Please ditch the music. There were times when his voice volume dropped and then muddled with the low music. It really isn't necessary to have music. Other than that, I thank you for the information that you provided
You don't have to ditch the music entirely, just put a compressor on his vocal track to equalize the volume of his voice so it always clearly heard above the music
Absolutely ditch all the music, if your content has value, as yours does, you don't need any bullshit noise to distract from your instruction, and the sounds of the work itself.
That video actually is the first one of its type that I have seen and that actually explains the problem of clunking or diff noise and gives a detailed explanation of the solution... I hope these things would apply also to the old audi a4 quattro rear differentials. Many thanks
Doesn't tell you how to adjust the backlash or does the new part fixed the backlash? How does the backlash get messed up in the first place ?Helppppp... great video though you really explain yourself well sir.
Hi - I think this is a great video and I easily understood what needs to be done to diagnose this issue. What would you say a friend should be charging you to do this work for you as a side job? 2013 Jeep Wrangler or a friend of a relative? Even is they are a high end mechanic
Put new set of gears in my GM 10 bolt notice during the break in it makes a slightly sound when slightly on the gas , Did the backlash to specs any idea ,And BTW what brand gears did you use ?
Dial indicator - There’s a way better dial indicator than the one you were using to check the backlash. You get a lot of cosine error using the method you were using. Like .008 actual measurement shows up like .012 on the dial. Basically it is easy to have things too tight. You should be set up parallel to centreline, square to the tooth centreline for accurate measurement. Pattern - If your pattern is good on the drive side your backlash will be right and the coast side will be exactly where it is machined to be. You can move the contact point around but you can’t change the drive-coast relationship. It’s how they are ground.
If i have a low humming sound when you give it gas and goes away when you coast is this a big problem or should I just drive it or need to be fixed it has 240000 on her. Thanks Sir.
I have an 02 ram 1500 with 3.92 gears... just completely replaced the rear end as the old one got ran dry and i drove the truck till it imploded.. it seized and ended up taking out my driveshaft, gas tank, overdrive housing on my 46re trans, exhaust, etc. Bought all the parts and rebuilt the truck myself for about 1300$ but would have easily cost 5000$ in parts/labour at a shop. Long story short if you hear alot of noise coming from your rear end stop driving you'll save alot of money in the long run lol
I got a 4x4, does it on deceleration, but sounds like in front. Would this be same issues but just in the front differential? How would you check front one, sme way as the things you're doing for this rear diff? Im just trying to figure out few things before i start repairing whatever is making my noise on deceleration. Thanks!
Hello guys I just had a over a year old 2019 small compact suv. And it’s been. Rear ended last year. I bought it new last January and I been rear ended. March 2019. They fixed it and now the noise come. At the rear Thank you
+Christian Basa Thanks for checking us out! We would suggest taking the vehicle back to where it was originally fixed. Please let us know if you have any further questions, thank you!
I have a humming sound on my rear driver side. I thought it was the wheel bearing, replaced it, but that wasn't the problem. What you are describing might be the issue. Another issue is finding a mechanic that knows his stuff.
+@michaelsmithdjsmitty4538 We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
If the noise is only there only when accelerating, would you say its the pinion and ring position? Or also possibly the bearings? Or would the bearing be constant?
I'm having my rear differential repaired tomorrow. I drive a 2017 Infiniti QX30. It had 10,800 miles on it when I bought it in July of 2020 and now has only 25,500 miles. Despite the low mileage, I started getting a whine about a month ago, had it looked at last week, and was told the rear differential is "shot". I didn't buy that for a second, so I'm bringing to AAMCO Transmission, who thinks it will probably need minor repairs considering the mild symptoms and low mileage. I guess I'm the culprit for never having changed the differential fluid, but I had no idea it was a maintenance item. I'm 65 years old, have been driving various makes and models of cars for 50 years, and never changed the differential fluid and never had a problem. I wonder how much time it took for this guy to fix this one.
