammed with VIN. 50/50 on the half fix, the reprogram is best.
I have an issue i recently had an issue with my mazda 3 2012 2.5L and it has been idling high and low on stops. Then it would suddenly not want to accelerate until i restart the car. I recently did a throttle body clean maf clean changed all o2 sensors also tried to reset ecu by disconnecting negative battery terminal and waiting a bit step by step. A mechanic shop told me to go to my dealership to get a software update to fix the idle issue. You think this is correct ?
Sounds strange but you could try changing out or cleaning the EGR valve too.
Hi Mate. can you tell me what ECU interface is used by this Mazda 3 2010 ?
We used a J2534 compliant device.
@@L1Training thanks dude
Where are you located? Do you reprogram gauge cluster miles on a 2013 Mazda 3?
Hey dude, thx for the videos. Do you know how to enable cruise control on a Mazda 3 2010? I bought the better steering wheel + the break pedal sensor. Another guy on TH-cam told me to learn forscan
What’s the price rate for that job?
Doing swap from a 2.0 to a 2.5 on a 2011 Mazda 03, would buying a 2.5 PCM be better or having the current PCM flashed?
I know your post is old, but I did it to my 2.0 and kept the 2.0 PCM because I wanted to keep my mileage, and it's been running good without a tune for 2 years now.
@@sampic_the 2.0 transmission is the same, will it keep up with the bigger 2.5 engine? Thanks
What is the program you use on your cf19
Did you use the FJDS for Ford?
What tool are you using for Mazda?
Cardaq 3, and a MMP subscription.
Couldn’t you just use the cardaq toolbox software to clear codes we have a cardaq plus at work and it in itself with the toolbox software can do some stuff I never use it myself however I have messed with it in the past
@@dblr616 yes,but it wont clear any codes out of the other modules, only the PCM.
@@L1Training is it same with fjds?
What software is it ??
Mazda MMP
Nice job
Which machine or software are u using?
Mazda MMP