WOW, Joe!! You're only 17 and want to go to college to be an engineer? I'm super impressed with your motivation and determination young man. Nice to see young people so beholden to carrying on the legacy of tube amps.
A couple notes after playing the amp for a few months: - don't cheap out on the speaker baffle wood like I did. I used scrap ply and it ended up warping a little bit, so I had to make a new speaker baffle. - use tougher grille cloth than I did. Another reason for my speaker baffle replacement was that the stretchy material I used got a little loose over time and I knew it wasn't doing much to protect the speaker. Now I'm using a tougher, non-stretchy acoustic fabric for the grille cloth. - I used some pretty low-quality tube sockets because I just bought the first ones that looked good, but they’re really loose and difficult to use so I’m replacing them with nicer ones.
You did quite good in terms of component quality, with the exception of the tube sockets. I would had bought Belton or NOS Cinch sockets and used those instead of those iffy Chinese ceramic sockets.
I love the fact that the build isn't perfect, this is a superb example of imperfection being individual and a lesson along the path. Much respect Joe, excellent video.
I built my first guitar amplifier using 12AT7 and KT66 valves when I was 16 years old, which was 50 years ago now! However, your workmanship is way better than mine. It all brings tears to my eyes. Congratulations on your achievement and keep up your good work.
The same for me. 50 years ago, I was 16 too. EF86,12AT7, GZ34 rectifier and an EL34 push pull. Congratulations, you work is much better than mine. Thank you for bringing me decades ago.
Dynamite. Yes, Uncle Doug is the greatest tube amp repair site on all of TH-cam. Rob Robinette has done an incredible job annotating schematics. Keep up the good work! I use a spring loaded auto punch prior to drilling.
Fabulous job. It was great that you built every part from scratch. Your video is a joy to watch (3 years later), I'll bet the amp has brought you a lot of pleasure!!
You did an excellent job considering it's from scratch. Building from a kit is hard enough but to build your chassis from scratch and gather all the parts yourself proves your ambition. I would love to own that amp.
There are so many 5E3 clones available and a bunch of kits. Makes sense because the 5E3 Deluxe sounds great, is versatile and a relatively simple circuit. Joe Les took it one step further and built from total scratch. Awesome and damn fine work!
Wow, very nice amp! I want to try to lacquering canvas over a cabinet like this for a super-old school look. We have a saying: "A good solder joint starts with a good mechanical joint." In this case, pull the wire or component lead through the solder eye, and bring it back to itself. Don't twist it. Pinch them together forming a nice parallel section of 1/8" at the eye. (Meaning, don't leave a big stub.) Then flow a good solder mass that encapsulates the entire interface. It should look like it was dipped in thick molten metal that formed a teardrop shape...no rough surfaces or voids. That takes HEAT on the ENTIRE joint. Use plenty of flux and LOWER temp tin-lead solder for best results. Also, thermal cycling causes a lot of expansion & contraction in conductive material...any metal. So, leaving a little extra "service loop" adds tremendous life to those solder joints. (That just means leaving some extra lead length to prevent them being too tight...not an actual loop.) Finally, solder joints are the highest failure mode in this sort of device...meaning they crap-out first! Joints that look good, but weren't heated fully are the enemy: A "cold solder joint." They work when new, but die over time. Before they go completely, you often see resistance changes & intermittency. Avoid them by following my advice above. Good job on this...rock on brother!
Very nice build. This video just popped up and I probably would have ignored it but when you mentioned Uncle Doug early on that was enough for me to watch it. Great work.
Having re-built several old tube amplifiers, I am hugely impressed. Your attention to keeping it neat and simple looking, while being a complicated work of art is so beautiful. I really like your choice of wood finish instead of tolex. Nothing wrong with tolex, but your amazing routed fitted corners and natural wood grain is just Tops. Just an absolutely beautiful job, and it sounds wonderful.
I give you praise for this build I love how raw and vintage this amp looks I loved how you built your chassis and cabinet this amps sounds better than some boutique 2000 dollar amps.
Well done! Great effort. I liked how you started again on the chassis. That's the kind of thing that I do as something like that keeps me up at night. Also taking the build outside to the yard, yep, can relate again. Beautiful result, great stuff!
Thanks! Watching your amp build a while ago was actually one of the first things that gave me the idea to do my first build (a champ) now that I think about it. And yeah I am really glad I started over on that chassis haha
I'm glad you enjoyed it! This actually wasn't my first build; I built a pretty rough-around-the-edges fender champ a couple years ago, but this was my first time really going all in and trying to make it look really good.