I have a 2007 Chevy Avalanche, and the noise I hear coming from the rear of the truck sounded like the Sway Bar Links were dry, so I went and purchased a hand held Grease Gun from Harbor Freight and added grease, but that did not eliminate the noise. I then raised the rear of the vehicle and shook the tire, and discovered there was "in and out" movement of more than 10 thousands of a inch. Is this a Bearing problem, or something more??
His description of when this pickup makes it's "Noises" & how it sounds as well is nearly match to what I've got with my 2002 Toyota Tundra. Unfortunately, Tundra's have no removeable rear cover to check anything. Since the rear differential & axels are all within a housings & can only be serviced by unbolting the axel coverings (I think, it's been awhile since I really looked at all of it) it's a monumental undertaking to do any work on any part of what's back there. I believe the mechanic I had "Look & Listen" to it came to the conclusion that it's axel bearing was the problem, but learned it was "PROPIETARY" to my pickup from some information (rather obscure information) he found somewhere. If anyone could direct me to an "OBSCURE SOURCE OF INFORMATION" regarding an odd size of the rollers/balls used in the rear end axel bearing/s in a 2002 Toyota Tundra, it would be greatly appreciated.
Excellent information but PLEASE learn to control the audio levels when editing your videos. The voice level was so low I had to crank my volume just to hear him speaking and then at 5:53 your logo transition comes in and was loud enough to wake the neighbors! How did this get past your editor? Wow! I'm not hatin - I swear. I loved the video. Your videos are always very informative and extremely helpful. I'm just trying to help. Unless it was just me.... Anybody else lose an eardrum at 5:53?
My 02' Blazer ZR2 w/ a G80 Locker in the rearend was making a whining sound at 25mph & faster. Found out it's my Pinion Bearing going out, even though everything is tight & no leaking. No clunking, etc. Just a whine. I'll turn the radio up a little louder lol
Hi I’m looking at a 2007 Yukon Denali he says there’s a brand new engine in a newer transmission that was installed. He said the rear end is jumpy and thinks the rear differential is going bad. Not exactly sure what that means?
Hello sir may I ask ,about my car when I shifting to 2nd gear in uphill I heard weird noise under at the back of my car what's the problem that I need to fix ? Please give an advice.
Hi, Question: I am traveling and near Saint Augustine, Florida, do you know who rebuilds re-ends in this area, or how to find some one honest and qualified? My front seal just blew out. Need to decide if I fix or crap the van.
You'll get a better pattern if you push the ring gear against the pinion. Easier to do than turning the pinion and produces a nice pattern since you're pushing against the pinons gear preload.
+Jeffrey Conway Thanks for watching! If you have any issues with a part you ordered from us please be sure to contact our customer service department right away! Our contact info can be found here; www.1aauto.com/about/contact
Hello I’m hearing a wine from my 2017 scatpack challenger when I step on the gas not sure what the problem could be when I let go of the gas pedal it goes away ?
+@dennisl3072 We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Saul Perez Esparza oh lucky you hopefully doesn’t come back I’m looking at a $1500 fix and could possibly be more depending on if other parts are damaged 😓
I have rear end clicking, during turns when engaged in 4x4 :/ mechanic cant figure it out, when its in 2x2 no issues when turning or driving, but when i engage 4x4 it has clicking sounds, any idea? There,were some damage to the side of the tire before, but axle is not bent and passed alignment no issues?.... any clues? Thanku in advance!
My 2009 F150 rear differential only makes noise on real light acceleration under load meaning if I have it on the list I want to hear the noise at all not sure what it could be
I'm having issues with my 2013 BMW M5. We changed out both axles but now I'm getting noise in the back when I'm accelerating and getting a drive train malfunction. Any ideas ?
I HAVE A 2012 RAM 1500 4X4 AND AS I AM DRIVING DOWN THE ROAD AND IT HOWLS OR ROARS AS I SPEED UP .if i turn to the right the noise quiets down but it doesnt when i turn left. To me it sounds like its in front end ? Would that actually still be the rear diff. The truck has 169000 miles on it .
