I've found something interesting. There's two versions of the GoolRC 60 amp ESC. This version you have here and another with a push button on off switch and a different fan and fan cover. The version you have seems to have much better acceleration while the other version has a lesser amount of power output off the line. Just something I've observed. Both ESC have been programmed the same way with the program card.
Just saying I hear that they’ve got some medium power system so if you full throttle at the start your car won’t flip over, says u can program somewhere in the programming card
Hi, very nice video! I have the goolrc esc 60A, and when I start it (having the throttle full max) it starts beeping constantly (red light blinking too). Then moving it to neutral, I hear 3 beeps, and the constant beeping stops. After that, only forward works, reverse does not. I use a Flysky FS-i6X transmitter. Any ideas?
Sorry don’t know. But make sure you try reverse twice as the 1st time it just stops the ecu then the next occasion actually makes it go backwards. So you need to go reverse > neutral > reverse to actually go backwards.
@@subarubrett you have to move the throttle to neutral (middle) for 1 sec first, then moving backwards works. In general, to change direction, you stop the throttle to zero first.
I can’t get mine to work. It just makes some kind of musical bleeping sound for a few seconds and then I can barely get the wheels to spin - any thoughts? I’m running an nimh batt but that shouldn’t matter? Esc is identical to yours
Nimh might be knackered if it’s old. I would try different batt if poss. However it’s also poss motor is fubared. Ideally you should swap it with a known good one. Other than that nothing you can do really except check connectors thoroughly
@@RobertNES816 why need to shut off voltage cut off? Just for calibration? Thank you for your tip, I have same issue, wil ltry ASAP :) edit: still not working.
it may be ‘cogging’ if you look that up. basically cheaper sensorless motors aren’t smooth at low rpm. they are better once they get going. so probably not ideal for crawling in particular, as you intentionally want to go slow. Unfortunately you may need a more pricey sensored ecu and motor set up.
I don't know the language. The sixth sense followed you and I succeeded in applying the operation. Thank you very much. More
Great job. I went thru 20 how to videos and no of them was as easy as yours. Great job and I did get mine on the right track. Thanks again.
Thanks for presantation.
I think this worked for my dumbo and 35amp goolrc in a hs181. Thanks
I've found something interesting. There's two versions of the GoolRC 60 amp ESC. This version you have here and another with a push button on off switch and a different fan and fan cover. The version you have seems to have much better acceleration while the other version has a lesser amount of power output off the line. Just something I've observed. Both ESC have been programmed the same way with the program card.
Just saying I hear that they’ve got some medium power system so if you full throttle at the start your car won’t flip over, says u can program somewhere in the programming card
My goolrc is beeping and it was flashing red now it’s not flashing red on my Receiver what do I do how do I fix it
thanks for info as I have lost my user guide for the esc/ motor combo
That’s great. I’m not an expert but filmed what I could as best I understood it.
Hi, very nice video! I have the goolrc esc 60A, and when I start it (having the throttle full max) it starts beeping constantly (red light blinking too). Then moving it to neutral, I hear 3 beeps, and the constant beeping stops. After that, only forward works, reverse does not. I use a Flysky FS-i6X transmitter. Any ideas?
Sorry don’t know. But make sure you try reverse twice as the 1st time it just stops the ecu then the next occasion actually makes it go backwards. So you need to go reverse > neutral > reverse to actually go backwards.
@@1_RC you are right! everything works (and used to work). It is the 2nd time that goes backwards! thanks a lot for your prompt reply!
Did you ever figure this out? I’m having the same issue with mine.
@@subarubrett you have to move the throttle to neutral (middle) for 1 sec first, then moving backwards works. In general, to change direction, you stop the throttle to zero first.
I have the problem where it’s faster in reverse. Gonna try this, thanks!
You have to reverse your throttle on the transmitter.
Mines having the same problem and I’ve tried everything reversing throttle and everything but it just still goes faster in reverse
@@ggg_2414 brushless motor? swap over the outer wires to change the motor spin.
Change the sec wire and servo 1 is to gas 2 it to steer
I can’t get mine to work. It just makes some kind of musical bleeping sound for a few seconds and then I can barely get the wheels to spin - any thoughts? I’m running an nimh batt but that shouldn’t matter? Esc is identical to yours
Nimh might be knackered if it’s old. I would try different batt if poss. However it’s also poss motor is fubared. Ideally you should swap it with a known good one. Other than that nothing you can do really except check connectors thoroughly
You need to program the ESC to shut off low voltage cut off. You have to buy the program card for it.
@@RobertNES816 why need to shut off voltage cut off? Just for calibration? Thank you for your tip, I have same issue, wil ltry ASAP :)
edit: still not working.
Any ideas on crawling with this i bought 3800kv combo with 60 amp esc however trying to crawl it seems to bounce
it may be ‘cogging’ if you look that up. basically cheaper sensorless motors aren’t smooth at low rpm. they are better once they get going. so probably not ideal for crawling in particular, as you intentionally want to go slow. Unfortunately you may need a more pricey sensored ecu and motor set up.
@@1_RC thank you so much ok I aill.try changing esc settings and see if it helps but that makes sense
This didn’t work for me also haven’t tried the program card yet but I reversed to polarity and works as it should
Interesting? Mine won’t works but not programmed yet. I’ll try that
Has it worked?
Andrew Deuling no, it will program your throttle points. But not settings. It does have 100% forward, 30-40% in reverse.