Thank you!!!! Just sprayed the roof position sensor with WD40 and now i have a fully working roof! Been putting it up and down manually for the last 12 months!!!! Brilliant job sir!
Thank you for filming this! At first I was sceptical if it’s going to help me but turned out that this is by far the best video on how to fix this issue!
I just picked mine up yesterday, tested the roof on the test drive thoroughly, got home and it jammed just as it started raining. Thought I'd bought a money pit until I watched this video. Thank you!
Man this vid was Excellent friend! I'm having issues with the convertible top on my 2010 A5 and I know there's some differences between mine and ur 2006 A4 but there are still many similarities and I hadn't found any vids for mine that even come close to this level of useful information. Thanks, and keep up the good work!
Good video. Very clear. Unfortunately I cleaned the brushes and reinstalled the pump and the roof still does not operate correctly. I don’t have any fault code so I don’t think it’s the sensors. The roof will unlock at the front but that’s it and then sometimes it will lock itself when I push it to the close. But mostly I have to manually lock it. Any suggestions?
Same problem here… worked one day after cleaning the brushes… then it stopped… I think we need to change the motor… cannot find it online… do you know a good online store?
My roof opens a bit like in the video looking for something like this for a while. Only seen ones to manually open or close no computer rest and to change the hydraulic pump. just gave up as it would cost $3k Canadian to fix or $300 for rebuilt pump. A year later now and see this video WOW nice details so I will try these one by one see if it works. Will keep you updated Thank you Alex
@@AlexTheGrumpyOneHi Alex sorry for bothering you. Top opens an inch an stops. Doesnt even close back. Sometimes opens perfectly fine, still does not close . I used a friend's scan tool, did not show any code. If I replace position sensor, do I need to reprogram it, like you did with a laptop. Thanks a lot
My roof quit with an inch more to go down. I found this video but it was beyond my ability. I sent your video to the shop because they could not figure it out. Now they have replaced the switch and control module and need to do a reset. They bought a Audi update and still can't figure it out. Resent them your video in hopes they get this finished. This is going to cost me over $2500 to fix a car not worth that much. I feel like I should have taken it to the dealer. I hope your reset helps them finally finish it. They have had my car over 3 weeks now.
@@AlexTheGrumpyOne Now they said "The windows roll down and the front latch releases when pressing the button. The rear latches are not releasing." So now they hit the button and the top unlatches and the windows go down but the roof doesn't retract. Any ideas?
Hi Alex, thanks for the video. Any ideas on why i get soft top not secure message even when closed. Going over a hump or pothole sets it off. Thanks in advance
Can you possible help me? I have a 2011 S5 Cabriolet...the convertible roof comes down(retracts) no problem. However, when I attempt to raise the roof, the front of the convertible top comes up fine and meets the windshield but the rear of the convertible top is the problem. The rear of the top should raise up to allow the deck lid to slide under but it does not and the decklid stays extended back out over the trunk. My local Audi mechanic thinks it's the hydraulic motor but wouldn't that effect it when it's being put down as well? I'm thinking it's some type of sensor. The car has 59k miles and no warning lights on the dash are illuminated. Thanks in advance...
Life saver mate! Just done mine with compressed air and ultra fine sand paper worked fine but I still have to help it half way through with my hand, any ideas why? It does stop until I help it…
Alex, fantastic video, solved int straight away. do you have any idea why my rear footwells keep filling with water. I had it under a cover except the bonnet and its still getting wet
Your video was very informative. I have an issues with my 2005 audi s4 soft top. The top goes up half way and then comes back down. The rear deck I think is getting stuck causing the roof to go back down and malfunction. Checked for codes and im getting 02000 code(switch position implausible signal). What can be the issue. I dont know when the last time the top has been opened. If you'd be able to help me i'd really appreciate it
Hello! how are you? This is a really helpful video. I also have another issue, because the key once is " locked" does not move any direction. It is seems that is fully stuck the mechanism. I tried to use WD-40 but did not work either. Do you have any other idea? THANKS in advance!
Ive had my 2005 for 7 years and the top stopped responding years ago Today i tested it and it responded!- but only opened a couple inches, like how it was positioned at the very start of the video I’m trying to get it to open, let me know if you’ve run into this !
Hi Alex, thanks for a great video, the explanations are really clear. I have a problem and I'm not sure what exactly is the cause, the roof unlocks at the front, windows go down and the rear window lifts up, so I assume that means the motor is working OK. After that the roof storage lid unlocks but doesn't lift and everything stops then. Would this be a problem with the position sensor? Thanks in advance for your help.
@@AlexTheGrumpyOne I've just now taken off the position sensor to test the connectors. In 90deg position there a connection between the three connectors, in the straight position there's no connection (ohmmeter shows full resistance), which suggests the sensor is doing what it should do. Would you think a full reset might solve the issue?