I bought a 97 F150 in late 96. It was perfect until a recall and the dealer said they knocked the weight off the driveshaft and had to replace it. After that I had a roaring noise from the rear and took it back. They said it was the Firestone tires and I would have to take it to them. About that time I got a company car and almost never drove my truck. I just lived with the noise for years when I did. Finally had the tires replaced and the noise remained. 97,000 miles later it’s still there. Truck runs great but I can’t find anyone who can tell me what’s causing the noise.
Got my rear diff done by a local highly recommended shop with lower gears and a trutrac installed, makes a howl on decel at 40-45 brought it back says it’s no big deal and such they put some Lucas in and was quiet for a month or two and it’s back been like that for two years hasn’t gotten worse but sure is annoying
On a 4x4, if my noise does it in 4hi, would that mean it's NOT the front diff? Could i rule out the front one? Im having hard time telling if sound it's making(on deceleration only), is in the front or back. Any help is appreciated! Thx
My rear was making similar noise and an oil change solved the problem. I was on a road trip and didn't own a dial indicator thus didn't measure backlash.
I have a 09 GMC Sierra 2500 gas and I’m at 150k miles. Doing the exact same thing as this ford I can feather the throttle and it’ll make a winding howling noise. Basically only under load but once I let off it goes away. But after watching this video it’s basically everything in the rear end is done for I guess. How bad is it to keep driving it as it is?
Thank you for your video. Would you be able to guide me with this issue I'm having. I have a 05 chevy tahoe, 3.42 gears. GU6,G80. lately when I turn in either direction at a slow speeds, my rear wheels start to lock up and drag as if I was braking but I'm not. I am also starting to hear a growl when coming to slow stop. Any idea on what can be causing this issue and how to remedy. It's my daily driver and need it back on the road. I am also running 37" tires. Your input or advice will be greatly appreciated. Thank you
I have a BMW 530 I have a rear differential humming sound not like this exactly, it's smooth but annoying Is it really dangerous ?? Can I drive for a long trip ? Is it just a sound or should I fix it soon ?? It will cost me 3000$
I have a 96 k2500 and mine makes noise when you let up on it not when you're accelerating bearings? Carrier bearing? The truck was dad's and is a pampered garage Queen with 98,000 miles on it
I have a F150 2016 only 182.000km and i have that problem.. is look like a big problem with the Ford F150 a never have that problem with my Ford Ranger 4x4 XLT 2009 and i have 355.000km on its. Can you drive for long time with a hauling noise . like that's ???? 🤔🤔🤔 before readjusting the back lashes or change pinion abd ring Gear.....
+Haven Barner We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
+@RMason1971 We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Very informative video! You definitely have thorough knowledge of your craft. I was trying to find out the possible cause of much body noise in the rear of my 2002 nissan pathfinder. Can you help me with a solution to end the annoying noise?
i have a 2018 Jeep Compass 4x4 with 2 speed diff (locking 4wd). Around 35-40 MPH i hear a low hum through the vehicle (can't pinpoint front or back of car.), constant no matter how much or little i accelerate. However, If i turn the Traction control off, it goes away. Any ideas?
+Mark m We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
I'm confused about the differential. I'm looking everywhere for a maintenance schedule of differential fluid for my Honda Accord but I can't find anything. Where is the differential located in my car and should I be changing this fluid on regular intervals? Thanks!
My 2012 mustang V6 is making noise in the rear end and it’s also leaking oil. The noise it makes is like it’s grinding against something and like a roaring noise as well. How do I fix this and how much will it cost me to fix this? I was told to not drive my car until I fix it. Where should I go and what should I do? Someone please help and give me some ideas. Can I do this job myself?
Can a carrier bearing cause a shuttering, almost a crunchy vibration at slow speeds after a few mins of highway speed? It doesn't do it unless i run 60-70mph for 10+ mins. I also have a humming sound that seems like a wheel or carrier bearing. I'm having a hard time getting the prob diagnosed. It's an 07 AWD Saturn Vue.