Thanks so much for sharing that. I’m good on electronics, but the woodworking and the metalworking…I would never be able to do but it’s great to see someone else do it! Sounds great. Also nice you update below with changes (baffle, tube sockets, etc.). Thanks so much!
Amazing job! I ended up here because I wanted to build my own tube amp. I have a huge box NOS tube from the 60/70's and I really wanted to make a few tube amps with them. I was ready to be COMPLETELY overwhelmed, but dag gummit, you made it look so clean and doable, I am no longer scared of trying it. Thank you so much for that! Well done!!!
Great job, young man, very nice workmanship... Only thing I see that I would mention is the output transformer should be at a 90° to the power transformer (so 1/4 turn) to cancel a magnetic field for noise canceling purposes look it up on the channels you listed. It sounds good however and I wouldn't worry much about it, but something tells me you will be doing more of this. Knowledge is power, carry-on! ✌️👍
Top marks for using the "Template" and "well done" on the cabinet. I can imagine it in shrinking black gloss wood paint with laquer for some reason. The bigger cab dimensions are a great idea, I had a Blues dlux which I gutted and kept transformers and chassis and tweed cab(stained with shellac) the cab is bigger than a 59 type, put a Jensen P12Q in it and handwired an improvised an ab763 to run 2 6L6s with proper valve reverb simple bass/mid/treble. Keep it all simple as poss. Good stuff!
I loved this video. It inspired me to do the same while convalescing from heart surgery. I haven't yet started an amp build project since short term disability doesn't pay much, but I hope to in the future. Thanks Joe, this was awesome.
Rob Robinette + Uncle Doug is a winning combination, thanks to them I haven't blown myself up (yet). I've just finished a 5F6a head with a few of RR's mods (including the stealth speaker!) - his site is a brilliant resource, the startup & troubleshooting sections are invaluable. The layouts are great too - I've built a few amps following them and haven't yet found any errors (unlike a few others I could mention😄).
yep, both of those resources have been soooo valuable for me as well. I remember when I first had the idea of building a guitar amp a few years ago I had no idea what was involved, but Rob's site was great and I successfully built a working champ. All of the online forums have been great too.
@@joeles2738 The initial plan was for a JTM45 but the chassis was massively delayed - I got impatient & decided to do the DR while I was waiting. Obviously a big learning curve but I managed a working (& humless) amp within a couple of weeks. After I'd built a few more amps (and watched way more Uncle D videos) I went back to it and did a complete rewire cos it was a bit of a rat's nest.
Great build dude! That G12Q speaker really impressed me. For me it was the icing on the cake of this build. I love how I can get lovely big rich cleans playing normally, but if I dig in, the speaker just EXPLODES. A lot of people hate early speaker breakup but for me its fantastic as it really adds that "melting tweed" vibe at usable volumes.
I think the best advice you gave was that you viewed other builders sites and TH-cam channels, and learned a lot about what and what nHhstarted ordering anything. I also liked 🎉that you left the pine cabinet, and just poly or clear coated it, looks much nicer and more custom than had you covered it in tolex like everyone else does. Sounded good too, really nice job!
This is really nice work. The only thing that lets it down cosmetically is the grill. That would be easy enough to change, given how it's attached. Some vintage grill weave material would be for more in keeping with the rest of the style and would set it off perfectly, I think. In any case, the box and chassis are gorgeous and sound the part for sure!
Wow. Just wow. I really want to start building one and seeing this has given me the inspiration to do it. Luckily I have a lot of tools from 30 years of work but I will be please if mine is half as good as this.
yeah, I've never used an eyelet board before but I kinda feel like turret boards would be easier to solder to. Also I feel like it would be kinda tough to build an eyelet board yourself
@@joeles2738 Eyelet board are pretty easy to make, I use 4mm centre hole nickel plated eyelets, as used in leatherwork. They take solder really well. I put them into 2mm paxolin, or whatever the equivalent is called in the USA. It works out much cheaper, and to me look neater than turrets.
@@chrisbarrett5132 oh nice! I think I still prefer the look and toughness of a fiberglass turret board but I guess it’s just a personal preference thing
If you anneal your aluminum with a propane torch at the lines you want to bend it will make it bend like butter. I was a toolmaker for 30 years with amp work as a sideline so it gave me a good knowledge of metal work for chassis building.
fun build! I used a beehive kit from Tractor Supply to build my cabs, head and speaker cabs...worked great and saved huge time with limited tools and carp. skills....just say'n
Yep the deep beehive box is almost identical size to the 5e3 cab. I did one and turned the boards inside out so the handles were on the inside. It’s convenient and finger joined too though Next time I’ll buy the wood and hand make the joints.
