all your videos are amazing and extremely interesting. and its impressive that in all these videos all we hear is "safety this" "safety that"...everything is designed with safety in mind. a good educational series of videos for people with fear of flying
Was the garage door closed? Should have left it in gear. I lost a 757 that way. Rolled right out onto the street and got hit by an a321. I think they were texting they said they didn't see it.
I agree this is the best ever DIY clip on changing a tyre..... Takes DIY to a whole new level....... " remember to depressurise the hydraulic brake system, put landing brake on and be careful when removing debris cover for fear of breaking the tachograph. !!!!! Beats the normal ones about the Ford Fiesta !!!!!
You’re absolutely correct, yet in the real world, aircraft mechanics do it this way all the time. It’s just easier to have one tool for both loosening and tightening. Plus the torque wrenches are recalibrated annually, so you would know it if you knocked one out of calibration.
Well you would have to have some basic knowledge of a330 wheel removal of course,but I’m sure the steps are similar enough that you don’t need to spend to much time researching how to remove an a330’s wheels.
Surprising! in aircraft maintenance , all parts are put on the floor, no case, carbord, box! i never do that when i change my car wheels, but it's not a big plane.
Pro tip: trust a nylon tiestrap to keep that 80lb control rod outta the way and stop it from falling on the next guy.. And torque wrenches should be calibrated after beating parts with it.
Nice video, but for a maintenance procedure in a controlled environment, it lacks one safety item. The wheel and brake should have been removed with a dolly designed for this specific job, which allows one person to do the job, much safer than two or three people. The shown procedure is used when one is in the boondocks with little support from better tools. But in a hangar, with the airplane on jacks, it would have looked better if the dolly was used instead of hand labor. Of course, it's much easier to do all this when one is in a nice dry hangar, when the brake and wheel are not hot, or when it's not raining, snowing, 40°C +, or the pressure of passengers waiting, thru flight, etc. But in all fairness, good presentation.
I played a joke on my co worker while we were changing the brakes one time: while he was under the gear removing the brake hub I let the jack down on him...Man u shoulda heard him scream! 😂
This video may have been posted 6 years ago but certain clues like, the body sweat suit, mustache, no PPE, narration and 70’s music lead me to believe it was made in 76’
Let me see if I have this correct: The wheels on a main landing gear are removed with hand tools; the locking bolts are secured with cotter pins; landing gear assemblies are held out of the way with zip ties; break assembly is put on a wooden pallet. Okay, I've got it.
3:35 "unscrew the wheel nut using the appropriate tool" a torque wrench is not used for anything but measuring torque on a fastener and not in reverse. Even I know that and I'm just a truck driver ffs
Never seen anyone depressurizing the hydraulic accumlator since it is absolutely unnecessary because the hydraulic lines to the brake are quick-disconnect couplings.
I’ve never seen anyone pull any circuit breakers, either, though I imagine it would be a bad day if your partner turned on the brake fans while you were trying to remove them.
And that’s exactly how it’s done in the real world, except they would never bother depressurizing the hydraulic system or pulling any circuit breakers, either.
Same thing with ordnance nose fuzes; screw in nose cavity until it stops, back off a half turn and then snap it. Worked everytime for me, don't need torque wrench on flight deck.
Just what I needed. A diy step by step to change the brakes on my A340.
Best DIY video on the tube!! Okie dokie.. time to get back to my garage and finish the job on my A340.
lmaoooo
Haha! Lol - I just have to remove the 4 and continue with the restoration of my A30, which does indeed fit in my garage!
Obrigado por
Thanks! Just ordered my A340 from Ebay so excited to try this!
LOL!!
KKKKK
Just bought a second hand A340 for cheap and glad i found this video. Now i can save heaps by doing the job myself...
Yeah, me too. Can you get re-mould budget tyres for these rim sizes?
. I can pilot for you Cameron, I am awesome on Top Gun the arcade game.
Doh!
I'm an airline mechanic making $150k a year and I watch TH-cam videos to learn to work on planes..... I'll never fly again
+Azdrtdog x
xx
xx
Great tutorial. Now I feel ready to change the brakes on my A340!
Finally, I can put on these new brakes I bought for my personal A340. So good of TH-cam to recommend this to me.
Thanks to TH-cam, after the apocalypse I’ll be able to fly and maintenance my own 747. It’s going to be awesome.
Thanks for the posting. Next time I don't need to go to the mechanics, I will change it myself :)
very useful video, now i can change the brakes on my daily drive...
...Man....I'm LOVING THIS !! AWESOME !!Thank you SO much !!
You are welcome.
awsome now im gonna go change it on my airplane.
excellent sequence wise demo. Useful for trainees.
Perfect Now I just need to buy an airplane thanks 🙏
i love these videos. they are like a haynes manual for your airbus :)
all your videos are amazing and extremely interesting.
and its impressive that in all these videos all we hear is "safety this" "safety that"...everything is designed with safety in mind. a good educational series of videos for people with fear of flying
so this is what i missed, parking brakes. my aircraft rolled out of my garage.