Did you ever figure out this problem? I have something similar in a suburban, at highways speed, but it takes like 15 minutes of driving before it happens.
So basically what this is telling me is.. if I don't want to spend several hundred dollars for parts, and several hundred dollars in tools, less a whole day of work and a machinist degree in mechanics, then it is just easier to get a $250 junkyard rear end and be done with it. Sometimes you got to know when to hold them, and know when to fold them.
Exactly, I have the same situation with my 2010 Silverado that last owner put a Yukon dirá grip and rear gears. It makes the noise when feathering the gas and goes away when I let off. It’s annoying, I really considering just going to the junk yard and swapping out the entire rear axle assembly my self and call it a day. It would be a hell of a lot cheaper fix .
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto
√ *Do it Yourself*
√ *Save Money*
Please ditch the music. There were times when his voice volume dropped and then muddled with the low music. It really isn't necessary to have music. Other than that, I thank you for the information that you provided
+hasaywha Thanks for the feedback! We'll pass this info along to our production team.
You don't have to ditch the music entirely, just put a compressor on his vocal track to equalize the volume of his voice so it always clearly heard above the music
That’s what closed captioning is for
Absolutely ditch all the music, if your content has value, as yours does, you don't need any bullshit noise to distract from your instruction, and the sounds of the work itself.
In '84 I bought a Supra. The diff was noisy but the dealer said not to worry. 205,000 miles later when I sold it, the diff was still noisy.
That video actually is the first one of its type that I have seen and that actually explains the problem of clunking or diff noise and gives a detailed explanation of the solution... I hope these things would apply also to the old audi a4 quattro rear differentials. Many thanks
+ivanez1im Thanks for checking us out. Shop for high quality auto parts on 1AAuto.com:
1aau.to/m/Shop-1AAuto-c
Doesn't tell you how to adjust the backlash or does the new part fixed the backlash? How does the backlash get messed up in the first place ?Helppppp... great video though you really explain yourself well sir.
I am extremely impressed with the level of his expertise. I wish he was who I took any and all of my repairs. What a rockstar
Finally a good video by 1a auto! Two thumbs ups!! lol
My rear end makes noise after eating Mexican food. Sounds like air escaping, just changed out my diff. and now the noise is fixed. Thanks man
Don't leave the plug in there too long. It may cause excessive pressure buildup, thus causing your rear end to explode.
I laughed way too hard at this comment 🤣😂🤣😂
this was an exceptional video. very informative. thanks a lot.
My crown vic is having what appears to be a similar problem. Glad I found this video.
+Summs Thanks for checking us out. Shop here for high quality auto parts: 1aau.to/m/Shop-1AAuto
Yes Finally a video describes the noise I’m having in my jeep ..thanks
Same here!
Same here! Been HOWLING for 5 years. It's gotten significantly worse past 2 months and now other bearings are going out
Hi - I think this is a great video and I easily understood what needs to be done to diagnose this issue. What would you say a friend should be charging you to do this work for you as a side job? 2013 Jeep Wrangler or a friend of a relative? Even is they are a high end mechanic
Put new set of gears in my GM 10 bolt notice during the break in it makes a slightly sound when slightly on the gas , Did the backlash to specs any idea ,And BTW what brand gears did you use ?
Good video and your mechanic did a great job. Nice to see younger kids in the business.
+Tim Hasselbach Thanks for checking us out!
Dial indicator - There’s a way better dial indicator than the one you were using to check the backlash. You get a lot of cosine error using the method you were using. Like .008 actual measurement shows up like .012 on the dial. Basically it is easy to have things too tight. You should be set up parallel to centreline, square to the tooth centreline for accurate measurement.
Pattern - If your pattern is good on the drive side your backlash will be right and the coast side will be exactly where it is machined to be. You can move the contact point around but you can’t change the drive-coast relationship. It’s how they are ground.
+Jared Mayer Thanks for checking us out!
If i have a low humming sound when you give it gas and goes away when you coast is this a big problem or should I just drive it or need to be fixed it has 240000 on her. Thanks Sir.
