Hey man I literally would have gave up on my bike a long time ago if it weren’t for you, every problem I have I know you’ll have a video on it! Thankyou
Thanks for making this video. I had the problem where the chain was jammed in side the motor. I was able to get the chain unjammed with just my fingers. If it wasn't for you I'd probably have to bring my bike to the repair shop!
I like that 2x4 trick and hammer, Never thought of that really cool and simple thanks for that tidbit. I'm sure in the future I will need it, Nice video.
Thank you so much for taking the time to make this video I’m trying to figure this out and there’s plenty of information you gave on this video that I will use
Hello Hughes, my 50cc engine won’t start because it seems to have too much compression on the block. When I put the spark plug back on its place the engine becomes too heavy and not able to pedal the bike. When I take the spark plug out the engine runs nice and smooth by turning the back wheel around. What can I do?
BTW I've got another problem my gas when I turn the gas it keeps slipping g not sure how to fix it I out glue on gripper piece and plastic that turns I drilled hole for little pin to catch but it's still slipping
Question, I was riding my bike fine for like 6 miles to the beach, then I slowed down, turned the bike off to go up a bridge, went to start it again and when I let the clutch out and the wheel locked up. I had to back up to free the wheel, then it had trouble starting again, then after a couple times of it starting it wouldn’t start again, and the chain keeps getting looser and looser and I have no idea why because the chain is still on the sprockets and everything. Now my main problem is getting it running, I have fuel, 30:1 ration, spark, compression, and the clutch is activating fine and disengaging fine, and the wheel still sometime locks up when I peddling. I have checked everything I know to check, I am extremely stumped and have had 3 guys come over to help to look at it. No idea. Any advice?
Hey Boss the sprocket fits so well without the dust cap Sir can I just use the sProket as a dust cap or is there or will there be some unforeseen problems?? Thansk
Hey man thankyou for the video please try answering this question, is the problem tht I haven’t put oil and gas in it like if I just try to pedal without it in will tht stop it because no lubrication or is tht not a problem
My back tire barely moves when the clutch is engaged. It's pretty much stuck. It does move freely when I disengage the clutch. What do you think is my problem? Thanks.
What if I still can't get it to engage wouldnit be something wrong internally with my clutch the tire seems to move fine and the chains spin bit the clutch still seems to be locked up?
Ayy Hughes, I have a problem with my rear hub. I already set everything up, put the sprocket on and serviced the hub...but I had the 2 loose brake pads fall out and I couldn't figure out how to get them back in. I figured I didn't need them, put on the sprocket and called it good. I didn't know I needed to put the brake arm back on. Are those pads necessary? Edit: I actually went ahead and did everything you showed in the video. Now my only issue is the gap between the dust cover and the bearing... My bearing has nothing completely stopping it from coming out :/ because of the gap between the brake cone And the bearing
I took off the cover to my drive chain on my YD 100 but when I put it back on the clutch lever is stuck and is very stiff, I tried rebuilding it but it is still stuck
Hey Hughes I have an issue with my cheap 80cc China doll and when I give it throttle it bogs down badly and then stalls if I don’t pedal to help it. I’ve tried connecting the wires and swapping them around, new cdi and magneto and replaced the piston and rings but everything wasn’t making a difference. If it was making a difference it wasn’t much of a difference. Can you please help me.
My issue is my back wheel wouldn’t spin unless you hold the clutch in like it should. But now I can push my bike and both wheels will spin without holding the clutch in. The clutch is still working a little bit but not enough to start or anything. What should I do? Love your videos by the way
It helps to use a magnet on the Bucking Bar to pull the Ball Bearing out.I use Molybdenum grease on them,and without a magnet,the bearing doesn't come out.
