Great diy! Made 2 sets of these, one for my kayak and one for my son's kayak. Made 3 simple changes on mine though. First, I made my pipe piece a little longer so the ball only has maybe 1/4" of movement so it closes/seals quicker. Second, before inserting the pipe piece, I put it on my router table and chamfered the end slightly with a 30° chamfer bit. Seems to seal better when closed. Third, after inserting the chamfered pipe chamfer side down (towards the ball) into the coupling, I then put it back onto the router table and chamfered the top with a 45° chamfer bit deep enough that there's barely an edge around the top. Helps direct water down into the valve instead of getting stuck on the flat ring at the top. Hope you'll try a set with the upgrades. Great and simple diy. Thanks for the base idea. Works great.
I really like your innovative idea for the bottom of the plug. Other DIY's use a screen which eventually clogs. The String Trimmer line is ideal. Thanks for sharing!!
Nice! Took my Lure 11.5 out on the lake today with a new trolling motor setup and water ended up in the back so these might be just what the doctor ordered. Thanks!
@@unclebilloutdoors136 I did build a set for my back cargo area on my Lure 11.5. Oddly though the couplers I purchased didn't even come close to fitting the scupper holes on the kayak and I needed a lot of electrical tape to make them fit snugly. That being said, they seem to work well. Oh, and I had those Nerf balls around the house from a Nerf pistol my son and I use so it worked out great.
That's wierd that the scupper holes are different sizes, but I have a couple in the middle of the kayak that are bigger. I used the stock feelfree plugs in those. I experimented with cutting a groove in the coupler with my table saw and adding an o ring. Turned out I didn' t need to use it that way, but might work well for larger holes.
Very nice. You were recommended by the MI Woodsman. So I came over and checked it out watch to complete your videos. So I subscribe to your Channel. May your days be long and a life full of joy. Keep Your Head on a swivel. Stay safe stay healthy. Tell next time. Gunny James
They seem to work well for me. One tip, Bevel the inside edge of the inner peice of pvc where the ball comes up and meets it. I found this helps keep the ball from sticking in the up position.
Excellent idea. I made the screen version but it plugged up the first rain that washed some debris in it. The ball I used was too big, barely enough room the move...I'll use your nerf gun ball! Just have to add the trimmer string and get a nerf ammo ball Thanks for sharing!
I got caught on Lake Erie in some pretty hefty waves. (4-5 feet). I got swamped a couple of times and both times the water drained right out. It seems the pressure of the water trying to drain out is enough to push the balls down.
Why not skip the weed eater line and duplicate the holding ring you made? And just hold the rings in place with a touch of glue? Would that work or am I missing something? This will be my first time combining kayaking with fishing. Just askin'.
Although I have not tried doing what you suggest, I believe duplicating the ring on the bottom would restrict the flow of water out of the plug, much as the ball seating on the ring stops water from coming up through the svupper. I saw a video that used a piece of window screen on the bottom, but that seemed it would trap sand and debris and need to be cleaned out.
@@unclebilloutdoors136 I agree, it will prevent flow in both directions. Maybe one could dremel-grind the leading edge of a bottom ring that would create a gap for downward flow. This is all, of course, if you don't have access to trimmer line. (Mine isn't cylindrical in profile).
very clever. My kayak (Native Watercraft Slayer Propel 10 MAX) scupper plug holes are bigger, 2 inch in diameter. I wonder if there are proper size PVC pipes for this DIY....
I tried pvc on both ends. I also tried a piece of window screen. I found that if coarse sand or other small debris got into the scupper from the top, it would clog up and not allow the plug to work properly and I had to remove the plugs to clean them quite often. The trimmer string allows any debris to pass through easily.
Great diy! Made 2 sets of these, one for my kayak and one for my son's kayak. Made 3 simple changes on mine though. First, I made my pipe piece a little longer so the ball only has maybe 1/4" of movement so it closes/seals quicker. Second, before inserting the pipe piece, I put it on my router table and chamfered the end slightly with a 30° chamfer bit. Seems to seal better when closed. Third, after inserting the chamfered pipe chamfer side down (towards the ball) into the coupling, I then put it back onto the router table and chamfered the top with a 45° chamfer bit deep enough that there's barely an edge around the top. Helps direct water down into the valve instead of getting stuck on the flat ring at the top. Hope you'll try a set with the upgrades. Great and simple diy. Thanks for the base idea. Works great.
Great ideas. I did modify mine with the chamfer on the ends of the pipe piece. Helps alot.