Good day I have a 04 tahoe, when driving above 50 there's this whining sound from the differential do I need to overhaul it ,is your ship in queens
This just might be my issue. Would you know how much for the repair?
~GREAT Vid
I have an 02 ram 1500 with 3.92 gears... just completely replaced the rear end as the old one got ran dry and i drove the truck till it imploded.. it seized and ended up taking out my driveshaft, gas tank, overdrive housing on my 46re trans, exhaust, etc. Bought all the parts and rebuilt the truck myself for about 1300$ but would have easily cost 5000$ in parts/labour at a shop. Long story short if you hear alot of noise coming from your rear end stop driving you'll save alot of money in the long run lol
Hi mine is rumbling quite a bit, is it ok to drive for a while till I can fit it in at the garage in about a weeks time? As I need it for work
Check the oil level
Great video. What's a job like that cost? Thank you, John
I got a 4x4, does it on deceleration, but sounds like in front. Would this be same issues but just in the front differential? How would you check front one, sme way as the things you're doing for this rear diff? Im just trying to figure out few things before i start repairing whatever is making my noise on deceleration. Thanks!
Hello guys
I just had a over a year old 2019 small compact suv. And it’s been. Rear ended last year. I bought it new last January and I been rear ended. March 2019. They fixed it and now the noise come. At the rear
Thank you
+Christian Basa Thanks for checking us out!
1A Auto Parts is that would be the cause. Should I go to my dealership or to the one who fixed my car ? Thank you
+Christian Basa Thanks for checking us out! We would suggest taking the vehicle back to where it was originally fixed. Please let us know if you have any further questions, thank you!
I have a humming sound on my rear driver side. I thought it was the wheel bearing, replaced it, but that wasn't the problem. What you are describing might be the issue. Another issue is finding a mechanic that knows his stuff.
+@michaelsmithdjsmitty4538 We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Mines sounds like metal clanking when I accelerate but I can’t tell if it’s the front or back one and if it’s not a axle or not
If the noise is only there only when accelerating, would you say its the pinion and ring position? Or also possibly the bearings? Or would the bearing be constant?
I'm having my rear differential repaired tomorrow. I drive a 2017 Infiniti QX30. It had 10,800 miles on it when I bought it in July of 2020 and now has only 25,500 miles. Despite the low mileage, I started getting a whine about a month ago, had it looked at last week, and was told the rear differential is "shot". I didn't buy that for a second, so I'm bringing to AAMCO Transmission, who thinks it will probably need minor repairs considering the mild symptoms and low mileage. I guess I'm the culprit for never having changed the differential fluid, but I had no idea it was a maintenance item. I'm 65 years old, have been driving various makes and models of cars for 50 years, and never changed the differential fluid and never had a problem. I wonder how much time it took for this guy to fix this one.
So would just replacing diff fluid get rid of the clunking noise?
great. answered my questions on why I have dif noise
How long should I drive it to let the new differential additive oil get in there well?
I have a 2007 Chevy Avalanche, and the noise I hear coming from the rear of the truck sounded like the Sway Bar Links were dry, so I went and purchased a hand held Grease Gun from Harbor Freight and added grease, but that did not eliminate the noise. I then raised the rear of the vehicle and shook the tire, and discovered there was "in and out" movement of more than 10 thousands of a inch. Is this a Bearing problem, or something more??
His description of when this pickup makes it's "Noises" & how it sounds as well is nearly match to what I've got with my 2002 Toyota Tundra. Unfortunately, Tundra's have no removeable rear cover to check anything. Since the rear differential & axels are all within a housings & can only be serviced by unbolting the axel coverings (I think, it's been awhile since I really looked at all of it) it's a monumental undertaking to do any work on any part of what's back there. I believe the mechanic I had "Look & Listen" to it came to the conclusion that it's axel bearing was the problem, but learned it was "PROPIETARY" to my pickup from some information (rather obscure information) he found somewhere. If anyone could direct me to an "OBSCURE SOURCE OF INFORMATION" regarding an odd size of the rollers/balls used in the rear end axel bearing/s in a 2002 Toyota Tundra, it would be greatly appreciated.