Really helpful videos, I’ve got a problem with my roof, where the roof unlocks at the front and windows go down. After that you can here the motor working but nothing moves. At which point does the roof storage lid unlock as I think that might be the problem. The motor is definitely working and I’ve replaced the roof position sensor. The rubber washer in the front part of the roof locking mechanism had perished as in your video, so I’ve removed that. In your video you did a reset on your laptop with a program, do you have to do that to enable the roof to operate automatically again. Thank you again for any help you can suggest. Steve
Hello there. Thank you very much for the support :) Yes the hard reset is needed to let the roof know its full travel distance and location. In my case it did help. Can you also have a look at your fluid level on the pump? To see if its on the level or got any leak?
My 2005 A4’s roof will sometimes get stuck when the front of the roof is about to go down into the boot. The pump will continue running, and if I give it the most slightest push with my finger it will continue. It only happens when it’s hot outside and in the sun. Could it require new loading springs or is that something else? I also greased all the hinges and joints with Audi/VW grease. I also cleaned out the pump motor already. I don’t have any error codes either.
Hola Alex, buen trabajo! te comento, he comprado un Audi A4 cabrio del año 06, y tengo un problema con la capota, que no abre ni cierra automáticamente, le he hecho una diagnosis y me salen dos códigos de error: el código de error 02000 y el código 01996, no se si tu puedes ayudarme con el problema Alex, espero tu respuesta, muchas gracias, un cordial saludo.
Thank you very much. I really appreciate your support. I found this Kit that should do the job www.ebay.co.uk/itm/Audi-A4-B6-B7-Cabriolet-Hydraulic-Roof-Motor-Refurbishment-Repair-Kit-8H0959755A-/333636030416?_trksid=p2349624.m46890.l49292
Hey there grumpy Alex! I’m wondering if you have a video on changing the timing chain on my 06 S4 V8? I got Ferraried on this one as you must remove the engine to do the service. Any help is greatly appreciated my friend.
Damn. Mine has just stopped whilst down and it’s raining. I’ve put the cover over as it’s now dark outside, so I will start with sensor in the morning Great help
Hi, awesome video. My roof has started playing up today.When the metal cover part opens up and comes to the end of its travel it all stops and the metal cover part just drops back down on its own as the light on the dash is flashing. Plenty of fluid in the motor.
Hi Alex, fault codes on mine are 02000 01986 00470 00532 Did a manual reset, checked brushes and fluid still not working...any ideas 🤔 roof works on opening until the metal cover fully opens and then everything just calapse's. Any advise would be great!
@valdastamosauskas4708 yes, I have fixed now. My issue was the left hand rear latch, there is a small metal lever in side which gets stuck. Spray some lubricant inside to free it up.
Hi Alex Great work on vid m8. I have a problem with the hydraulic shelf that lifts up to stow the roof. I had to put the roof down manually and it only locked one side, with the other side raised a little. I now can not move it at all. I used the T tool to try to unlock it but it wont budge. Any thoughts would be a great help.
Is there a fuse for the roof? Is there is where is it. Just bought a car roof opened first couple of inches and then stopped. No sound nothing, closed it manually and will be looking at it again tomorrow so just wondering if there a fuse to check before i starting taking it apart.
OURS HAD A MOTOR FAULT DUE TO THE BRUSHES IN THE ROOF MOTOR , seems as if it was a common fault , tap the motor with a rubber hammer , had a new motor which was an update from Audi , GOING STRONGE FOR for the last 14 years , watch out for the rear window coming unstuck on the lower corners after around 16 years old , another common problem . Going to run ours till the Dinosaur Diesel RUNS OUT. Thanks for your video .
Hi, very informative video. I have an A5 convertible that I am not able to open the top because it states that the trunk is opened but it actually is not I a not sure what to do. Can you help?
Hello there. that can be due to faulty sensor in your boot. Have you tried to open and shut it couple of times? Also have you got a extra space shelf unit in your boot?
@@AlexTheGrumpyOne Thanks for getting back to me. I tried shutting a couple times but it did not work. I am going to try to look to see if I got extra shelf unit in my boot.
I've managed to manually closed the roof with the dash tool, but I now get zero response from the roof switch, not even the sound of the pump in the boot. Any advice? Is the motor in the boot the most likely culprit?
Hey Alex. Where would you start on a convertible a4 that when you press the button nothing happens. No motor noises or anything (the top has been manually closed) and there is an orange flashing light on the dash for the convertible roof.
Hello, I want to ask that my roof pump can be opened before it works, but it does not fold the roof. I press it to open the roof, but the roof seems to be closing. Is the opening procedure not set?
hI Alex just watched your video i'm currently working on a 2008 A4 just replaced a drivers side flap motor cleared the fault code however the bed frame is striking the drivers side corner of the roof how do I adjust this or will it adjust when i re configure the roof
Thanks Alex, I faulted my own by propping open and forgetting I’d done it. Fixed now, manual reset, gotta say tho, my one is much cleaner than yours😂diesel convertible? What’s that about?