@@davidsimpson3380 I've done a few since using The Behive Boxes...a nice 5f1 head and a mojo stidio 1 head. My routing work is improving! I might work on finger joints next...though the cabs after tolex applied no one could tell a difference. Uncle Doug has produced some awsome videos on building cabs....those inspired me, not to mention the cost on premade cabs.
Joe, great job! Not only was your planning and execution of the project impeccable, but your video showing all the steps is also exemplary. Keep going!
I have built 3 amps now two 5e3s and a 6g3 head. The head cab and one of the 5e3 cabs I built too and 212 cab for the head. Lots of fun! 6g3 is a Dovetail Cab.
I'm in the midst of building a little bigger amp with reverb and tremolo. Following this one, I plan to build a 5E3 clone as well. Your video was very helpful for my planning.
This is an incredible build. When you can, you might want to touch up your tube socket soldering. You need more heat on the joint so the solder reflows properly on the socket leads. Many of the those fillets are cold. They could fail in time unless you've got smooth solder between the wire lead and socket pins.
Thanks!! I actually have 5F2A Princeton clone that I built for sale on reverb currently: reverb.com/item/58129111-hand-built-fender-5f2a-princeton?bk=eyJhbGciOiJIUzI1NiJ9.eyJqdGkiOiJhNDEzZjY5YS0zNWQwLTQ5NTUtODFkZC0xNjM0YjU5NWUwNjQiLCJpYXQiOjE2NjA0MzgzODMsInVzZXJfaWQiOiI0MjAwNzg0Iiwic2Vzc2lvbl9pZCI6IjVkMWVhNzZlLTE0NTUtNGY0OC1hOWUzLTY0ODFjNDIyNGU2ZSIsImNvb2tpZV9pZCI6IjBhNWQzOTc5LTllMzItNDgwYy1iNDc1LTgwMmU5ZGU3NDcxNCIsInByb2R1Y3RfaWQiOiI1ODEyOTExMSIsInNvdXJjZSI6Ik5PTkUifQ.g93AAznxXTO29I19yVwOpwr0tpaxllVZU75jsphv120
Congratulations on your first and very nice build! You accomplished exactly what I wanted to do with my build by providing a very detailed description of every step. I tried to video mine and bailed about half way in because I would get wrapped up on the build and forget to record. The time I was spending to go back and reproduce a step or edit a screw up wasn't worth it to me. I'm not a patient person and the build really pushed my buttons a few times. I don't think the general viewer is aware of how much time is required to produce a quality, comprehensive amp video build. Like yours, my first amp was my own design. I started with a flat sheet of scrap aluminum picked from the floor of a trailer shop. Every component and screw was hand picked. It was expensive in the end but worth it. The completed amp is a 5F2A with a C channel horizontal chassis in a 1941 Majestic console record player / radio cabinet with a 12" Jensen C12Q. I wanted different and that's what I have and I couldn't be more pleased with it. I look forward to your next build and thank you for sharing your very nice build.
Had no idea this was even an option. I’ve been looking at getting a tweed delux but didn’t want to shell out money for a new one. This is a great option if you have the skills already.
Nice job! I made a similar amp, a tweed champ, from scratch , but I used 16 gauge steel for the chassis. I didn’t have any trouble cutting it with my jigsaw but bending it was really hard!
That's excellent work, you should be really proud of yourself. Playing through something that you worked hard over, and made yourself must be really satisfying. Just 2 personal preferences on my part, I might have been tempted to make the amp as a separate head and cabinet if you had the wood, make it more modular and can swap out components more easily. And at about 24:25, you pull on your guitar lead a little and risk either damaging the input jack, or pulling the whole amp forward onto its face. This is probably why most amps have their input on the front so that if enough pressure is exerted you just pull the cable right out of the jack. Plus at a glance you can see what the volume, gain etc. is currently at without standing right over the amp. That aside, I'm impressed by your efforts here, well played. 👍
Very nice construction work. I have also really enjoyed building tube equipment this past year. Make sure the solder joints are really hot and fully melted.
Very nice job and a well done video! Nobody is perfect, some are just more skilled at concealing their mistakes. Your video could serve as an excellent tutorial for newbies!
Very Impressed .. it turned out great and as I read .. you've already made upgrades and improvements. I think I too would go with a the natural finish if I had spent that the timed to build the cab! I would be such a noob with the electronics.. you've obviously got a good handle on what you're doing and taking a sensible approach to testing as you go along. Kudos!!
