Followed the install with the exception of connecting the wires after installing the first speaker was able to install the other 3 in under an hour. Replaced the OEM 61/2 in with JBL of the same size. Currently using a Kenwood 393 no amplifiers or sub woofer in my 2014 sportage vast improvement. Please experience the install before criticizing. Thanks for the video
as a retired electrical engineer, i was watching through my fingers.! please dont follow this video first point always SOLDER any cable joints then use heat shrink and then insulating tape .i would not have joined to the original speaker BARE cable .you can purchase aftermarket connectors or you can chop off the speaker conectors [always leave enough cable on the connector so that you can resolder back if you are not happy with the sound of your new speakers .dont use scotch locks or terminal block always solder .you can remove the factory conectors in the door to the speakers and solder directley to the wiring loom and then heat shrink .as the speaker for the kia and hyundai tucson are 16.5 PLEASEN NOTE that a 16.5 speaker will not fit properley i leaves a gap so you will need to purchase 4 after market speaker pods because the speakers are raised from the door the speakers dont fit flat to the door you need the correct pods to bring the speakers to the door card this improves sound and stopps vibration .the speaker pods cost around £18 per pair but they are hard to get hold of .take your time make sure that the speakers are wired correctly . you can check this with a battery there are youtube vids to show you how to do this even if you use high-end speaker you wont notice a massive improvement in the quality of sound due to the limitation of the original head unit [the original Hyundai Tucson [a 55 plate ] was a lot easier to work on i added 4 hertz speaker and a Kenwood under seat sub and a mid-range head unit when my original CD player failed out of warranty .its not that easy with new cars as the head unit controls more things that just music [it can be changed but your looking at £100s and its not an easy job] kia and hyundai are the same company .
I was wondering if it was a tight seal and was considering silicon or a gasket. I think I'll go for the replacement speaker adapters and go from there. Good suggestions.
Very clear vid showing how to remove stock speakers and caution on wiring. Did not realize removing stock speakers is so simple, but will permanently destroy the speakers!!
This is not the first time i saw ur video. At first i just scoll on youtube all about sportage. And now i have an idea to plasti dip my interior door trim. Is it easy to knock them off? It has dual color, black and grey. I just want to plasti dip the grey one. But i don't have idea to remove the foam etc
Yo que vos no cambiaria los speakers originales, son Harman Hardon, por lo menos en mi Kia Sportage son de esa marca y son lo mejor del mercado, suenan una locura. Le puse el estereo de 9" de Kia y los tengo ecualizados y suena muy bien, sin quejas
2017 Kia Sportage use a tweeter in upper frame and woofer below - looks like you replaced the woofer with a full frequency speaker? There's a crossover somewhere - are you getting upper frequencies through your new speaker?
Yes, you will get some upper frequencies though aa full range speaker in the lower section. However it will not be annoying. Also the original speakers did not have any kind of filter whtasoever and passed high frequencies as distortion. Replacing the speakers will give much better sound anyway.
Hey Rob- thank you for the video. I have an issue though. I recently bought a sport model and have the glowing lights in the front doors where I want the replacement speakers. If I drill into the walls surrounding the speaker in afraid I'll ruin the mood lights. Not that it's a terribly big issue if I do burin keeping in mind a possible resale situation down the road. What do I do in this case? Thank you!!
HI , does the 4 screw holding the speaker good ? i'm afraid it will be lose after a while because the way you drilled the hole is so weak , is that right ?
if you purchase the MDF special pods available from Amazon [cost around £19 per pair [please note that even though the advert says that the pods will fit the rear door they will also fit the front doors too.they replace the original speaker bringing the speaker back to the inside of the door [just like the original speaker with the option for you to install any 6.5-inch speaker of your choice .if you use the speaker pods and the original screws you will get a firm fit because the plastic innner door cards are soft plastic and will grip the screws very tightley so dont worry .use a good brand of aftermarket speakers and fit them to the MDF pods when purchasing speakers make sure that they will be okay with your low powered factory fit head unit .i have purchased JBL speakers that say that they are okay with original low powered head units
Hi. Recently I purchased a Kia Venga 18/02/2016 and the quality sound in rear seats is terrible. But in general is not bad. Maybe I will replace the rear speakers. El vídeo es de mucha ayuda. Thanks a lot.