i dont have coaster breaks someone who installed my motor didnt do my rear sprocket very well and ive been replaceing the hardware with that i got not the wheel sometimes has a hard time turning with clutch down like it caught up
I took out the spark plug to test for spark, and when i let go of the clutch, the back tire siezed up. I suspect theres theres something wrong with the drive sproket because its the last thing i messed with when i installed the chain. i dont know whats wrong with it
Late to the party here, but mine is slightly turning with a bit of oomph and the clutch feels too free, any advice or ideas? I’m not exactly the most experienced with these so I may not fully understand what means what haha
Like in the video the clutch will not let the back wheel turn ,took clutch cover off retighten the clutch cable and it still won't start and only on one bike the wheel turns now
I need some new shirts. Problem is I lost about 90lbs then started gaining it back. Now I'm losing it again. Thanks. You helped me set a goal with rewards. When I lose enough weight to fit in Large tshirts, I'll stock up. 40lbs should get me there
I want to share my tips for reinstalling the brake arm. Firstly, on the OTHER side (bicycle drive side), I put two lug nuts on the axle and tighten them INTO each other. That is, get two wrenches, turn the top nut clockwise and the bottom nut counterclockwise. This way you can use vice grips to effectively grip the axle, put the wheel on your lap with the vice grips on the bottom, vice grips sandwiched between your thighs to keep the axle from rotating as you work with the brake arm cone nut or brake arm locking nut. I have a cheater pipe that fits perfectly into the brake arm, that sure is handy dandy. Before tightening the lock nut over the brake arm, I found out that I need to have the brake arm's cone nut juuuust a little looser than I would think, and maybe juuuuust a little looser than that even, because that locking nut pushes the cone nut in and effectively over tightens it. ALWAYS check that it's not too tight BEFORE putting the wheel back on!!! Thanks for all your great videos!
My issue is the wheel will turn when im pedaling but when I have the clutch held in it won't turn freely and I just put a new chain on it but with the old chain it would turn freely
I need some help! On my 66cc bike when I pedal I hear this screechy noise and when I start the motor or just roll the bike without the motor on the pedals spin by it self. If I let them spin when the bike is on and stop them with my feet the motor turns up and the rear wheel locks up. How do I fix this? This has never happened before?
I've got one for ya...I'll pull my clutch, and it will engage by it self. Last time, I was stopped, it engaged and knocked my back tire off alignment!! Any thoughts?!
What about the spark plug boot I think that the reason I’m not getting a spark!! No matter what I do the spark plug will not snap in place. What can I do to fix this without damaging the boot or going to buy another boot and plug…??
You can get another boot from an auto parts store. You clip the wire off right at the boot. Then you strip 1/3" of the wire off and fold it back then the terminal crimps over that. Here's one from amazon amzn.to/4bBC5zc
Thanks for your work man. I have problem with my bike. Clutch working perfectly but when I engage cluch piston become stuck instead of cycling up and down. When I remove spark plug piston again can cycle but of course engine canot run =/ I have my motorised bike in use last 4 years without big problem before that, so all parts is orginal.
Mine has several back sprockets of the bicycle and every video that I've looked up there's only one sprocket on both sides I can't figure out how to get the chain on mine bicycle side
25 year moterized bike rider here . Coaster brakes are junk, bicycle hubs and axles and bearings are junk , disc brakes are junk. custom hubs sealed bearings mc type axle and v braks are they way to go 500 rides no maintenance
I installed a spring loaded chain tensioner on my bike and it has jammed like that twice. Do you think getting a tighter spring will fix that problem if I choose to keep using this spring tensioner. Would you recommend installing a chain tensioner that isn't spring loaded?
How do I get my piston to move Abit it's a brand new engine with no mf oil in it and that blows my mind and pissed me off when I saw there was no oil cause I'm not starting it without lubrication to the engine first
You can put a socket on the output sprocket nut and turn engine over. Once you get gas into it, it will be lubricated. Don't overthink it. These are crude little engines. 40:1 gas oil mix is fine. 6,000 rpm w/ no oil and you'll have issues but that first startup won't hurt it.
![[FULL EP.13] เซียนหรั่ง พา ไททศมิตร ลงเรือฝึกสกิลหว่านแห | เฮ็ดอย่างเซียนหรั่ง | One Playground](http://i.ytimg.com/vi/EWFuf2Av0K0/mqdefault.jpg)
Hey man I literally would have gave up on my bike a long time ago if it weren’t for you, every problem I have I know you’ll have a video on it! Thankyou
Glad I could help
FR!!!!!
Same here
As soon as people start thinking about this problem this video comes out, you stay on top of things my friend. God bless.
Thanks, you too!
You definitely know what you are talking about. This is my go-to channel when I'm doing work on my bike
Great to hear!
Love your down to earth explaining how to do things and what to look for.that even us dummies can understand.keep up the good work!!
Thank you.i gave up on my bike and I just found your video today after watching over 30 vids.thank you for explaining every detail.