Respect to ya. Definitely a fun process. I've never built my own chassis but have drilled all the holes per my own layout. Built a 5 watt tweed princeton circuit in the layout if a Marshall head. Fun stuff. The hand pick had me rollin
WOW, Joe!! You're only 17 and want to go to college to be an engineer? I'm super impressed with your motivation and determination young man. Nice to see young people so beholden to carrying on the legacy of tube amps.
Wait, he's only 17? I thought he was in his 30's or 40's. Pretty impressive work for a teenager.
@@NostalgiaforInfinity very much so
It looks awesome , I love it,
Thank you boomer.
kids have an idea what they want to do @ 17.. mind NOT blown.
A couple notes after playing the amp for a few months:
- don't cheap out on the speaker baffle wood like I did. I used scrap ply and it ended up warping a little bit, so I had to make a new speaker baffle.
- use tougher grille cloth than I did. Another reason for my speaker baffle replacement was that the stretchy material I used got a little loose over time and I knew it wasn't doing much to protect the speaker. Now I'm using a tougher, non-stretchy acoustic fabric for the grille cloth.
- I used some pretty low-quality tube sockets because I just bought the first ones that looked good, but they’re really loose and difficult to use so I’m replacing them with nicer ones.
Вам что комб не по карману?
@@СотаСота-г3ф what do you mean?
You did quite good in terms of component quality, with the exception of the tube sockets. I would had bought Belton or NOS Cinch sockets and used those instead of those iffy Chinese ceramic sockets.
@@douro20 I received this comment while in the process of replacing those tube sockets with beltons hahaha
Nice dude! Thanks for the tips!
I love the fact that the build isn't perfect, this is a superb example of imperfection being individual and a lesson along the path. Much respect Joe, excellent video.
thank you!
nice burn bruh...
I built my first guitar amplifier using 12AT7 and KT66 valves when I was 16 years old, which was 50 years ago now!
However, your workmanship is way better than mine. It all brings tears to my eyes.
Congratulations on your achievement and keep up your good work.
That's awesome to hear! I'm glad you enjoyed the build and thanks for the comment.
The same for me. 50 years ago, I was 16 too. EF86,12AT7, GZ34 rectifier and an EL34 push pull. Congratulations, you work is much better than mine. Thank you for bringing me decades ago.
That's a really nice looking build.
Thanks! Your website made it a lot easier
Dynamite. Yes, Uncle Doug is the greatest tube amp repair site on all of TH-cam.
Rob Robinette has done an incredible job annotating schematics.
Keep up the good work! I use a spring loaded auto punch prior to drilling.
Thanks! Yeah there's a lot of great information out there
Dude everything about this is killer.
Im mad jelly of that uberpick
haha thanks that pick was $11 but honestly it was worth it lol
Fabulous job. It was great that you built every part from scratch. Your video is a joy to watch (3 years later), I'll bet the amp has brought you a lot of pleasure!!
Extraordinary job from a regular person. Very inspiring!
Thanks 👌
Really impressive job, especially with the "primitive" tools!! Sounds really nice too.
Thanks, glad you liked it!
You did an excellent job considering it's from scratch. Building from a kit is hard enough but to build your chassis from scratch and gather all the parts yourself proves your ambition. I would love to own that amp.
thanks! there's definitely something cool about doing everything part of the amp yourself.
There are so many 5E3 clones available and a bunch of kits. Makes sense because the 5E3 Deluxe sounds great, is versatile and a relatively simple circuit. Joe Les took it one step further and built from total scratch. Awesome and damn fine work!
Thanks! It’s definitely a great amp, I’m still playing it every day
Wow, very nice amp! I want to try to lacquering canvas over a cabinet like this for a super-old school look. We have a saying: "A good solder joint starts with a good mechanical joint." In this case, pull the wire or component lead through the solder eye, and bring it back to itself. Don't twist it. Pinch them together forming a nice parallel section of 1/8" at the eye. (Meaning, don't leave a big stub.) Then flow a good solder mass that encapsulates the entire interface. It should look like it was dipped in thick molten metal that formed a teardrop shape...no rough surfaces or voids. That takes HEAT on the ENTIRE joint. Use plenty of flux and LOWER temp tin-lead solder for best results. Also, thermal cycling causes a lot of expansion & contraction in conductive material...any metal. So, leaving a little extra "service loop" adds tremendous life to those solder joints. (That just means leaving some extra lead length to prevent them being too tight...not an actual loop.) Finally, solder joints are the highest failure mode in this sort of device...meaning they crap-out first! Joints that look good, but weren't heated fully are the enemy: A "cold solder joint." They work when new, but die over time. Before they go completely, you often see resistance changes & intermittency. Avoid them by following my advice above. Good job on this...rock on brother!