Nice explain. But, when I connect my speaker there is no sound, even not when I change the cables from + and -. My speaker has 4 connections on it (2 plus 2 minus) but I think that is not the problem. The old speaker I removed worked, so what I’m doing wrong 😂
For kia picanto it is pretty much the same but the door panel removal is somewhat different. There are some good photos on kia forums dot com so if you google for kia picanto speaker replacement you will find what you are looking for. Succes.
Hey Rob- thank you for the video. I have an issue though. I recently bought a sport model and have the glowing lights in the front doors where I want the replacement speakers. If I drill into the walls surrounding the speaker i am afraid I'll ruin the mood lights. Not that it's a terribly big issue if I do but i am keeping in mind a possible resale situation down the road. What do I do in this case? Thank you!!
Hallo Rob . Heb je deze speakers al de 4 deuren gemonteerd ? En wat heb je gedaan met de tweeters in de voordeuren? Maar waar ik het meest benieuwd naar ben is , Hou klinken ze is het een groot verschil ? En verder erg duidelijk allemaal top gedaan .
Pieter Makrakis Ja ik heb ze in alle 4 de deuren. Ik heb de tweeters gewoon laten zitten. Ik heb eerste de voordeuren gedaan. Als je daarna de speakers 'balanceert' naar de oude die nog achter zitten is het echt een wereld van verschil. De oude speakers waren echt doffe elllende vergeleken bij de nieuwe. En dan zijn die van JVC nog niet eens de allerbeste. Ik heb de JVC speakers voor EUR 28,- per set op internet gekocht. Voor EUR 54,- ben ik superblij met het veel betere geluid.
Goed om te horen Rob , nou dan ga ik maar speakers bestellen 😎 en dit weekend maar eens beginnen , ik zal je video , nog wel vaak moeten bekijken 😃 , nog 1 vraagje ik heb een pioneer Avic f930bt radio in de kia zitten . Daar zit een moset versterker in met 4x50 watt is dat genoeg denk je voor de speakers ? Of moet ik er nog een versterker inbouwen goed 2 vragen dus hahaha , en wat bedoel je met je heb de tweeters laten zitten die van de Kia ? Heb je die wel aan gesloten ? Wat een verhaal he 😃 Mvg. Pieter
Pieter Makrakis Tja of dat voldoende is, dat is erg persoonlijk. Voor mij in ieder geval wel (heb een Witson systeem ingebouwd). Er zijn echter ook mensen die hebben aan 4x1000W nog niet genoeg. Ik zou het gewoon eerst eens porberen en kijken of je het zelf goed vind. Kun je altijd nog een versterker of subwoofer oid inbouwen. Ik heb gewoon de originele tweeters van Kia laten zitten en aangesloten gehouden. Ik zie geen reden om ze af te koppelen. Net dat hele kleine beetje hoog op die plaats geeft ook wel weer een mooi ruimtelijk effect vind ik zelf. Mvg Rob
PLEASE... for the love of god do not do this to your vehicle. This is NOT the proper way to install speakers. You do NOT cut the tinsel leads on the old speakers, or cut the surround, you don’t ruin the old speaker at all!!!! Drill out the rivers and get an adapter for the speaker size as well as the wire connector. This is the worst way to install speakers.
Lol this is such a ghetto way of hooking up your speakers. Mdf spacers would make the sound better, solder your wires. Don't just use tape. And you don't need to rip out your old speaker just drill rivets or unscrew it!
What the heck did I just watch?? Why not just unscrew the stock speakers then replace with new ones with aftermarket connector? No need to do a hack job like you just did
In kia the speakers are not screwed. Also you need the rings as adapter to install the speakers on. This is the easiest way. There are other ways also better ways according to some...
Hahaha nee hoef ook niet zoveel hoor als het maar beter klinkt dan de fabrieks speakers . Ik laat je weten hoe ik ze vind als ik ze er in heb zitten . Mvg Pieter
Yes, you are right, there is allways a better way. Damping should improve the sound. However it is not easy to attach damping behind the panel. There are some youtube movies to show you. However, this movie is abould speaker replacement and not damping improvement. I do not agree on the MDF. The panel and ring are stiff enough for regular power speakers and they do not vibrate. I should reuse the existing rings.
mal trabajo , si te das cuenta cuando pongas el panel de la puerta va chocar con el parlante que ha quedado mas alto que el original. se puede mejorar ese trabajo.