And this is why when your elders speak, you remain silent, & listen!!! Appreciate the knowledge Uncle Bill !!! 👍
I really like your innovative idea for the bottom of the plug. Other DIY's use a screen which eventually clogs. The String Trimmer line is ideal. Thanks for sharing!!
Genius! What a great solution. Much cheaper than any one way valve you can buy. I'll be sizing my scupper holes. Thanks!
Nice! Took my Lure 11.5 out on the lake today with a new trolling motor setup and water ended up in the back so these might be just what the doctor ordered. Thanks!
They definitely help keeping the hull dryer.
@@unclebilloutdoors136 I did build a set for my back cargo area on my Lure 11.5. Oddly though the couplers I purchased didn't even come close to fitting the scupper holes on the kayak and I needed a lot of electrical tape to make them fit snugly. That being said, they seem to work well. Oh, and I had those Nerf balls around the house from a Nerf pistol my son and I use so it worked out great.
That's wierd that the scupper holes are different sizes, but I have a couple in the middle of the kayak that are bigger. I used the stock feelfree plugs in those. I experimented with cutting a groove in the coupler with my table saw and adding an o ring. Turned out I didn' t need to use it that way, but might work well for larger holes.
Very nice. You were recommended by the MI Woodsman. So I came over and checked it out watch to complete your videos. So I subscribe to your Channel. May your days be long and a life full of joy. Keep Your Head on a swivel. Stay safe stay healthy. Tell next time.
Gunny James
Thanks Gunny. All the best to you.
Great DIY Bill , might have to try this one on my Kayak as well !
thanks for sharing
atb john
PS. got the stickers thanks!
Briliiant idea 'Uncle Bill'
Not only cheaper than normal scupper plugs but better too .. they do the same job as a self bailer on a sailing dinghy.
They seem to work well for me. One tip, Bevel the inside edge of the inner peice of pvc where the ball comes up and meets it. I found this helps keep the ball from sticking in the up position.
Excellent idea.
I made the screen version but it plugged up the first rain that washed some debris in it.
The ball I used was too big, barely enough room the move...I'll use your nerf gun ball!
Just have to add the trimmer string and get a nerf ammo ball
Thanks for sharing!
Brilliant!
Very creative! Im thinking about using my kayak in the surf. Would the water accumulate and fill up the kayak until the ball drops?
I got caught on Lake Erie in some pretty hefty waves. (4-5 feet). I got swamped a couple of times and both times the water drained right out. It seems the pressure of the water trying to drain out is enough to push the balls down.
@@unclebilloutdoors136 Sweet! Can’t wait to rig up my yak. Thank you!
@@JosePerez-zm8ln Hope they work out well for you.
Love this! Thanks for sharing.
You bet Mark.
Thanks for the video
You bet!
Great idea thanks for sharing
Thank you for Sharing, this is a great idea, and works so well
Thanks Bob. Works great for me.
I have a Lure 13.5 on the way, so this Applies directly to Me and my needs
Great. I think you will love your new Lure.
Just excellent thank you so very much
Why not skip the weed eater line and duplicate the holding ring you made? And just hold the rings in place with a touch of glue? Would that work or am I missing something? This will be my first time combining kayaking with fishing. Just askin'.
Although I have not tried doing what you suggest, I believe duplicating the ring on the bottom would restrict the flow of water out of the plug, much as the ball seating on the ring stops water from coming up through the svupper. I saw a video that used a piece of window screen on the bottom, but that seemed it would trap sand and debris and need to be cleaned out.
@@unclebilloutdoors136 I agree, it will prevent flow in both directions. Maybe one could dremel-grind the leading edge of a bottom ring that would create a gap for downward flow. This is all, of course, if you don't have access to trimmer line. (Mine isn't cylindrical in profile).
Thank you
very clever. My kayak (Native Watercraft Slayer Propel 10 MAX) scupper plug holes are bigger, 2 inch in diameter. I wonder if there are proper size PVC pipes for this DIY....
Could be. I am not sure the diameter of a 1" or 1 1/2" coupling. The o.d. of 1 1/2" schedule 40 pvc might be close.
They make a pvc coupling called a no hub slip coupling.
Great idea!!!
Ingenuity 👌🏼
Why do you use the trimmer string? Why not just the PVC pipe on both sides?
I tried pvc on both ends. I also tried a piece of window screen. I found that if coarse sand or other small debris got into the scupper from the top, it would clog up and not allow the plug to work properly and I had to remove the plugs to clean them quite often. The trimmer string allows any debris to pass through easily.
Great idea thanks for sharing!! New subscribe!
Thank you sir. You have a new sub as well.
Pacing