+Sonny Burnett Thanks for the feedback!
Excellent information but PLEASE learn to control the audio levels when editing your videos. The voice level was so low I had to crank my volume just to hear him speaking and then at 5:53 your logo transition comes in and was loud enough to wake the neighbors! How did this get past your editor? Wow! I'm not hatin - I swear. I loved the video. Your videos are always very informative and extremely helpful. I'm just trying to help. Unless it was just me.... Anybody else lose an eardrum at 5:53?
VST plugin compressor limiters are free. They should final edit with one. I hate uneven audio too.
But how do you adjust the backlash? shimming of the bearings?
Shimming
My 02' Blazer ZR2 w/ a G80 Locker in the rearend was making a whining sound at 25mph & faster.
Found out it's my Pinion Bearing going out, even though everything is tight & no leaking. No clunking, etc. Just a whine. I'll turn the radio up a little louder lol
I hear a noise only when decelerating and a lot of fluid leak from the pinion side what could this be
Hi I’m looking at a 2007 Yukon Denali he says there’s a brand new engine in a newer transmission that was installed. He said the rear end is jumpy and thinks the rear differential is going bad. Not exactly sure what that means?
I need a GMC Yukon rear diff asap like now you said click the link for parts but I don’t see any contact information
Andy you need to do more of these. But I'd like to see you do more stuff in 2500s 3500s
If I have a scrape marks from the pinion gear on my differential housing will it be pinion gear or differential that’s bad?
Good job on the video very explanatory thank you.
Hello sir may I ask ,about my car when I shifting to 2nd gear in uphill I heard weird noise under at the back of my car what's the problem that I need to fix ? Please give an advice.
He is troubleshooting like a pro, just saying, it does not get done better than this.
Superb job to thumbs up for that mechanic in his great great work.
+KEITH KUHN Thank you for your positive feedback! We are happy we could help!
Hi, Question: I am traveling and near Saint Augustine, Florida, do you know who rebuilds re-ends in this area, or how to find some one honest and qualified? My front seal just blew out. Need to decide if I fix or crap the van.
Any idea much and where can I shop 2018 Nissan Pathfinder Platinum Differential... ?
You'll get a better pattern if you push the ring gear against the pinion. Easier to do than turning the pinion and produces a nice pattern since you're pushing against the pinons gear preload.
+Jeeper80 Thanks for the tip!
I bought a front drive shaft for my 2006 Yukon from you guys and the boot already blew is that covered under a warranty
+Jeffrey Conway Thanks for watching! If you have any issues with a part you ordered from us please be sure to contact our customer service department right away! Our contact info can be found here; www.1aauto.com/about/contact
Excellent video! Maybe the best I’ve seen on the topic.
How much does a rebuild job cost on average? Am trying to decide whether to fix or scrap my 91 G-20 van.
You're very good at your job
+Matt Adams Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Hello I’m hearing a wine from my 2017 scatpack challenger when I step on the gas not sure what the problem could be when I let go of the gas pedal it goes away ?
For a manual RWD car - would there still be a humming noise if coasting in neutral? Thanks in advance!
+@dennisl3072 We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
i have like this problem when i turning left or right some noise happening is that also differential? w205 RWD
Can you make a video on the bearing near the wheel? I think I have that problem on my jeep xj
Saul Perez Esparza hey any update on your Jeep? I’ve got a weird choppy humming noise rear end on my patriot
Kingg Casanovaa out of no were it stopped making the noise, I haven’t check since then
Saul Perez Esparza oh lucky you hopefully doesn’t come back I’m looking at a $1500 fix and could possibly be more depending on if other parts are damaged 😓
How much does it cost for a job on a Nissan frontier v6 XE cost? Any help would be great
I have rear end clicking, during turns when engaged in 4x4 :/ mechanic cant figure it out, when its in 2x2 no issues when turning or driving, but when i engage 4x4 it has clicking sounds, any idea? There,were some damage to the side of the tire before, but axle is not bent and passed alignment no issues?.... any clues? Thanku in advance!