Great video!! I have the same car and my roof opens half way the back cover opens up as to let the roof in but then drops back down straight away please could you advise.
I have a question, nothing to do with the roof, it's regarding the cruise control not working on my Audi A4 2007 sline convertible. I would really appreciate it if you could help me with this.
Hi can you give me one advise please , I have a issue with my 2006 b7 roof , when I press the button nothing happens , no noise nothing, so when I brought the car(from a action) I found a new reinforcement arch set for roof and also a new sensor , so I will change them tomorrow and after reset the roof and hope will work , if not do you have any other advice, to check the pump ? Or the engine motor ?
No I don’t , I will try that but the yellow light didn’t come on when I push the switch, someone told me if nothing hears when I push the switch maybe is the pump from the boot
Hi Alex. I've go a problem with soft top with this error message on dash: " please lower the storage box" can I use the same procedure that u showed to sort it out?
Hi Alex, I’m still struggling with the problem with my roof, the windows go down and the roof lifts an inch or so and then stops but the motor is still whirring but not doing anything, do you have any idea ?? Many thanks Steve
Hi there. That's the same issue that this one had pretty much. I would recommend starting with a hard manual reset on the roof to be honest. And plug in to see what codes you got at the moment
My top won't unlock manualy from the rear. It clicks but doesn't unlock. When I pull on the button the top goes a couple of inches up then stops. I don't hear the motor in the rear starting at all. Thanks for uploading this I'm gonna try your troubleshooting this week.
@@AlexTheGrumpyOne What’s frustrating is I can’t research this because all the terms I use are used by the same guys making a video to show how to open it manually.
@@AlexTheGrumpyOne wow I’m stupid. I gave up and wrote the last two comments. As I was leaving the garage it hit me. You have to unlock the front and pull the top back for the back to come up. JFC I wasted so many hours. lol I’ll do the pump troubleshooting tomorrow I need a drink
Очень познавательное видео, всё чётко и понятно. У меня крыша тоже не работает, но не могу отсканировать приблудой из Китая. Попробую пройтись по всем датчикам. Спасибо 👍
Spasibo bolhshoie! Da jalko chto u vas netu VCSD, potomushto eto samoia nailutchia programa dlya VAG group. Mojete naiti ne oficialhnoie na ebay za £50.
Salut à tous merci de likez mon commentaire pour qu'il soit vue par le plus de monde possible voilà j'ai une audi a4 cabriolet B7 qui avait le même problème qui est resté légèrement ouvert j'ai tenté comme dans la vidéo de le refermer manuellement exetera bien suivre la vidéo mais cela ne marchait toujours pas pour préciser j'avais laissé la capote ouverte de moitié et elle s'est abaissé toute seule car j'avais retiré le contact suite à cela après cette descendu tout seul elle ne voulait plus se fermer ni s'ouvrir j'ai donc essayé de la remettre à sa place initiale avant qu'elle commence à s'abaisser tout seul et la miracle en voulant continuer le process d'ouverture de la capote elle effectue correctement son cycle cela doit être dû au fait que le capteur ne comprenait pas pourquoi il était censé avoir une certaine position mets en détecter une autre en même temps
Alex, many blessings to you. Your guidance helped. I cleaned the sensor mounted to the folding part of the roof with electrical contact cleaning fluid Part (#8HO 959 613 3300 0801 Position Sensor). That, and a manual retraction of the top, did the trick. Its opening and closing again with a push of a button. Thanks for sharing your knowledge.
Hi. My boot is indicating that it is open when its closed shut and my hood wont function because of it. I don't suppose you know what the problem is do you mate? Thanks
Because sometimes it trued to open and you can hear it starting but then seizing up pretty much. I think its rare for them to completely pack up as it's mainly due to the brushes seizing up, which you can free off or get a new set
Thank you!!!! Just sprayed the roof position sensor with WD40 and now i have a fully working roof! Been putting it up and down manually for the last 12 months!!!! Brilliant job sir!
You are welcome! That's great news 😀
Enjoy your summer time!
Wow! I didnt even remember this. I'll have to do that! I havent been able to close my roof for a month :(
@@zaiville yes I would definitely recommend trying it first 😀
hi
where do u see it in the video?
@@AmirYe ??? He literally shows the location of it in the video and how to take it out? Have you actually tried watching the video?
2 years later and this video is saving me hundreds ❤️ much love bro
Awesome! Happy to hear that 😀
Thank you for filming this! At first I was sceptical if it’s going to help me but turned out that this is by far the best video on how to fix this issue!
Thank you very much 😀 I'm glad that it helped
I just picked mine up yesterday, tested the roof on the test drive thoroughly, got home and it jammed just as it started raining. Thought I'd bought a money pit until I watched this video. Thank you!