Very nice build. This video just popped up and I probably would have ignored it but when you mentioned Uncle Doug early on that was enough for me to watch it. Great work.
haha thanks glad you ended up liking it
Having re-built several old tube amplifiers, I am hugely impressed. Your attention to keeping it neat and simple looking, while being a complicated work of art is so beautiful. I really like your choice of wood finish instead of tolex. Nothing wrong with tolex, but your amazing routed fitted corners and natural wood grain is just Tops. Just an absolutely beautiful job, and it sounds wonderful.
Thank you, I appreciate it!!
@@joeles2738 Beautiful job Bro!
I give you praise for this build I love how raw and vintage this amp looks I loved how you built your chassis and cabinet this amps sounds better than some boutique 2000 dollar amps.
thank you! glad you like it
I have built a few guitars but never thought about a custom Amp. Thank you for the inspiration.
Nice, you should go for it!
Well done! Great effort. I liked how you started again on the chassis. That's the kind of thing that I do as something like that keeps me up at night. Also taking the build outside to the yard, yep, can relate again. Beautiful result, great stuff!
Thanks! Watching your amp build a while ago was actually one of the first things that gave me the idea to do my first build (a champ) now that I think about it. And yeah I am really glad I started over on that chassis haha
Great job! When I was your age, I didn’t have the knowledge and skillset you have. I would be very proud of the job you did. Keep up the good work!!
thank you!!
Excellent, excellent, excellent job. It shows you are a resourceful young man. This will be a stepping stone to future builds. Good for you. Cheers🙂
Thanks! There definitely will be more builds in the future
Sultans of Swing - the perfect chord prog to test a DIY amp 🙂
Thank you for the video. you did a great job, I love how it turned it out.
Thanks!! Glad you enjoyed the video
I wish I had your woodworking skills, you did really good man, that amp looks beautiful.
Thanks! Glad you liked it
I like it when you switch channels and the camera/started shaking. Loved everything from start to finish!!
Glad you liked the video! Thanks for the comment
Joe that was crazy good for a 1st build. Thanks for applying skill and labor to something you love. Was a good watch sir. I enjoyed it.
I'm glad you enjoyed it! This actually wasn't my first build; I built a pretty rough-around-the-edges fender champ a couple years ago, but this was my first time really going all in and trying to make it look really good.
Thanks so much for sharing that. I’m good on electronics, but the woodworking and the metalworking…I would never be able to do but it’s great to see someone else do it! Sounds great. Also nice you update below with changes (baffle, tube sockets, etc.). Thanks so much!
Nice work. And good commentary too. So many people say the same thing 3 or 4 times in a row on these kind of videos but yours is concise and clear.
Thanks for taking the time to document your build. It sounds great.
Thanks, I'm glad you enjoyed it!
Your video is very good. You should make more such amplifier building videos
Maybe I will 👀
Amazing job! I ended up here because I wanted to build my own tube amp. I have a huge box NOS tube from the 60/70's and I really wanted to make a few tube amps with them. I was ready to be COMPLETELY overwhelmed, but dag gummit, you made it look so clean and doable, I am no longer scared of trying it. Thank you so much for that! Well done!!!
I like the natural wood way better than the tweed.
Me too!! And waaay less work
sick job on the metal-,wood- and electric work. looks like it was a lot of fun in the workshop.
Thanks! I definitely did enjoy the process.
Great job, young man, very nice workmanship... Only thing I see that I would mention is the output transformer should be at a 90° to the power transformer (so 1/4 turn) to cancel a magnetic field for noise canceling purposes look it up on the channels you listed. It sounds good however and I wouldn't worry much about it, but something tells me you will be doing more of this. Knowledge is power, carry-on! ✌️👍
amplifier clear sound cabinet box nice and clean and one thing I love is the vintage design good job sir.
thanks!
I went two electronic School and have never built an amp. I am a big failure . I am very impressed with what you have done here.
Thanks for taking the time to show this.
You’re welcome! Thanks for the comment
Well done- looks great. I especially like the exposed finger joints. Has a vintage look to it.
Thanks! I’m glad I decided not to cover it.