Perfect advice and useful. Thanks!
Thanks for making this video. I had the problem where the chain was jammed in side the motor. I was able to get the chain unjammed with just my fingers. If it wasn't for you I'd probably have to bring my bike to the repair shop!
Great video and great tips!:)-John in Texas
Thanks for your excellent helpful help and your willingness to help others my chain was too loose kept jamming at the sprocket fixed now
I like that 2x4 trick and hammer, Never thought of that really cool and simple thanks for that tidbit. I'm sure in the future I will need it, Nice video.
so helpful man, so much thanks for this video. my clutch wasnt releasing, this video answered all my questions
Glad it helped!
Thank you so much for taking the time to make this video I’m trying to figure this out and there’s plenty of information you gave on this video that I will use
Glad it was helpful!
THIS HELPED SOOOOOO MUCH!!!!!!!!
Thank you for this video I figured out why it was not working my ball bearing fell out
Great video I learned a lot 👍
Glad to hear it!
Hello Hughes, my 50cc engine won’t start because it seems to have too much compression on the block. When I put the spark plug back on its place the engine becomes too heavy and not able to pedal the bike. When I take the spark plug out the engine runs nice and smooth by turning the back wheel around. What can I do?
Thank you you got me up and running
BTW I've got another problem my gas when I turn the gas it keeps slipping g not sure how to fix it I out glue on gripper piece and plastic that turns I drilled hole for little pin to catch but it's still slipping
Thanks my guy I found the issue.
Thank you!
hey thank for this video but one question, will the rear tire not move just becuase u don’t have a ball bearing in it?
Question, I was riding my bike fine for like 6 miles to the beach, then I slowed down, turned the bike off to go up a bridge, went to start it again and when I let the clutch out and the wheel locked up. I had to back up to free the wheel, then it had trouble starting again, then after a couple times of it starting it wouldn’t start again, and the chain keeps getting looser and looser and I have no idea why because the chain is still on the sprockets and everything. Now my main problem is getting it running, I have fuel, 30:1 ration, spark, compression, and the clutch is activating fine and disengaging fine, and the wheel still sometime locks up when I peddling. I have checked everything I know to check, I am extremely stumped and have had 3 guys come over to help to look at it. No idea. Any advice?
Hey Boss the sprocket fits so well without the dust cap Sir can I just use the sProket as a dust cap or is there or will there be some unforeseen problems?? Thansk
two thumbs up great video
Thanks 👍
Hey man thankyou for the video please try answering this question, is the problem tht I haven’t put oil and gas in it like if I just try to pedal without it in will tht stop it because no lubrication or is tht not a problem
yes. you want some oil in there. just pedaling and not running isn't so good for it
My back tire barely moves when the clutch is engaged. It's pretty much stuck. It does move freely when I disengage the clutch. What do you think is my problem? Thanks.
What if I still can't get it to engage wouldnit be something wrong internally with my clutch the tire seems to move fine and the chains spin bit the clutch still seems to be locked up?
same. did you fix it?
Ayy Hughes, I have a problem with my rear hub. I already set everything up, put the sprocket on and serviced the hub...but I had the 2 loose brake pads fall out and I couldn't figure out how to get them back in. I figured I didn't need them, put on the sprocket and called it good. I didn't know I needed to put the brake arm back on. Are those pads necessary?
Edit:
I actually went ahead and did everything you showed in the video. Now my only issue is the gap between the dust cover and the bearing... My bearing has nothing completely stopping it from coming out :/ because of the gap between the brake cone
And the bearing
1000000000% necessary
I took off the cover to my drive chain on my YD 100 but when I put it back on the clutch lever is stuck and is very stiff, I tried rebuilding it but it is still stuck
Hey watcha think if i said i replaced the bearing between piston connecting rod and crankshaft?
I've never done that. I'm more into building and keeping one running
Hey Hughes I have an issue with my cheap 80cc China doll and when I give it throttle it bogs down badly and then stalls if I don’t pedal to help it. I’ve tried connecting the wires and swapping them around, new cdi and magneto and replaced the piston and rings but everything wasn’t making a difference. If it was making a difference it wasn’t much of a difference. Can you please help me.
sounds like a carb issue. What elevation are you?
@@HughesMotorized I’m at 35m above sealevel. Thanks I’ll try that at tell you how I get on.