Lovely. I'm glad that it helped 😀 well done for sorting it out 😉
Stuck brushers were the problem on my S4. You saved my from having to pay a huge bill. Thank you much!
Awesome! Well done!
Thank you for your feedback
Thank you Alex! The top just stopped working on my 06 Audi S4 cabriolet! The dealer wanted $500 just to look at it! Great video!!
Awesome 😀
Awesome video man. Still helping people many years later. Cheers!
Thank you very much 😀
Really really helpful. Had my Audi roof jam today and thank goodness for your tutorial. Superstar!
Awesome! Glad to hear it and thank you for taking time and writing this 😀 have a wonderful sunny day!
Amazing video Alex, its people like you that save people like us so much money with your time and advise ✌️💯
Thank you very much 😀 I appreciate your support 😀 thanks to people like u, it makes it worth it for me 😀
Thank you for taking the time to educate me about my Audi roof I really appreciate it.
You are welcome. Thank you for leaving coment, as I really appreciate that :) hope this will help you with your roof. Good luck
Ditto! Who takes their time to do all this and make edits and such. I'm very appreciative
Thank you for the support. I really appreciate it. As long as it helps I am more then happy to do it 😊
Fantastically explained and I notice you take your time as well
Thank you I appreciate it!
Yeah I try and explain as much as I can 😀
Great video, my roof failed in exactly the same way yesterday. I will try all this tomorrow and hopefully get it back to normal. Thank you.
Thank you. Good luck. Keep us posted
Brilliant. Will be having a go at this as soon as the rain stops
No worries. And good luck with it 😀
Man this vid was Excellent friend! I'm having issues with the convertible top on my 2010 A5 and I know there's some differences between mine and ur 2006 A4 but there are still many similarities and I hadn't found any vids for mine that even come close to this level of useful information. Thanks, and keep up the good work!
Awesome 😀 thanks you very much for your feedback! Means a lot to me
Good video. Very clear. Unfortunately I cleaned the brushes and reinstalled the pump and the roof still does not operate correctly. I don’t have any fault code so I don’t think it’s the sensors. The roof will unlock at the front but that’s it and then sometimes it will lock itself when I push it to the close. But mostly I have to manually lock it. Any suggestions?
Same problem here… worked one day after cleaning the brushes… then it stopped… I think we need to change the motor… cannot find it online… do you know a good online store?
My roof opens a bit like in the video looking for something like this for a while. Only seen ones to manually open or close no computer rest and to change the hydraulic pump. just gave up as it would cost $3k Canadian to fix or $300 for rebuilt pump. A year later now and see this video WOW nice details so I will try these one by one see if it works. Will keep you updated
Thank you Alex
Awesome 😀 I'm glad that it helps bud! Please do let me know your progress
Just saved me 200 bucks watching this thank you so much
Sweet! That's what I'm here for!
wow .. super helpful man .. Ive had these problems for years thank you !!
You are welcome 😀
Thanks for the amazing video! Never touched a car before and I was able to fix the roof. Hope the best for you!
Awesome! That means a lot to me! Thank you for your feedback
Best explained video on youtube about this issue thank you sir
Thank you! I appreciate your support :)
Hi do you have any solutions for the back of the lid not closing fully.
This is a very thorough video. Thank you for taking the time to do this. Just wondering where do you get the VCDS software from? Thanks!
Thank you 😀
That one I was given by my previous work place
If I saw this guy, I'd take him to a good restaurant. How he took his time and explained everything .
Thank you very much! Means a lot 😀
@@AlexTheGrumpyOneHi Alex sorry for bothering you. Top opens an inch an stops. Doesnt even close back. Sometimes opens perfectly fine, still does not close . I used a friend's scan tool, did not show any code. If I replace position sensor, do I need to reprogram it, like you did with a laptop. Thanks a lot
No worries. I would try and reset it first.
My roof quit with an inch more to go down. I found this video but it was beyond my ability. I sent your video to the shop because they could not figure it out. Now they have replaced the switch and control module and need to do a reset. They bought a Audi update and still can't figure it out. Resent them your video in hopes they get this finished. This is going to cost me over $2500 to fix a car not worth that much. I feel like I should have taken it to the dealer. I hope your reset helps them finally finish it. They have had my car over 3 weeks now.
Hard reset usually fixes most of the issues after replacing the sensors. Check boot storage lead and sensor on it. And also check fluid level
@@AlexTheGrumpyOne Now they said "The windows roll down and the front latch releases when pressing the button. The rear latches are not releasing." So now they hit the button and the top unlatches and the windows go down but the roof doesn't retract. Any ideas?