Yes as per text at 0.09min in the video: rear door. For thee front speakers, the plastic covers obove the tweater have t be removed and the panels have lone screw less.
The channels name (hamada alraie) he stole my video too .I think here channel close by youtube .Because i told very one he stolen video. and i send the channels link to you before
This guy is a hack - lol I was laughing and cringing through the entire video. Oh and the "IMPORTANT" part was totally pointless with his method and pointless unless you are rewiring all the way back to the stereo. Seriously I would not use this guy as someone to learn from. Will his method work? Yeah Will is last? Doubtful.
I agree the jvc are not the best but much better than the kia. They are worth the money however. Of course you can use the same method for the high end speakers you prefer. Hope you enjoyed watching my video and it helps you installing the speakers of your own choise. The video shows the installation and is not an advertise for the speakers.
Who else cringed when he cut the speaker lol good job brotha 👍
Followed the install with the exception of connecting the wires after installing the first speaker was able to install the other 3 in under an hour. Replaced the OEM 61/2 in with JBL of the same size. Currently using a Kenwood 393 no amplifiers or sub woofer in my 2014 sportage vast improvement. Please experience the install before criticizing. Thanks for the video
8:15 Test speaker before fastening down door to prevent cursing later.
😅
I came here for the awarding winning video footage of the door panel removal. Rob O delivered! Thanks for putting this one together.
as a retired electrical engineer, i was watching through my fingers.! please dont follow this video first point always SOLDER any cable joints then use heat shrink and then insulating tape .i would not have joined to the original speaker BARE cable .you can purchase aftermarket connectors or you can chop off the speaker conectors [always leave enough cable on the connector so that you can resolder back if you are not happy with the sound of your new speakers .dont use scotch locks or terminal block always solder .you can remove the factory conectors in the door to the speakers and solder directley to the wiring loom and then heat shrink .as the speaker for the kia and hyundai tucson are 16.5 PLEASEN NOTE that a 16.5 speaker will not fit properley i leaves a gap so you will need to purchase 4 after market speaker pods because the speakers are raised from the door the speakers dont fit flat to the door you need the correct pods to bring the speakers to the door card this improves sound and stopps vibration .the speaker pods cost around £18 per pair but they are hard to get hold of .take your time make sure that the speakers are wired correctly . you can check this with a battery there are youtube vids to show you how to do this even if you use high-end speaker you wont notice a massive improvement in the quality of sound due to the limitation of the original head unit [the original Hyundai Tucson [a 55 plate ] was a lot easier to work on i added 4 hertz speaker and a Kenwood under seat sub and a mid-range head unit when my original CD player failed out of warranty .its not that easy with new cars as the head unit controls more things that just music [it can be changed but your looking at £100s and its not an easy job] kia and hyundai are the same company .
Tony Beer Yes, you are right. Soldering is a better option and i advise to solder if some has the possibility to do so.
I was wondering if it was a tight seal and was considering silicon or a gasket. I think I'll go for the replacement speaker adapters and go from there. Good suggestions.
would drilling out the rivets be a better option? just curious i have the same issue and im not sure how i feel about cutting this out.
Although this is considered a bodge job, I followed these steps and it worked perfectly. Took me 10 minutes per speaker to swap. FairPlay
I did my Sportage at the weekend using a similar technique. I soldered the wires onto the existing tabes. The Infinitys sound excellent!
Thank you very much, I was going to buy brackets but after watching your video I saw how easy it is to adapt the new speaker.
hello thank you for telling me how you found the difference on the most and least cut wires.
thanks in advance
What size bit did you use to drill the holes? Were those the screws that came with speakers or you purchased diff ones?
OMG, KIA Speaker Engineers should cry, why you broke these Original Speakers?
Thank you. Followed your steps and was done in 10 minutes.
Not bad. He used the existing speaker as a bracket. Only thing I would have done is solder and heat shrink. Thanks for the vid.
What is the car model sir? Is it fit for sportage 2012 model?
This is exactly how not to do it I'm a woman and even I know this I've never seen anyone cut out a speaker wow just wow
Can someone please give me the diameter of the soft thin edge foam he cut out? I need to replace my torn ones but not sure the size to pick... please
Very clear vid showing how to remove stock speakers and caution on wiring. Did not realize removing stock speakers is so simple, but will permanently destroy the speakers!!
please dont follow this video its wrong [retired electrical engineer]
What suggestion do you have for improvements or changes in procedure?