Top marks for using the "Template" and "well done" on the cabinet. I can imagine it in shrinking black gloss wood paint with laquer for some reason. The bigger cab dimensions are a great idea, I had a Blues dlux which I gutted and kept transformers and chassis and tweed cab(stained with shellac) the cab is bigger than a 59 type, put a Jensen P12Q in it and handwired an improvised an ab763 to run 2 6L6s with proper valve reverb simple bass/mid/treble. Keep it all simple as poss. Good stuff!
I loved this video. It inspired me to do the same while convalescing from heart surgery. I haven't yet started an amp build project since short term disability doesn't pay much, but I hope to in the future. Thanks Joe, this was awesome.
Thank you, that’s great to hear! Good luck on your project!
Rob Robinette + Uncle Doug is a winning combination, thanks to them I haven't blown myself up (yet). I've just finished a 5F6a head with a few of RR's mods (including the stealth speaker!) - his site is a brilliant resource, the startup & troubleshooting sections are invaluable. The layouts are great too - I've built a few amps following them and haven't yet found any errors (unlike a few others I could mention😄).
yep, both of those resources have been soooo valuable for me as well. I remember when I first had the idea of building a guitar amp a few years ago I had no idea what was involved, but Rob's site was great and I successfully built a working champ. All of the online forums have been great too.
@@joeles2738 My first was a Blackface Deluxe Reverb & Rob was my bible... though credit where credit's due - Uncle D was my God😄
@@acooper8910 wow that's pretty ambitious doing a deluxe reverb as a first build! How did it go?
@@joeles2738 The initial plan was for a JTM45 but the chassis was massively delayed - I got impatient & decided to do the DR while I was waiting. Obviously a big learning curve but I managed a working (& humless) amp within a couple of weeks. After I'd built a few more amps (and watched way more Uncle D videos) I went back to it and did a complete rewire cos it was a bit of a rat's nest.
@@acooper8910 nice 👌
Great build dude! That G12Q speaker really impressed me. For me it was the icing on the cake of this build. I love how I can get lovely big rich cleans playing normally, but if I dig in, the speaker just EXPLODES. A lot of people hate early speaker breakup but for me its fantastic as it really adds that "melting tweed" vibe at usable volumes.
I think the best advice you gave was that you viewed other builders sites and TH-cam channels, and learned a lot about what and what nHhstarted ordering anything. I also liked 🎉that you left the pine cabinet, and just poly or clear coated it, looks much nicer and more custom than had you covered it in tolex like everyone else does. Sounded good too, really nice job!
Thanks! Glad you like it
Great job on the video as well as the amp! Thanks for sharing with us!
Glad you liked it 👌
FANTASTIC WORK! I built a little 4-watt tube amp some years ago, so I know of the excitement involved.
Good job.
Yeah it’s super exciting! Thanks for the comment
Nice job Joe! You should consider a job in woodworking. You've got a lot of determination to build that with such humble tools.
Thanks 🌝
very nice work fella! thanks for showing this fine piece
of kit ,cool clean tone, with nice and punchy overdriven
sounds, admirable result ,
glad you like it! thanks for the comment
Wow dude...I was mesmerized watching this video. Hats off to you sir...nice job!
thanks!
This is really nice work. The only thing that lets it down cosmetically is the grill. That would be easy enough to change, given how it's attached. Some vintage grill weave material would be for more in keeping with the rest of the style and would set it off perfectly, I think. In any case, the box and chassis are gorgeous and sound the part for sure!
Dude... what you did is completely insane... dang!
Thanks!! Glad you liked it
amazing! I like the fact you made your own aluminium cabinet enclosure as well as wiring it and doing the woodworking, sounds good as well.
thanks! doing the chassis from scratch definitely added a lot of work to the project but it's cool having an end result that's 100% homemade.
Wow. Just wow. I really want to start building one and seeing this has given me the inspiration to do it. Luckily I have a lot of tools from 30 years of work but I will be please if mine is half as good as this.
This is an awesome build Joe!
Glad you liked it 👌
Awesome job! A piece of wood under the turret board while you're drilling it will make it easier to drill the holes.
It looks beautiful and sounds cool
thanks!
Love the fact that you utilized a turret board, rather than an eyelet board.
yeah, I've never used an eyelet board before but I kinda feel like turret boards would be easier to solder to. Also I feel like it would be kinda tough to build an eyelet board yourself
@@joeles2738 Eyelet board are pretty easy to make, I use 4mm centre hole nickel plated eyelets, as used in leatherwork. They take solder really well. I put them into 2mm paxolin, or whatever the equivalent is called in the USA. It works out much cheaper, and to me look neater than turrets.