Hi Alex, thanks for the video. Any ideas on why i get soft top not secure message even when closed. Going over a hump or pothole sets it off. Thanks in advance
Hi there. It can be bad contact in the sensor in the top pillar
Hi Alex, GREAT Video thanks. I have a question regarding the fix at 20:03 on the video. How did you test this component? Thanks in advance. Steve
Thank you pal. Great video in depth on the common issues. Really appreciate it 🙏. Keep up the great work. I liked and subscribed to your channel
Thank you very much for your feedback 😀 I really appreciate it! I'm glad that it helps
Good video. So...Does an OBD reader provide fault codes for the convertible top? I only get engine code fault numbers.
Thank you. I advise a vcds one to get all the codes properly
Thank you for making this video. It got us out of a jam.
Thank you 😀
Can you possible help me? I have a 2011 S5 Cabriolet...the convertible roof comes down(retracts) no problem. However, when I attempt to raise the roof, the front of the convertible top comes up fine and meets the windshield but the rear of the convertible top is the problem. The rear of the top should raise up to allow the deck lid to slide under but it does not and the decklid stays extended back out over the trunk. My local Audi mechanic thinks it's the hydraulic motor but wouldn't that effect it when it's being put down as well? I'm thinking it's some type of sensor. The car has 59k miles and no warning lights on the dash are illuminated. Thanks in advance...
Life saver mate! Just done mine with compressed air and ultra fine sand paper worked fine but I still have to help it half way through with my hand, any ideas why? It does stop until I help it…
Welldone dude garage wanted to charge me £900 to fix it .I just needed to twist it and it started to work
Lovely! Well done! That's what I like to see
Thanks for your video. The fix worked for me and I know what to do if it happens again whilst in my ownership.
That's great! I'm glad ot helped and thank you very much for feedback!
Alex, fantastic video, solved int straight away. do you have any idea why my rear footwells keep filling with water. I had it under a cover except the bonnet and its still getting wet
Thank you very much.
Have you checked the drains?
Your video was very informative. I have an issues with my 2005 audi s4 soft top. The top goes up half way and then comes back down. The rear deck I think is getting stuck causing the roof to go back down and malfunction. Checked for codes and im getting 02000 code(switch position implausible signal). What can be the issue. I dont know when the last time the top has been opened. If you'd be able to help me i'd really appreciate it
Thank you.
I would also check the fluid level in your pump please to see if its OK.
Have you checked your shelf on the boot?
Hello! how are you? This is a really helpful video. I also have another issue, because the key once is " locked" does not move any direction. It is seems that is fully stuck the mechanism. I tried to use WD-40 but did not work either. Do you have any other idea? THANKS in advance!
Do you try back it off a little bit? Also are you turning the red bit out enough?
Mijali? Which mechanism you can't turn with key for manual opening? Front one (over windshield) or back one (behind rear seats)?
Ive had my 2005 for 7 years and the top stopped responding years ago
Today i tested it and it responded!- but only opened a couple inches, like how it was positioned at the very start of the video
I’m trying to get it to open, let me know if you’ve run into this !
hi, can you tell me what part is 02000 please
Thank you this saved us hundreds cleaning the brushes on the motor.
Awesome 😀 u are welcome
Great video I don’t know know why I have this problem with the roof only when it’s
Coldside
Thank you.
That can be due to slight resistance in the sensors. Or metal as well
Hi Alex. Thank you so much for your awesome video. What interface would you recommend for an A4 B7 to use with the VCDS software?
You are welcome 😀
What do you mean by interface?
Vcds light is the best one 😀
How did you replace that rubber grommet under the top lock motor , did you have to remove the whole unit?
Hi Alex, thanks for a great video, the explanations are really clear. I have a problem and I'm not sure what exactly is the cause, the roof unlocks at the front, windows go down and the rear window lifts up, so I assume that means the motor is working OK. After that the roof storage lid unlocks but doesn't lift and everything stops then. Would this be a problem with the position sensor?
Thanks in advance for your help.
Hi there. Thank you
Yes it can be due to it thinking that it's already in different position..
Have you done full reset?
@@AlexTheGrumpyOne No, I don't have the software
@@AlexTheGrumpyOne I've just now taken off the position sensor to test the connectors. In 90deg position there a connection between the three connectors, in the straight position there's no connection (ohmmeter shows full resistance), which suggests the sensor is doing what it should do. Would you think a full reset might solve the issue?
Yes I would try that first to be honest. Well done with the chexk
Really helpful videos, I’ve got a problem with my roof, where the roof unlocks at the front and windows go down. After that you can here the motor working but nothing moves. At which point does the roof storage lid unlock as I think that might be the problem. The motor is definitely working and I’ve replaced the roof position sensor. The rubber washer in the front part of the roof locking mechanism had perished as in your video, so I’ve removed that.
In your video you did a reset on your laptop with a program, do you have to do that to enable the roof to operate automatically again.
Thank you again for any help you can suggest.
Steve
Hello there.
Thank you very much for the support :)
Yes the hard reset is needed to let the roof know its full travel distance and location. In my case it did help. Can you also have a look at your fluid level on the pump? To see if its on the level or got any leak?