Yes i got it... now i wanna change the break pads so i can cut the rim in to 2 half. Thanks for the video.
Hahaha
This is not the first time i saw ur video. At first i just scoll on youtube all about sportage. And now i have an idea to plasti dip my interior door trim.
Is it easy to knock them off? It has dual color, black and grey. I just want to plasti dip the grey one. But i don't have idea to remove the foam etc
Super happy that I watched this video. Everything went perfectly! Thanks.
tengo una kia sportage 2011 que bocina me recomienda que compre para reemplazar las originales y hacerlo como usted lo hizo
Yo que vos no cambiaria los speakers originales, son Harman Hardon, por lo menos en mi Kia Sportage son de esa marca y son lo mejor del mercado, suenan una locura. Le puse el estereo de 9" de Kia y los tengo ecualizados y suena muy bien, sin quejas
What size are the speakers for all speakers on the kia sportage 200-7,8,9
I do not know for the older kia sportages..
is it the same for hyundai tucson? water is getting inside my car through the door
I learned something new... the best video to replace speakers!!
6:00 solder then heat shrink tubing.
i agree
Or at least individually tape
Thx for video. Can i learn that how many watts are original of kia and your new speaker?
old speakers were 20 watt peak new speakers 50 watt peak
2017 Kia Sportage use a tweeter in upper frame and woofer below - looks like you replaced the woofer with a full frequency speaker? There's a crossover somewhere - are you getting upper frequencies through your new speaker?
Yes, you will get some upper frequencies though aa full range speaker in the lower section. However it will not be annoying. Also the original speakers did not have any kind of filter whtasoever and passed high frequencies as distortion. Replacing the speakers will give much better sound anyway.
Hoi Rob . Nou was vandaag een mooie dag om speakers in te bouwen 👍🏻 is gelukt 😃 klinkt als een dijk . Bedankt voor je duidelijke uitleg 👍🏻👍🏻👍🏻👍🏻👍🏻.
Pieter Makrakis Ok great. Thanks for the reply.
Hey Rob- thank you for the video. I have an issue though. I recently bought a sport model and have the glowing lights in the front doors where I want the replacement speakers. If I drill into the walls surrounding the speaker in afraid I'll ruin the mood lights. Not that it's a terribly big issue if I do burin keeping in mind a possible resale situation down the road. What do I do in this case? Thank you!!
Where do i buy speaker? I can't seen to find trustworthy sites and with midrange price. My speaker is blown. Kia sportage 2014
Can you google for 165 car speaker? It should give some results.
HI , does the 4 screw holding the speaker good ? i'm afraid it will be lose after a while because the way you drilled the hole is so weak , is that right ?
if you purchase the MDF special pods available from Amazon [cost around £19 per pair [please note that even though the advert says that the pods will fit the rear door they will also fit the front doors too.they replace the original speaker bringing the speaker back to the inside of the door [just like the original speaker with the option for you to install any 6.5-inch speaker of your choice .if you use the speaker pods and the original screws you will get a firm fit because the plastic innner door cards are soft plastic and will grip the screws very tightley so dont worry .use a good brand of aftermarket speakers and fit them to the MDF pods when purchasing speakers make sure that they will be okay with your low powered factory fit head unit .i have purchased JBL speakers that say that they are okay with original low powered head units
First rate video, showed me exactly what I needed to know!
Thanks for the video! I'm hoping to install a new door handle by removing the panel on my Soul.
brandiann09 i am sure this video would help you understand to remove the door panel. Succes!
Hi. Recently I purchased a Kia Venga 18/02/2016 and the quality sound in rear seats is terrible. But in general is not bad.
Maybe I will replace the rear speakers.
El vídeo es de mucha ayuda.
Thanks a lot.
Thanks dude, you just saved me some frustration.
Pls tell me you did not do this
Nice explain. But, when I connect my speaker there is no sound, even not when I change the cables from + and -. My speaker has 4 connections on it (2 plus 2 minus) but I think that is not the problem.
The old speaker I removed worked, so what I’m doing wrong 😂
Do I need to connect all electricals to the door or only speaker for testing? I left the door cover off when testing
@@dutchdude123 you can leave the cover off for testing. You can also wait mounting the speaker and only first connect the cables and test
@@robo694 fixed it , demolished the inner connector so I cut the wires en reconnected and it works. Tnx
Really good video!!! Have you the video of the front doors? I want to change the 4 speakers. Thanks
hay did u do it ?