@@chrisbarrett5132 oh nice! I think I still prefer the look and toughness of a fiberglass turret board but I guess it’s just a personal preference thing
If you anneal your aluminum with a propane torch at the lines you want to bend it will make it bend like butter. I was a toolmaker for 30 years with amp work as a sideline so it gave me a good knowledge of metal work for chassis building.
Thanks, that's a great idea! I'll probably give that a try on my next chassis
fun build! I used a beehive kit from Tractor Supply to build my cabs, head and speaker cabs...worked great and saved huge time with limited tools and carp. skills....just say'n
That’s a cool idea, I’ve seen lots of cabs and heads made out various repurposed stuff and I’ve always thought they have a pretty cool look
Yep the deep beehive box is almost identical size to the 5e3 cab. I did one and turned the boards inside out so the handles were on the inside. It’s convenient and finger joined too though Next time I’ll buy the wood and hand make the joints.
@@davidsimpson3380 I've done a few since using The Behive Boxes...a nice 5f1 head and a mojo stidio 1 head. My routing work is improving! I might work on finger joints next...though the cabs after tolex applied no one could tell a difference. Uncle Doug has produced some awsome videos on building cabs....those inspired me, not to mention the cost on premade cabs.
Beautiful tone, beautiful amp. Well done!
thanks!!
Very nice original build on an OG classic. Great work.
thank you!
The tone is clearly in the hand-wiring and in the Chibson pick! ;)
I can only imagine how good it would sound if I had used period-correct 70
year old vintage wire
Great video and audio....you explained everything well.....good job...nice work.
Glad you liked it!
Joe, great job! Not only was your planning and execution of the project impeccable, but your video showing all the steps is also exemplary. Keep going!
Thanks!
Really nice, I'm considering building one myself and your attempt to build your own chassis made me decide too also build that myself.
Nice! Building a chassis from scratch is definitely kind of a pain but it’s cool having a final product that’s 100% homemade
Really nice build!! Great sound too!!!
@@jedishaw6771 glad ya liked it 👌
Nice work. Also, plenty of room in that cab for a reverb tank if you ever wanted to… lovely
Very nice job on the amp. I like it!! 👍🏻👍🏻
thanks!
We can see how it is moving the air in the room. Great job!
thank you! I think that was just my phone vibrating haha
Nice job. Lots of very good tips in there, thanks very much for posting.
You're welcome! I'm glad you found it helpful.
I have built 3 amps now two 5e3s and a 6g3 head. The head cab and one of the 5e3 cabs I built too and 212 cab for the head. Lots of fun! 6g3 is a Dovetail Cab.
cool!
OMG, so impressed, super job all by hand using normal tools, big thanks for the inspiration, there’s hope :)
thanks, glad you liked it!
I'm in the midst of building a little bigger amp with reverb and tremolo. Following this one, I plan to build a 5E3 clone as well. Your video was very helpful for my planning.
Good luck; I'm glad this was helpful!
Lovely work!
Thanks I appreciate it!
This is an incredible build. When you can, you might want to touch up your tube socket soldering. You need more heat on the joint so the solder reflows properly on the socket leads. Many of the those fillets are cold. They could fail in time unless you've got smooth solder between the wire lead and socket pins.
Respect to the people like you, I wouldn’t be able to do it, so many jobs in one product made by one person👍👍👍envy🤷♂️🤦♂️🥃🥃from🇨🇿
thanks!
This was amazing. Bless you for doing this for your community!!! I am a new subscriber!!!
Thanks for subscribing! Glad you liked the video
So cool!! Looks fabulous, sounds fabulous!
Thanks!
I would pay big money for your amps. Made with perfection and heart
Thanks!! I actually have 5F2A Princeton clone that I built for sale on reverb currently: reverb.com/item/58129111-hand-built-fender-5f2a-princeton?bk=eyJhbGciOiJIUzI1NiJ9.eyJqdGkiOiJhNDEzZjY5YS0zNWQwLTQ5NTUtODFkZC0xNjM0YjU5NWUwNjQiLCJpYXQiOjE2NjA0MzgzODMsInVzZXJfaWQiOiI0MjAwNzg0Iiwic2Vzc2lvbl9pZCI6IjVkMWVhNzZlLTE0NTUtNGY0OC1hOWUzLTY0ODFjNDIyNGU2ZSIsImNvb2tpZV9pZCI6IjBhNWQzOTc5LTllMzItNDgwYy1iNDc1LTgwMmU5ZGU3NDcxNCIsInByb2R1Y3RfaWQiOiI1ODEyOTExMSIsInNvdXJjZSI6Ik5PTkUifQ.g93AAznxXTO29I19yVwOpwr0tpaxllVZU75jsphv120
Congratulations on your first and very nice build!