I did too the fluid level up. Where’s the best place to get the software to do the hard reset please
Also does that software diagnose all problems
Ok thats good. The best software is vcds to be honest.
Where can I get that from ?
My 2005 A4’s roof will sometimes get stuck when the front of the roof is about to go down into the boot. The pump will continue running, and if I give it the most slightest push with my finger it will continue. It only happens when it’s hot outside and in the sun. Could it require new loading springs or is that something else? I also greased all the hinges and joints with Audi/VW grease. I also cleaned out the pump motor already. I don’t have any error codes either.
I would suggest doing manual reset on it as sometimes can bus system can get confused on them.
Hola Alex, buen trabajo! te comento, he comprado un Audi A4 cabrio del año 06, y tengo un problema con la capota, que no abre ni cierra automáticamente, le he hecho una diagnosis y me salen dos códigos de error: el código de error 02000 y el código 01996, no se si tu puedes ayudarme con el problema Alex, espero tu respuesta, muchas gracias, un cordial saludo.
Very professional 👍👍👍 please send the link for brushes for roof motor
Thank you very much. I really appreciate your support.
I found this Kit that should do the job
www.ebay.co.uk/itm/Audi-A4-B6-B7-Cabriolet-Hydraulic-Roof-Motor-Refurbishment-Repair-Kit-8H0959755A-/333636030416?_trksid=p2349624.m46890.l49292
Hey there grumpy Alex! I’m wondering if you have a video on changing the timing chain on my 06 S4 V8? I got Ferraried on this one as you must remove the engine to do the service. Any help is greatly appreciated my friend.
Hi there. Unfortunately I haven't got any 😞
@@AlexTheGrumpyOne Unfortunately no one else does either lmao! Thanks 🙏 But at least I can fix my top! Splendid!
Damn. Mine has just stopped whilst down and it’s raining.
I’ve put the cover over as it’s now dark outside, so I will start with sensor in the morning
Great help
No worries and good luck to you!
Great video!! Question I there a way to reset the sensors without the software? If not how do I get the software? Thanks
Thank you. Yeah you can disconnect the battery for 5 min. Then do a manual reset with the roof like I explained in the video
Thank You Alex from Michigan USA
You are welcome 😀. Thank you for the support!
Really useful. Thanks for taking the time. Much-appreciated. I take it VCDS is an Audi-specific tool. Is it available to the general public?
You are welcome 😀
Yeah it's for VAG group so Audi, VW, Skoda and Seat.
Yep you can buy one easy 😀
Great video… what is the cost to have someone do exactly what you did? American $?
Hi there. Thank you. Some people spent over £800 fixing things like this
Hi what is the correct hydraulic fluid to top up the pump to the max level. VW power steering green fliud ok?
Never mind. I saw a reply about this further down. Thanks!
Hi, awesome video. My roof has started playing up today.When the metal cover part opens up and comes to the end of its travel it all stops and the metal cover part just drops back down on its own as the light on the dash is flashing. Plenty of fluid in the motor.
Hi Alex, fault codes on mine are
02000
01986
00470
00532
Did a manual reset, checked brushes and fluid still not working...any ideas 🤔 roof works on opening until the metal cover fully opens and then everything just calapse's. Any advise would be great!
@@podwas Hi,were you find the problem?because same at me and fault codes same
@valdastamosauskas4708 yes, I have fixed now. My issue was the left hand rear latch, there is a small metal lever in side which gets stuck. Spray some lubricant inside to free it up.
Outstanding video. Very thorough. Thanks mate 👍🏻
Thank you very much !
Will these errors codes come up using a regular scan tool in the obd2 port ? Thanks
Depends on the tool bud
Hi Alex Great work on vid m8. I have a problem with the hydraulic shelf that lifts up to stow the roof. I had to put the roof down manually and it only locked one side, with the other side raised a little. I now can not move it at all. I used the T tool to try to unlock it but it wont budge. Any thoughts would be a great help.
Is there a fuse for the roof? Is there is where is it. Just bought a car roof opened first couple of inches and then stopped. No sound nothing, closed it manually and will be looking at it again tomorrow so just wondering if there a fuse to check before i starting taking it apart.
OURS HAD A MOTOR FAULT DUE TO THE BRUSHES IN THE ROOF MOTOR , seems as if it was a common fault , tap the motor with a rubber hammer , had a new motor which was an update from Audi , GOING STRONGE FOR for the last 14 years , watch out for the rear window coming unstuck on the lower corners after around 16 years old , another common problem . Going to run ours till the Dinosaur Diesel RUNS OUT. Thanks for your video .
Thank you for the feedback 😀 more helpful info 😀
Hi, very informative video. I have an A5 convertible that I am not able to open the top because it states that the trunk is opened but it actually is not I a not sure what to do. Can you help?
Hello there.
that can be due to faulty sensor in your boot.
Have you tried to open and shut it couple of times?