Gracias por el video, me ayudo mucho. Thanks
Bro ya lo hiciste ? Si mejoro ? No quedaron ruidos raros o sonajientos ?
What year sportage is this?
This is model 2012
You should never be allowed near a car again. Every part of this video between taking that knife out and replacing the door cards is 100% WRONG.
i agree
does this work for the kia picanto?
For kia picanto it is pretty much the same but the door panel removal is somewhat different. There are some good photos on kia forums dot com so if you google for kia picanto speaker replacement you will find what you are looking for. Succes.
+Rob O Thanks!
No problem.
WHAT IN THE HELL DID I JUST WATCH?? JESUS CHRIST, ' THE BUTCHER!!'
its the best way to re use the speaker bracket, long time a go u could just in screw the speaker from the bracket now u have to hack and slash
good trick. how about the front doors, is it the same? thanks
Hey Rob- thank you for the video. I have an issue though. I recently bought a sport model and have the glowing lights in the front doors where I want the replacement speakers. If I drill into the walls surrounding the speaker i am afraid I'll ruin the mood lights. Not that it's a terribly big issue if I do but i am keeping in mind a possible resale situation down the road. What do I do in this case? Thank you!!
I would not ruin the lights and keep the value for resale.
+Rob O
So how can i go about putting the after market speakers in? do you have any suggestions?
+Rob O
Thank you for the reply btw!
What is the size of the speaker
6.5 inch or 165 mm
This also works for 2008/2009 Kia rio lx door panels/speakers.
What about a 2007 Kia Rio5 ?
Well done and thank you very much for your excellent video
Front passenger wire color Red(+), Blue(-) ?
Red - Blue +
What size speaker does that frame fit?
A size 6.5 inch or 165 mm dia
Why cut the speaker ....
Hallo Rob . Heb je deze speakers al de 4 deuren gemonteerd ? En wat heb je gedaan met de tweeters in de voordeuren? Maar waar ik het meest benieuwd naar ben is , Hou klinken ze is het een groot verschil ? En verder erg duidelijk allemaal top gedaan .
Pieter Makrakis Ja ik heb ze in alle 4 de deuren. Ik heb de tweeters gewoon laten zitten. Ik heb eerste de voordeuren gedaan. Als je daarna de speakers 'balanceert' naar de oude die nog achter zitten is het echt een wereld van verschil. De oude speakers waren echt doffe elllende vergeleken bij de nieuwe. En dan zijn die van JVC nog niet eens de allerbeste. Ik heb de JVC speakers voor EUR 28,- per set op internet gekocht. Voor EUR 54,- ben ik superblij met het veel betere geluid.
I did the same for years. But now charger the cost of adapter at custumer pockets .
is this guy for real !!!! the propper adaptors are only £10 a pair
This video is very much appreciated sir!
Good tutorial mate. keep up the good work. :-)
Thanks
why......really why did you cut ?. you could simply unscrew the old one and replace with a new one with brand new brackets.
The kia souls brackets are riveted in. Drilling and replacing the rivets complicates it more than a driveway quick fix.
this door panel looks close my 2017 forte 5 sx looking at 6.5 subs at 3 inchs deep
Goed om te horen Rob , nou dan ga ik maar speakers bestellen 😎 en dit weekend maar eens beginnen , ik zal je video , nog wel vaak moeten bekijken 😃 , nog 1 vraagje ik heb een pioneer Avic f930bt radio in de kia zitten . Daar zit een moset versterker in met 4x50 watt is dat genoeg denk je voor de speakers ? Of moet ik er nog een versterker inbouwen goed 2 vragen dus hahaha , en wat bedoel je met je heb de tweeters laten zitten die van de Kia ? Heb je die wel aan gesloten ? Wat een verhaal he 😃
Mvg. Pieter
Pieter Makrakis Tja of dat voldoende is, dat is erg persoonlijk. Voor mij in ieder geval wel (heb een Witson systeem ingebouwd). Er zijn echter ook mensen die hebben aan 4x1000W nog niet genoeg. Ik zou het gewoon eerst eens porberen en kijken of je het zelf goed vind. Kun je altijd nog een versterker of subwoofer oid inbouwen.