My 2009 F150 rear differential only makes noise on real light acceleration under load meaning if I have it on the list I want to hear the noise at all not sure what it could be
I get some noise from my Honda crv rd1, but it's differential looks different from the one you are handling
when should you change the differential fluid
90k+
What is a rough estimate (price) on what you just worked on
$1000
That sounds about right a shop just gave me an estimate on a k2500 for $1,200, this truck has less than 100,000 miles on it and hardly ever towed
They charging me 1400 for the whole part and new filter,gasket and oil for transmission is that bad ?
Thank You! Answer my question.
SUPER VIDEO. A RARE VIDEO ANDY IS A SUPER TEACHER.
I'm having issues with my 2013 BMW M5. We changed out both axles but now I'm getting noise in the back when I'm accelerating and getting a drive train malfunction. Any ideas ?
I HAVE A 2012 RAM 1500 4X4 AND AS I AM DRIVING DOWN THE ROAD AND IT HOWLS OR ROARS AS I SPEED UP .if i turn to the right the noise quiets down but it doesnt when i turn left. To me it sounds like its in front end ? Would that actually still be the rear diff. The truck has 169000 miles on it .
I bought a 97 F150 in late 96. It was perfect until a recall and the dealer said they knocked the weight off the driveshaft and had to replace it. After that I had a roaring noise from the rear and took it back. They said it was the Firestone tires and I would have to take it to them. About that time I got a company car and almost never drove my truck. I just lived with the noise for years when I did. Finally had the tires replaced and the noise remained. 97,000 miles later it’s still there. Truck runs great but I can’t find anyone who can tell me what’s causing the noise.
Got my rear diff done by a local highly recommended shop with lower gears and a trutrac installed, makes a howl on decel at 40-45 brought it back says it’s no big deal and such they put some Lucas in and was quiet for a month or two and it’s back been like that for two years hasn’t gotten worse but sure is annoying
The Lucas was a mask for them not setting up the gears properly. Needs to be shimed to the right.
Danny
So you want to move ring gear closer to the pinion?
On a 4x4, if my noise does it in 4hi, would that mean it's NOT the front diff? Could i rule out the front one? Im having hard time telling if sound it's making(on deceleration only), is in the front or back. Any help is appreciated! Thx
My rear was making similar noise and an oil change solved the problem. I was on a road trip and didn't own a dial indicator thus didn't measure backlash.
How much does the labor cost for that?
800
Thank you
Where can I find your services in Malawi?
I have whining noise form rear left driver side at 45 to 70mph could it be the wheel bearing?!
I have a 09 GMC Sierra 2500 gas and I’m at 150k miles. Doing the exact same thing as this ford I can feather the throttle and it’ll make a winding howling noise. Basically only under load but once I let off it goes away. But after watching this video it’s basically everything in the rear end is done for I guess. How bad is it to keep driving it as it is?
Thank you for your video. Would you be able to guide me with this issue I'm having. I have a 05 chevy tahoe, 3.42 gears. GU6,G80. lately when I turn in either direction at a slow speeds, my rear wheels start to lock up and drag as if I was braking but I'm not. I am also starting to hear a growl when coming to slow stop. Any idea on what can be causing this issue and how to remedy. It's my daily driver and need it back on the road. I am also running 37" tires. Your input or advice will be greatly appreciated. Thank you
I have a BMW 530
I have a rear differential humming sound not like this exactly, it's smooth but annoying
Is it really dangerous ??
Can I drive for a long trip ?
Is it just a sound or should I fix it soon ??
It will cost me 3000$
I have a 96 k2500 and mine makes noise when you let up on it not when you're accelerating bearings? Carrier bearing? The truck was dad's and is a pampered garage Queen with 98,000 miles on it
Is it easy to fix differential issue ?
What does this usually cost to repair? Ballpark?