Also have you got a extra space shelf unit in your boot?
@@AlexTheGrumpyOne Thanks for getting back to me. I tried shutting a couple times but it did not work. I am going to try to look to see if I got extra shelf unit in my boot.
@@patriciafyke641 no problems. Yes have a look at that first please and if not then I will look in to it
I am having the same problem. Says the trunk is open, because the boot lid and the trunk lid won’t fasten.
Thanks mine works perfectly now. Very informative video 👍
That's great 😀 thank you very much
hi
I must to take the roof engine out if I just want to add fluid to it?
Where did you get the Vag Com software and connector ?
Hi there. Hickleys diagnostics is the place for it :)
Thanks bud .
No problems. You got quite few options on there ;) good luck and stay safe
Thanks, I'll be trying this to fix my 08 convertible top.
Awesome 😀
I've managed to manually closed the roof with the dash tool, but I now get zero response from the roof switch, not even the sound of the pump in the boot. Any advice? Is the motor in the boot the most likely culprit?
Can you please advise how to replace Hydraulic Cylinder on the soft top Audi A4 Thank you Stan NZ
Hi there. Unfortunately I never had to do one. Sorry
Thank you I can't find any video's how they are removed I shall keep on searching
Hey Alex, where can we get the VCDS software, very useful info in the video!
Hey Alex. Where would you start on a convertible a4 that when you press the button nothing happens. No motor noises or anything (the top has been manually closed) and there is an orange flashing light on the dash for the convertible roof.
Unlock it manually first and just lift it up a bit and then use a button
@AlexTheGrumpyOne unlock it slightly, try the button or the key in the lock left turned twice and listen for any motor noises?
Start the car and press the roof button to open it
@@AlexTheGrumpyOne tried that. Nothinhb
@JamieMarshall-e1o I would suggest to check the fuses and relays.
Have you scanned it for fault codes?
Txs for your time my friend, I have a 04 Audi convertible
No problems. I'm glad that it helps 😀
Hello, I want to ask that my roof pump can be opened before it works, but it does not fold the roof. I press it to open the roof, but the roof seems to be closing. Is the opening procedure not set?
Yeah it might have wrong info from tye sensor. Try and reset it first please
hI Alex just watched your video i'm currently working on a 2008 A4 just replaced a drivers side flap motor cleared the fault code however the bed frame is striking the drivers side corner of the roof how do I adjust this or will it adjust when i re configure the roof
Hi there.
Is there any air in the system?
Have you done a manual reset on the roof travel. Opening it all the way and shutting it down with that tool?
Thanks Alex, I faulted my own by propping open and forgetting I’d done it.
Fixed now, manual reset, gotta say tho, my one is much cleaner than yours😂diesel convertible? What’s that about?
Haha cheers. That one wasn't mine haha
Hey bud, did you still have the link for the brush replacement kit?
Hi there. That link doesn't work anymore 😞
@@AlexTheGrumpyOne oh man! Do you know who supplies them?
Great video!! I have the same car and my roof opens half way the back cover opens up as to let the roof in but then drops back down straight away please could you advise.
Help please Alex 🙏
Have you had it scanned dot get fault codes?
I have a question, nothing to do with the roof, it's regarding the cruise control not working on my Audi A4 2007 sline convertible. I would really appreciate it if you could help me with this.
Hi there. Yes I can always try 😀
Have you had it scanned to see if there is any fault codes?
Hi can you give me one advise please , I have a issue with my 2006 b7 roof , when I press the button nothing happens , no noise nothing, so when I brought the car(from a action) I found a new reinforcement arch set for roof and also a new sensor , so I will change them tomorrow and after reset the roof and hope will work , if not do you have any other advice, to check the pump ? Or the engine motor ?
My best advise would be to get a scanner and see if there is any faults with it first.
I did that and no codes with the roof which is very strange
@olaruvirgil5522 have you tried disconnecting the battery? Also does the yellow light come on when u pull the switch?
No I don’t , I will try that but the yellow light didn’t come on when I push the switch, someone told me if nothing hears when I push the switch maybe is the pump from the boot
@olaruvirgil5522 it should still have yellow light coming on.
Sounds like your switch might not be working or maybe the fuse or relay is gone.
So if I can find someone with VCDS software, they will be able to help find the fault code that is the source of my top not opening? Thank you.
Yes that will give you a more specific information
Thank you!
Hi, I got a first problem With all windows, they were working perfectly but with no reason they don't roll up or down, what do you think about it?
Hi there. Can you check fuses please first then it also can be wiring issue in rubber seal in driver side door to the body connector.
@@AlexTheGrumpyOne tomorrow I will check it out. I checked all fuse and it is ok. I will let you know if I find something
I hope so
Let me know please. Good luck
Did you find the problem mine don’t work either after CCM got wet I got a new one still nothing fuses look good
Excellent video very helpful and informative thanks
Thank you for your feedback 😀
How did you remove that rubber by the top lock motor did you have to remove the whole housing or did you just break it off and put the new one on
You are simply the best ,and thank you.