Ik heb gewoon de originele tweeters van Kia laten zitten en aangesloten gehouden. Ik zie geen reden om ze af te koppelen. Net dat hele kleine beetje hoog op die plaats geeft ook wel weer een mooi ruimtelijk effect vind ik zelf.
Mvg Rob
The front passenger red is + and blue should be -
Yes, I also found the red (+) and the Blue (-)
Where did you get that bag of yellow gadgets?
it is on Aliexpress, search for item "32707501981" or "car radio removal tool" in the search bar.
This worked perfectly! Thanks for the video!
hack job...uggg...TY for the vid..this is what I don not want on my new car 2018 Soul..
This is horrible.. exactly what not to do.
Thank you, very usefull
PLEASE... for the love of god do not do this to your vehicle. This is NOT the proper way to install speakers. You do NOT cut the tinsel leads on the old speakers, or cut the surround, you don’t ruin the old speaker at all!!!! Drill out the rivers and get an adapter for the speaker size as well as the wire connector. This is the worst way to install speakers.
Much bigger magnet on the old original speaker. I doubt the sound improved.
Lol this is such a ghetto way of hooking up your speakers. Mdf spacers would make the sound better, solder your wires. Don't just use tape. And you don't need to rip out your old speaker just drill rivets or unscrew it!
Very very useful video, thanks.
What the heck did I just watch?? Why not just unscrew the stock speakers then replace with new ones with aftermarket connector? No need to do a hack job like you just did
In kia the speakers are not screwed. Also you need the rings as adapter to install the speakers on. This is the easiest way. There are other ways also better ways according to some...
Hahaha nee hoef ook niet zoveel hoor als het maar beter klinkt dan de fabrieks speakers . Ik laat je weten hoe ik ze vind als ik ze er in heb zitten .
Mvg Pieter
Pieter Makrakis Super.
Este tipo es un bruto!
Whatt the f? 😂 You can remove the revits 😂
You shouldn't be doing how to's bro.. Like wow!!
Well, this is not good, first of all you should make a mdf pads for speaker, yse som damping mat ant other materials.
Yes, you are right, there is allways a better way. Damping should improve the sound. However it is not easy to attach damping behind the panel. There are some youtube movies to show you. However, this movie is abould speaker replacement and not damping improvement. I do not agree on the MDF. The panel and ring are stiff enough for regular power speakers and they do not vibrate. I should reuse the existing rings.
mal trabajo , si te das cuenta cuando pongas el panel de la puerta va chocar con el parlante que ha quedado mas alto que el original. se puede mejorar ese trabajo.
+Abraham Smith
tengo un poco de espacio
You are awesome. Thanks!!!
Thank you for you video man
Should have told us .... REAR DOOR ONLY !!!!!!
vtownboxingfan yes, see the text at 0.09min
Yes as per text at 0.09min in the video: rear door. For thee front speakers, the plastic covers obove the tweater have t be removed and the panels have lone screw less.
HI SOMEONE STOLEN YOUR VIDEO
Who did this ??
The channels name (hamada alraie) he stole my video too .I think here channel close by youtube .Because i told very one he stolen video. and i send the channels link to you before
Dahen Zana thanks, i will check.
Welcome sir
What the fu**?! Really?! 🔪🔈🚫 NO!! Folks, DO NOT do this to your poor car!!! 😮😭🤣
hahaha
This guy is a hack - lol I was laughing and cringing through the entire video. Oh and the "IMPORTANT" part was totally pointless with his method and pointless unless you are rewiring all the way back to the stereo. Seriously I would not use this guy as someone to learn from. Will his method work? Yeah Will is last? Doubtful.
ok. have nice day. bye
Same to you. Thanks.
What is going on here? He can remove the foam and screw it out... he should not be able to own a car or TH-cam
My front doors on my Dodge was easier than this.
daaaaamn, that hurts
Please nobody pay attention to this install 100% wrong obly do this if you want a worse sound than before...
Wtf
Kia instal shit speakers and you replace her with bigest shit speaker.
I agree the jvc are not the best but much better than the kia. They are worth the money however. Of course you can use the same method for the high end speakers you prefer. Hope you enjoyed watching my video and it helps you installing the speakers of your own choise. The video shows the installation and is not an advertise for the speakers.
Lol
what size or the new speakers
6.5inch