Was the garage door closed? Should have left it in gear. I lost a 757 that way. Rolled right out onto the street and got hit by an a321. I think they were texting they said they didn't see it.
Thanks my friends Very good
Such a great video...Next I am waiting for my flight to board, I am going to go and change a few tires on it. Easy stuff!
Looks so simple and elegant from outside but contains such intricate and complex internal mechanisms. Engineering marvel an airplane.
I think the same thing when I watch a video like this!! Amazing!
Karan Thakur
It is easy but not ths installing part..
Karan Thakur હ
I'm watching this just in case the landing gear brake need to be replaced while I am in the airplane. You never know..
xl
.
Where are your equipments? Are u gonna use toothpick??
XD
Yeah in case you get flat tires there is a spare under the plane.
@@carlmichael4979actually there ıs a spare wheel 😊
:OO Trynkiewicz pracuje przy wymianie opon! Nieźle ustawił się
I agree this is the best ever DIY clip on changing a tyre..... Takes DIY to a whole new level....... " remember to depressurise the hydraulic brake system, put landing brake on and be careful when removing debris cover for fear of breaking the tachograph. !!!!! Beats the normal ones about the Ford Fiesta !!!!!
Now I can change my A340-600 breaks myself. Thanks.
wow i was looking for a video on rear drum brake replacement on my 94 ford ranger but im sure this is pretty simular ty
Nice video...................
Thank you so much ❤❤
You're not supposed to use a torque wrench for loosening bolts.
But why? I mean it makes the job easier since you can apply more torque on those bolts. With a normal wrench, you need to apply more force
You’re absolutely correct, yet in the real world, aircraft mechanics do it this way all the time. It’s just easier to have one tool for both loosening and tightening. Plus the torque wrenches are recalibrated annually, so you would know it if you knocked one out of calibration.
Will this work on my a330?
Gamebreaker08 no
Gamebreaker08
Well you would have to have some basic knowledge of a330 wheel removal of course,but I’m sure the steps are similar enough that you don’t need to spend to much time researching how to remove an a330’s wheels.
Yes. A340 and a330 wheels are the same. Same landing gear.
will this work on my a380???
No, because of French logic.
Shaun Janssens
adgyjnfb
Mala Ara A
FLL aviation central bjhnlbhnkhnmjbmivnmnb lb.kb lhivkubnkbnkbmkbmjnmb lbjgnib
FLL aviation and railfanning it will
Mantapp
love the video
Surprising! in aircraft maintenance , all parts are put on the floor, no case, carbord, box! i never do that when i change my car wheels, but it's not a big plane.
Ok job done, now i need a tutorial for the turbine impeller change, thanks
Great video.
wish my Ikea furniture had an instructional vid like this
Krishnan RV
Is there a glove shortage there?
Tough mechanics always don't use them. 👍
COOL!!! I have the same brakes on my 97 Dodge Caravan...
so if a flat tire leaves you stranded on the side of the skyway, you'll know how to put on the spare
Can't wait for my new A380 wheels to arrive.
This not the procedures for change wheel and brake assy, the technicians must be use gloves and crane and hoist for removed the brake assy......
Interesting 👍👍 subscribed
I did this but I think there's still some air in the system. What is the proper way to bleed A340 brakes? Feels more complicated than my wife's A318.
🤔🤣🤣🤣
Pro tip: trust a nylon tiestrap to keep that 80lb control rod outta the way and stop it from falling on the next guy.. And torque wrenches should be calibrated after beating parts with it.
very nice
Super
Otro nivel
FULL FLOATING BRAKE PACK,GOOD GEOMETRY.
👍
Thanks..do you have also B777? and more A330,340,321,320..
kiefer lasticman hgjgm
Big job , very cheap tools it's very funny.
Nice video, but for a maintenance procedure in a controlled environment, it lacks one safety item. The wheel and brake should have been removed with a dolly designed for this specific job, which allows one person to do the job, much safer than two or three people. The shown procedure is used when one is in the boondocks with little support from better tools. But in a hangar, with the airplane on jacks, it would have looked better if the dolly was used instead of hand labor. Of course, it's much easier to do all this when one is in a nice dry hangar, when the brake and wheel are not hot, or when it's not raining, snowing, 40°C +, or the pressure of passengers waiting, thru flight, etc. But in all fairness, good presentation.
You people at main lines are so spoiled
Couldn't agree more..
I was just in AutoZone the other day and says to myself.....Self.....remind me to ask them if they have brake rotors for a A340 center bogie axle.
were safety srews installed correctly ? on 03:18
I played a joke on my co worker while we were changing the brakes one time: while he was under the gear removing the brake hub I let the jack down on him...Man u shoulda heard him scream! 😂
Handy DIY.
If you own the same aircraft 😆
Somehow I don't like the way they work. They guy kneels on the concrete, the parts are scattered on the floor...
Carl Napp Thought the same thing. You'd think they'd have a specialized cart or something.