Thank you 😀
Hi Alex.
I've go a problem with soft top with this error message on dash: " please lower the storage box" can I use the same procedure that u showed to sort it out?
Hi Alex, I’m still struggling with the problem with my roof, the windows go down and the roof lifts an inch or so and then stops but the motor is still whirring but not doing anything, do you have any idea ??
Many thanks
Steve
Hi there. That's the same issue that this one had pretty much. I would recommend starting with a hard manual reset on the roof to be honest. And plug in to see what codes you got at the moment
My top won't unlock manualy from the rear. It clicks but doesn't unlock. When I pull on the button the top goes a couple of inches up then stops. I don't hear the motor in the rear starting at all. Thanks for uploading this I'm gonna try your troubleshooting this week.
No problems. Let me know how you getting on please
@@AlexTheGrumpyOne Nothing worked man. The back is stuck in place and won’t budge manually.
@@AlexTheGrumpyOne What’s frustrating is I can’t research this because all the terms I use are used by the same guys making a video to show how to open it manually.
@@AlexTheGrumpyOne wow I’m stupid. I gave up and wrote the last two comments. As I was leaving the garage it hit me. You have to unlock the front and pull the top back for the back to come up. JFC I wasted so many hours. lol I’ll do the pump troubleshooting tomorrow I need a drink
Alex, I have cleared the one below the battery, are there any others?
Очень познавательное видео, всё чётко и понятно. У меня крыша тоже не работает, но не могу отсканировать приблудой из Китая. Попробую пройтись по всем датчикам. Спасибо 👍
Spasibo bolhshoie!
Da jalko chto u vas netu VCSD, potomushto eto samoia nailutchia programa dlya VAG group.
Mojete naiti ne oficialhnoie na ebay za £50.
@@AlexTheGrumpyOne если сам не смогу починить, могу приехать к вам в сервис? Где у вас локация?
Mojna budet chtoto pridumaty da. Ya v Ashford, Kent
Is there a kit for the brushes? My brushes are bad I can’t get them free they are stuck .
Yes there was on ebay bud
@@AlexTheGrumpyOne
Do you have the link and a video of how to install them? Thank you for replying to me. I really appreciate any help .
I need your help please, the convertible top on 2012 audi the top good stays in the closed position
Thanx for this Video. Very helpfull and explained very well
You are welcome. I am glad that it is helpful :)
I installed a new roof frame positions sensor. Roof still does not open. Do I need to program the new sensor???
Hi there. You need to do manual reset when you install new ones. So they know the positions when it's shut and open
Salut à tous merci de likez mon commentaire pour qu'il soit vue par le plus de monde possible voilà j'ai une audi a4 cabriolet B7 qui avait le même problème qui est resté légèrement ouvert j'ai tenté comme dans la vidéo de le refermer manuellement exetera bien suivre la vidéo mais cela ne marchait toujours pas pour préciser j'avais laissé la capote ouverte de moitié et elle s'est abaissé toute seule car j'avais retiré le contact suite à cela après cette descendu tout seul elle ne voulait plus se fermer ni s'ouvrir j'ai donc essayé de la remettre à sa place initiale avant qu'elle commence à s'abaisser tout seul et la miracle en voulant continuer le process d'ouverture de la capote elle effectue correctement son cycle cela doit être dû au fait que le capteur ne comprenait pas pourquoi il était censé avoir une certaine position mets en détecter une autre en même temps
Alex, many blessings to you. Your guidance helped. I cleaned the sensor mounted to the folding part of the roof with electrical contact cleaning fluid Part (#8HO 959 613 3300 0801 Position Sensor). That, and a manual retraction of the top, did the trick. Its opening and closing again with a push of a button. Thanks for sharing your knowledge.
Awesome 👌 👏 well done!
Thank you for your feedback
Hi. My boot is indicating that it is open when its closed shut and my hood wont function because of it. I don't suppose you know what the problem is do you mate? Thanks
Hi there. Have you checked if your storage section is down in the boot?
Hi I don’t have have that key to help me lock it down manually, do u know where can I get one ?
Hi there. Yes try and look on ebay please
I am trying to diagnose roof issues on my 95 Cabrio. It pops up the cover about 3 inches and then gives up. Dont know what to do now.
How do you know the motor for top isnt bad?
Because sometimes it trued to open and you can hear it starting but then seizing up pretty much. I think its rare for them to completely pack up as it's mainly due to the brushes seizing up, which you can free off or get a new set
Excellent good information 👏 👌 👍 😀 thank you
Awesome 😀 thank you
Thanks buddy. Very professional
no problems :) Thank you for the support
Nice job. Your video is a keeper. Thanks
Thank you very much! I appreciate it bud!