You accomplished exactly what I wanted to do with my build by providing a very detailed description of every step. I tried to video mine and bailed about half way in because I would get wrapped up on the build and forget to record. The time I was spending to go back and reproduce a step or edit a screw up wasn't worth it to me. I'm not a patient person and the build really pushed my buttons a few times.
I don't think the general viewer is aware of how much time is required to produce a quality, comprehensive amp video build.
Like yours, my first amp was my own design. I started with a flat sheet of scrap aluminum picked from the floor of a trailer shop. Every component and screw was hand picked. It was expensive in the end but worth it. The completed amp is a 5F2A with a C channel horizontal chassis in a 1941 Majestic console record player / radio cabinet with a 12" Jensen C12Q. I wanted different and that's what I have and I couldn't be more pleased with it.
I look forward to your next build and thank you for sharing your very nice build.
Nice! I appreciate it and congrats on the successful build
Good job ! The RobRob Deluxe is my next project. All the parts are ready and waiting. I just need time.
Thank you! Good luck with your build!
Impressive. Nice documentary.. Thanks.
you're welcome, thanks for the comment!
Love the look and sound of your Amp, great work
thanks! glad you like it
You’re pretty talented my friend… Thanks for showing us your skills. Good job. 👍🏼
Had no idea this was even an option. I’ve been looking at getting a tweed delux but didn’t want to shell out money for a new one. This is a great option if you have the skills already.
this is awesome, great project. soldering on the stakes is a new technique to me, it's kind of a hack around a PCB.
Nice job! I made a similar amp, a tweed champ, from scratch , but I used 16 gauge steel for the chassis. I didn’t have any trouble cutting it with my jigsaw but bending it was really hard!
Yeah I bet, bending this definitely wasn't easy even with aluminum
That's excellent work, you should be really proud of yourself. Playing through something that you worked hard over, and made yourself must be really satisfying. Just 2 personal preferences on my part, I might have been tempted to make the amp as a separate head and cabinet if you had the wood, make it more modular and can swap out components more easily. And at about 24:25, you pull on your guitar lead a little and risk either damaging the input jack, or pulling the whole amp forward onto its face. This is probably why most amps have their input on the front so that if enough pressure is exerted you just pull the cable right out of the jack. Plus at a glance you can see what the volume, gain etc. is currently at without standing right over the amp. That aside, I'm impressed by your efforts here, well played. 👍
Very nice construction work. I have also really enjoyed building tube equipment this past year. Make sure the solder joints are really hot and fully melted.
Thanks, and yep you definitely have to be careful to avoid cold joints
Cool! Getting ready to build a kit amplifier from stew Mac so this was really helpful!
Nice, glad it helped!
Very nice job and a well done video! Nobody is perfect, some are just more skilled at concealing their mistakes. Your video could serve as an excellent tutorial for newbies!
REALLY nice job! Thanks for filming. I'm onto building the rob rob deluxe 5e3.
Thanks, and good luck!!
Beautiful!!! And it sounds great as well!!!
I’m glad you like it! Thanks for the comment
Very Impressed .. it turned out great and as I read .. you've already made upgrades and improvements. I think I too would go with a the natural finish if I had spent that the timed to build the cab! I would be such a noob with the electronics.. you've obviously got a good handle on what you're doing and taking a sensible approach to testing as you go along. Kudos!!
Thank you! I also really like the natural wood look. Although it does probably make it a little less durable.
Respect to ya. Definitely a fun process. I've never built my own chassis but have drilled all the holes per my own layout. Built a 5 watt tweed princeton circuit in the layout if a Marshall head. Fun stuff. The hand pick had me rollin
Nice! Glad you enjoyed
Beautiful! I want it !
Well I am planning on building a couple 5f2a Princetons soon that I’ll be selling 👀
Beautiful work and the design is spot on ! Congrats on a well built amp !
nice build, currently building a 5D3
Nice! Is that the deluxe model that came out before the 5e3?
@@joeles2738 yeah, it looks like there were a couple of capacitor changes between the two models.
@@cfl941 cool
Great job. The end product looks really nice and I like the natural wood finish.
Thanks!
excellent job
thank you!
Joe, nice cab build, looks great. Amp sounds fantastic. Great job!
Thanks!!
Looks great dude! Well done
Thanks!
Very nice job, great sounds, well done to you