My bike rides good when I pedal and push the clutch lever but when I let go my rear wheel locks up do you know wrongs wrong with it
My issue is my back wheel wouldn’t spin unless you hold the clutch in like it should. But now I can push my bike and both wheels will spin without holding the clutch in. The clutch is still working a little bit but not enough to start or anything. What should I do? Love your videos by the way
did you get it figured out?
It helps to use a magnet on the Bucking Bar to pull the Ball Bearing out.I use Molybdenum grease on them,and without a magnet,the bearing doesn't come out.
i dont have coaster breaks someone who installed my motor didnt do my rear sprocket very well and ive been replaceing the hardware with that i got not the wheel sometimes has a hard time turning with clutch down like it caught up
If it is the clutch sticking from been in shipping to long does it actually stick solid or is their a lil give cause mine is stuck solid
Solid
Hi again I was wondering if you live in Nova Scotia Canada
Sunnyvale Trailer Park ! No. That was a lie. I'm a bit farther south in Texas / USA
I took out the spark plug to test for spark, and when i let go of the clutch, the back tire siezed up. I suspect theres theres something wrong with the drive sproket because its the last thing i messed with when i installed the chain. i dont know whats wrong with it
Late to the party here, but mine is slightly turning with a bit of oomph and the clutch feels too free, any advice or ideas? I’m not exactly the most experienced with these so I may not fully understand what means what haha
i hope this works im going to try this tomorrow
Like in the video the clutch will not let the back wheel turn ,took clutch cover off retighten the clutch cable and it still won't start and only on one bike the wheel turns now
Watch my installation videos. Also need to see if getting spark and see if you have an intake leak
You helped me figure it out. (jammed chain)
glad I could help
Whats up man can you do a video on jackshaft/shift kits please thanks!
No
no hard feelings but they are total trash lose 1 hp to gain 0.5hp nah im fine
I'm not a fan. They rob power and run on a small chain and require a lot of maintenance & tuning
@@HughesMotorized Ok thanks just wondering
My rear wheel has locked up while running can you help me out with an idea why
Same
I dont know if I like your videos or your shirts better.
I need some new shirts. Problem is I lost about 90lbs then started gaining it back. Now I'm losing it again. Thanks. You helped me set a goal with rewards. When I lose enough weight to fit in Large tshirts, I'll stock up. 40lbs should get me there
I want to share my tips for reinstalling the brake arm. Firstly, on the OTHER side (bicycle drive side), I put two lug nuts on the axle and tighten them INTO each other. That is, get two wrenches, turn the top nut clockwise and the bottom nut counterclockwise. This way you can use vice grips to effectively grip the axle, put the wheel on your lap with the vice grips on the bottom, vice grips sandwiched between your thighs to keep the axle from rotating as you work with the brake arm cone nut or brake arm locking nut. I have a cheater pipe that fits perfectly into the brake arm, that sure is handy dandy. Before tightening the lock nut over the brake arm, I found out that I need to have the brake arm's cone nut juuuust a little looser than I would think, and maybe juuuuust a little looser than that even, because that locking nut pushes the cone nut in and effectively over tightens it. ALWAYS check that it's not too tight BEFORE putting the wheel back on!!!
Thanks for all your great videos!
great points thanks
I just bought 1 from market place and wish I could find someone to get it running
Do i need the small spring on the clutch arm.or is it the bigger spring
The small spring goes on the clutch arm, the big spring goes on the other side. The big spring just works to shield the cable.
@@mattmatter5643 ok thanks
Hey 👋, do you k ow what to do if youve lost your bucking bar?
th-cam.com/video/t4v3S0Cg2jQ/w-d-xo.html
@@HughesMotorized thanks man, i just found my bucking bar a few minutes ago. So no need. But thanks for helping out.
My issue is the wheel will turn when im pedaling but when I have the clutch held in it won't turn freely and I just put a new chain on it but with the old chain it would turn freely
I need some help! On my 66cc bike when I pedal I hear this screechy noise and when I start the motor or just roll the bike without the motor on the pedals spin by it self. If I let them spin when the bike is on and stop them with my feet the motor turns up and the rear wheel locks up. How do I fix this? This has never happened before?
Did you try everything on the video?
