Putting PTM 7950 on my Desktop CPU!
ฝัง
- เผยแพร่เมื่อ 16 มี.ค. 2023
- In this video, I demonstrate the installation of PTM 7950 on my desktop CPU. Please note that this is not a tutorial but rather a test to observe the performance of PTM 7950 over a longer period of time compared to traditional thermal paste.
The reason for my experimentation is that I am tired of the inconvenience of having to change my thermal paste every 6 months to a year, small area to work with and hard to reattach the fans... so I wanted to see if PTM 7950 would be a convenient one-time solution.
The results of my test were surprising,... VERY surprising! Could it be the BEST Thermal Paste Solution?
#ptm7950 #pc #experiment - วิทยาศาสตร์และเทคโนโลยี
What i did was to cut a piece of paper and trim it until it fit my cpu and gpu perfectly then i lined it up on my length of ptm 7950 and cut it exactly so no wastage.
This is EXACTLY what I was looking for. Looking forward to my next CPU upgrade in my mini-ITX system!
I put it on my RTX 4080 and my 5800x3d. Great results on both but the GPU more so because of direct-die cooling.
That's what I've heard as well for GPUs as well! Glad to see someone else is trying it out as well
Before and after temps? Also why is it the small channels are the best ones for cool solutions lol
Would you say the PTM would be better on that 5800X3d than Kryonaut?
@@SuspiciousKoala It's only a little better for the 5800x3d because the CPU uses an IHS. Best results are from direct-die contact. I use it because it better than Kryonaut regardless. I actually forgot to record the before and after temps. It still works better than any paste on a CPU, but even better on a GPU.
On hot laptops, this is as good as LM, or very close. And it gets BETTER overtime apparently, also needs no replacement every year or so, like Thermal Grizzly paste. I have gained permanent measurable turbo with Ryzen Controller + PTM on an Ideapad S145. Even though it's a 30w chip. Idle temps stayed the same at 46 celsius, but with the PTM (usually 30-40 minutes after turning it on), I can stress test on Prime95, which is the most insane test and it takes SO long for boost to lower. Next step is adding more material to the heatsinks, I will add some more small copper plates along the heatpipe (which is ridiculously small on this laptop). I think this will allow the device to turbo for even longer.
what is exactly the temps before and after using the PTM7950 ?
I have PTM7950'ed my DeskMini X300 with a 5700G and i'm very happy with it.
to where I live it, costs the equivalent of 5-8$ depending the the size
Works very well on my 5900x oced to 4.2 - 4.4ghz at 1.15V+_ on an Assassin III and my RTX3080Ti Aorus Master
Hey, could you please tell how did the temperatures fare?
@@manoftherainshorts9075 68-72c under full load. Room AC Temp at 24c.
@@manoftherainshorts9075 With AC on its about low 60s without AC high 60s on all cores
@@omnidyne2434 AC is air conditioning? What's the difference with a normal thermal paste, like Arctic, let's say?
How well does this work at lower idle temps on a desktop cpu? Is it only effective above 45°? Or does it still perform well at 30° or so when idle?
Good question, I don't know if I have the exact knowledge to answer this, but with my personal experience, it actually brought down my temperature from the mid/upper 40's to mid/lower 30's. Truthfully about performance at lower temps I have no idea, but just from the idea that, for me, it keeps it around the mid 30's range idle from the upper 40's seems to be working as it should and if anything performance seems close to the same, maybe slightly better due to that. Key factor for me is longevity and not having to replace it. That probably didn't answer anything and I'm sorry
@@harrisontheeditor Great answer thank you. I think I'll bite the bullet and get some for my iMac which I don't want to have to open up again for another 10 years.
@@edmundmorris3227I'm from Indonesia... I will try to use this PTM 7950 for my macbook pro 2012 md104 . And for the Infinix Note 8 cellphone if there are any advantages😂
So paste above an IHS makes bugger all difference. Paste under an IHS makes a massive difference as you only have a small contact point and die lapping has even more benefit.
Really wish you did a temperature comparison running prime95 or cinebench or something
I did, my 5600x with Arctic MX-6 hits 74c in cinebench. With PTM it hit 73.6c. As others have mentioned, PTM is best for direct die cooling like GPU or laptop CPU.
What size did you buy?
I bought the 80mm by 80mm square, only for the reason if I screwed up I could try again.
Why the hell does this have so many dislikes? Wooow
Probably because you can't see anything! 😄
Not needed on desktop
You're right! Should of used cheese wizz or peanut butter instead 👍
@@harrisontheeditor PTM not needed for desktop
@@ptsp8632 why
@@freddynzeiss high mounting pressure. Ptm serves perfectly gpu dies and laps.. not needed on desktops. Plus is expensive
@@ptsp8632 er no, ptm is actually great when its under high pressure and its not that expensive considering my kryonaut pumps out every 6 months or so.