Carl Napp Yeah, What happens if your changing jet tire overlooking a mountainous cliff & by accident kicked the hubcap over the cliff?
+Duane C 🐶💄😁😁😂😂
Brad
Yes, imagine he would be diverted by an insolent trash-talker!
,+Carl Napp w
This video may have been posted 6 years ago but certain clues like, the body sweat suit, mustache, no PPE, narration and 70’s music lead me to believe it was made in 76’
Will This Fit My Honda.
Anyone know the torque spec for the axle nut? Trying to get this job done before dark.
It’s in the pubs....
'
wow alot of brake pads on the wheel...
do have ball bearing on the axle or not
5:02 is that a freaking 16 piston clutch break?
Will it work on my bike ?
Where were the wheel bearings?
nice
I had a bad headache after watching this video.
Please show in close up removing the cotter pin, unscrewing sensor etc.
Let me see if I have this correct: The wheels on a main landing gear are removed with hand tools; the locking bolts are secured with cotter pins; landing gear assemblies are held out of the way with zip ties; break assembly is put on a wooden pallet. Okay, I've got it.
Yep
Very useful! :D
اللهم رد كل غائب ومغترب لبلاده بامان وعافيه يارب
+Aziz Garut Yeap..I totally agree.
I was just wondering what kind of brakes those things have
Wear safety gloves please
Next time. 👍
3:35 "unscrew the wheel nut using the appropriate tool" a torque wrench is not used for anything but measuring torque on a fastener and not in reverse. Even I know that and I'm just a truck driver ffs
Yup, that’s what I saw too.
OMFG......
And yet, that’s the way it’s done every day at airlines all over the world.
Not keen relying 100% on a hydraulic jack! No Fixed stands?
the entire plane is sitting on massive jack stands, the hydraulic jack only compresses the strut enough to raise the wheel off the ground
We’re can I get the rubber work outfit it looks cool
Ask your gay buddies, they'll have one.
Just check it out it's a very interesting system, stator rotor, stator rotor, stator rotor etc etc....hey
After watching this video alone do I qualify to become an airplane mechanic?particularly a wheel & breaks maintenance man?it really looks easy to do
Thanks! This tutorial has saved me a ton of cash. Anyone have a link to do engines?
1:30 Did he say "taco-meter?" As in, "How many tacos are inside that wheel hub?" Never heard anyone say tachometer like that before.
npsit1
This would be a good commerical for GoJo.
Chris fix would love this job
HAHAHA Hey guys Chris fix here and today i m gonna change the brakes of an airplane hahaha
One day wheels will be a thing of the past
I don't think soo.
On the plus side, chavs will struggle to steal those wheels.
Mahan Air: now we know how to fix our planes, they came without a catalogue
Most of you guys don't know how to speak / read English. Once i wondered how pilot fly this piece of machine.🤨🤔
@@SUPERCHARGE7 not worst than Russian or Chinese pilots🤣
@@mss4822 totaly agree 🤣🤣🤣🤣🤣👍
Please give this guy a pair of work gloves
I just did this job in my garage the other day
Never seen anyone depressurizing the hydraulic accumlator since it is absolutely unnecessary because the hydraulic lines to the brake are quick-disconnect couplings.
+warpigxp It might be a safety layer in case the quick-disconnect fails to close automatically once disconnected.
corisco tupi Yes of course, you're totally right. I just have never seen anybody doing it :-P
I’ve never seen anyone pull any circuit breakers, either, though I imagine it would be a bad day if your partner turned on the brake fans while you were trying to remove them.
can anyone tell me why is the wheel rotated in the same direction as the wheel torqued?
It's to gain a more accurate torque measure. of the wheel nut.
It’s to make sure the bearings are fully seated on the axle and not binding.
Nice to see that even $300 million dollar jets also use cotter pins to secure wheel nut! I guess why make things complicated.
No gloves, no safety glasses, things laying on the floor to trip on, using a torque wrench to loosen things.
That's exactly what shocked me too!
So?
And that’s exactly how it’s done in the real world, except they would never bother depressurizing the hydraulic system or pulling any circuit breakers, either.
I always use the German torque standard..."GUDntight"
villageidiot bcddj
Same thing with ordnance nose fuzes; screw in nose cavity until it stops, back off a half turn and then snap it. Worked everytime for me, don't need torque wrench on flight deck.
Where are the gloves?🤔
Gays use gloves.
Tough guys using tough hands.
Gotta get me some of those brakes for my Miata.
Jworg
This is a maintenance video - not meant for the general viewer.
+hawkeye0248 OK
Brakes look a lot different than what I expected
THE GUY HAS NO APROPRIATED TOOLS TO WORK....UMBELIVABLE
I would want alloys on my plane yeah?
خیلی جالب است مرسی
Обалдеть, насколько всё сложно... не удивляюсь, что ни у одной из а.к. РФ нет подобных воздушных судов...
재밌겠다...
Now I know how to do it. #DIY