My rear wheel is turning but it’s spinning the wheel like the throttle is engaged slightly how do I stop that spin
Love the flat earth shirt and I’m having the same issue
I took out the bucking bar and ball. When I put the new ones in, the bar was over 1/2" sticking out. Its been 3 days of this im stumped.
I've got one for ya...I'll pull my clutch, and it will engage by it self. Last time, I was stopped, it engaged and knocked my back tire off alignment!! Any thoughts?!
Drive cover where chain is misaligned? or adjustment
What about the spark plug boot I think that the reason I’m not getting a spark!! No matter what I do the spark plug will not snap in place. What can I do to fix this without damaging the boot or going to buy another boot and plug…??
You can get another boot from an auto parts store. You clip the wire off right at the boot. Then you strip 1/3" of the wire off and fold it back then the terminal crimps over that. Here's one from amazon amzn.to/4bBC5zc
Thanks for your work man. I have problem with my bike. Clutch working perfectly but when I engage cluch piston become stuck instead of cycling up and down. When I remove spark plug piston again can cycle but of course engine canot run =/ I have my motorised bike in use last 4 years without big problem before that, so all parts is orginal.
might need a second base gasket to raise the head. If you are using a different spark plug might want to try another
@@HughesMotorized Thanks for your answer. All parts is the same including spark plug and working perfectly before this probllem start to happpen.
that's what i was getting to, [the inner part of the coaster brake]
I just bought a new 80cc kit and inside not turning should turn freely straight out of the box
I like me some "tearin' ass through the neighborhood"
and muddin' too. right??
Mine has several back sprockets of the bicycle and every video that I've looked up there's only one sprocket on both sides I can't figure out how to get the chain on mine bicycle side
Hello there I bought 3 80cc Gas Engines kits for bikes and none of them work right and there bran new
25 year moterized bike rider here . Coaster brakes are junk, bicycle hubs and axles and bearings are junk , disc brakes are junk. custom hubs sealed bearings mc type axle and v braks are they way to go 500 rides no maintenance
im peddling. as i release the clutch, the back tire stops spinning. I don't know what to do
How do take out the inner drive
a thick washer under the brake arm may also fix that problem
I installed a spring loaded chain tensioner on my bike and it has jammed like that twice.
Do you think getting a tighter spring will fix that problem if I choose to keep using this spring tensioner.
Would you recommend installing a chain tensioner that isn't spring loaded?
I like the arch tensioner. easy to adjust. hughesmotorized.com/arch-style-chain-tensioner-for-motorized-bicycle-w-skateboard-wheel-made-in-usa/
No tensioner is the best way. Keep it simple, much smoother and more quite, better performance. NO TENSIONER!¡!
How can you tell what size engine is
Put simply, bore multiplied by stroke gives you the capacity of the engine. Most of the so-called 80cc ones are 66cc
I just put in a high performance piston and cylinder now my piston is hitting the head.... How do I fix?
Post close up pics to my Facebook group: facebook.com/groups/hughesmotorized
i see there's a coaster brake on that wheel, if the bike has a coaster brake that could be the problem
My buckling bar is stuck inside without the ball bearing any idea how to get it out thanks man
brake cleaner sprayed into shaft and a small magnet might do it
@@HughesMotorized thanks I’ll try that
@@HughesMotorized no it’s totally stuck in there any other tips
First like comment and view
What to do if my clutch sprocket is stuck
How do I get my piston to move Abit it's a brand new engine with no mf oil in it and that blows my mind and pissed me off when I saw there was no oil cause I'm not starting it without lubrication to the engine first
You can put a socket on the output sprocket nut and turn engine over. Once you get gas into it, it will be lubricated. Don't overthink it. These are crude little engines. 40:1 gas oil mix is fine. 6,000 rpm w/ no oil and you'll have issues but that first startup won't hurt it.
Your funny as hell I
My clutch won't pop up on my bicycle motor
It's funny because it was the bearing and bucking bar that fell out.
Heh, took the clutch plate completely off, still acting like the clutch is engaged...I'm so confused.
That shirt, lol
My wheel won’t turn when the spark plug in, why is that. Anyone know why?
Piston hitting the plug?
Need help
join and post pics/video facebook.com/groups/hughesmotorized
u have a snail on ur hub :D
It's off now. Crawling on my shop floor
@@HughesMotorized its alive nice
after watching the video i see the washer won't fix it