I have a F150 2016 only 182.000km and i have that problem.. is look like a big problem with the Ford F150 a never have that problem with my Ford Ranger 4x4 XLT 2009 and i have 355.000km on its. Can you drive for long time with a hauling noise . like that's ???? 🤔🤔🤔 before readjusting the back lashes or change pinion abd ring Gear.....
I just put yukon gears in my 4wd 2018 1500 sierra denali..there is a different in noise when accelerating and decelerating..is that normal?
+Haven Barner We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Mine makes noise while slowing down but goes away when i speed up. What is the problem. Started after i had pinion seal replaced. Please help thanks
+@RMason1971 We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
Very informative video! You definitely have thorough knowledge of your craft.
I was trying to find out the possible cause of much body noise in the rear of my 2002 nissan pathfinder. Can you help me with a solution to end the annoying noise?
i have a 2018 Jeep Compass 4x4 with 2 speed diff (locking 4wd). Around 35-40 MPH i hear a low hum through the vehicle (can't pinpoint front or back of car.), constant no matter how much or little i accelerate. However, If i turn the Traction control off, it goes away. Any ideas?
+Mark m We wouldn't be able to diagnose an issue like that here, you may want to have a local mechanic take a look at it. Thanks for checking us out! 1aau.to/m/Shop-1AAuto-c
I'm confused about the differential. I'm looking everywhere for a maintenance schedule of differential fluid for my Honda Accord but I can't find anything. Where is the differential located in my car and should I be changing this fluid on regular intervals? Thanks!
Google it.
Its in the transmission on you4 car
What would be causing a shutter when (slowly) accelerateing from a stop? It's worst when making a right hand turn.
Limited Slip differential?
Gong threw the same when from a stop to 40mph found out my differanl is bad
Great video!!! THXS👍
+Mustang Thanks for checking us out! 1AAuto.com
Thank you
Thanks. 2 thumbs up
My 2012 mustang V6 is making noise in the rear end and it’s also leaking oil. The noise it makes is like it’s grinding against something and like a roaring noise as well. How do I fix this and how much will it cost me to fix this? I was told to not drive my car until I fix it. Where should I go and what should I do? Someone please help and give me some ideas. Can I do this job myself?
Speak up or turn the music off
Is that backlash play suppose to be the same for most vehicles?
Can a carrier bearing cause a shuttering, almost a crunchy vibration at slow speeds after a few mins of highway speed? It doesn't do it unless i run 60-70mph for 10+ mins. I also have a humming sound that seems like a wheel or carrier bearing. I'm having a hard time getting the prob diagnosed. It's an 07 AWD Saturn Vue.
Did you ever figure out this problem? I have something similar in a suburban, at highways speed, but it takes like 15 minutes of driving before it happens.
Hi bro thaks the vidio. I have same same problemer. Vito 113 cdi 2.1 2010. Loud soud when i Change the 2 gear. Please help.thanks
What is the name of the part or parts that I would need?
So basically what this is telling me is.. if I don't want to spend several hundred dollars for parts, and several hundred dollars in tools, less a whole day of work and a machinist degree in mechanics, then it is just easier to get a $250 junkyard rear end and be done with it.
Sometimes you got to know when to hold them, and know when to fold them.
Exactly, I have the same situation with my 2010 Silverado that last owner put a Yukon dirá grip and rear gears. It makes the noise when feathering the gas and goes away when I let off. It’s annoying, I really considering just going to the junk yard and swapping out the entire rear axle assembly my self and call it a day. It would be a hell of a lot cheaper fix .
However you gotta hope and pray the junkyard diff dont need any work lol
What was the sound it was making?? A thump?? And did the sound appear when coming to a complete stop like a lunge forward type of feeling??
In the beginning you can hear it but only if you're familiar with the sound. It was howling/low pitched whine.
Outstanding
Thanks for checking us out. 1aauto.com +Mr. Roy
do you have a video on how to remove everything
I have one big question can you help me please
excellent vid. TY
My truck started shaking then when I parked it wouldn’t drive, I reversed then I could go forwards after, any suggestions?
What if the differential locked up