Worked great for me too. Thanks buddy! I mis-understoond at first. You have to remove the nuts entirely and push the entire assembly inside the door to turn it round. Beautifully smooth now though. Huge thanks for the tip!!! 😁😁
Darren Carter You did just fine it was me not understanding properly lol. My door would still be waking the neighbours in the morning if it weren't for you! Thanks again buddy. Really appreciate it. 😁
Excellent trick mate! just done it on my Vectra C and it works brilliantly! just had to turn the whole bracket once i undone the nuts by pushing it into the door then rotating it back to where it was :D excellent mate!
So are you turning it back the same way to did to start with when you push it inside the door or are you continuing in the same direction to complete the 360 degree turn, or does it not matter?
Great fix, but you should also put some moly grease on the arm - close and open a few times - wipe off excess. Also do up fixings so tiny bit loose, open and close a few times so the checker settles into it's natural alignment then tighten. This will extend the life of the checker considerably
When my door did this I undid the door card. Took the speaker out. Undid the 2 retaining bolts holding this check strap onto the door then undid the two bold holding the door check strap to the body of the car. And then fitted a new one and then put the speaker back etc. I used E (Torx) sockets to undo the check strap bolts. Its stopped the door check strap from click and creaking etc.
Yeah should work mate... I think the part codes are the same... but check 1st... mine is still good after all this time ... so well over a year or so mate...
I was going to do this as my Vectra C drivers door was clunking loudly. Before getting tools out I thought I'd smear on some grease on the tie bar (Castrol LM) and it sorted it out instantly. Not saying this will work for everyone, but worked for me, so worth a try first. Good luck.
Sheraz Malik yeah I did turn it back for the video. As I forgot to record the 1st part.. 1. Undo the hex screw. 2. Turn the check strap arm 180°. 3. Undo the the 2 nuts on the door side. 4. Hold the strap and put it into the door and turn it 180°back around. 5. Line the 2 bolts back up and put the nuts back on.6. Do the hex screw back up.. Should be nice and quiet like new... hope this helps mate..
![[TH] Esports World Cup : Grand Final](http://i.ytimg.com/vi/sedbKhFYDMo/mqdefault.jpg)
![[TH] VCT Pacific Stage 2 - Playoffs Day 2 // PRX vs GEN | DRX vs TLN](http://i.ytimg.com/vi/gmrSk-_ahlA/mqdefault.jpg)
Thank you very much, in 2 minutes I fixed a noise that was annoying me ages... great vídeo!
Cheers for this mate came across this video and it worked put up with that noise for 2 year now
Worked great for me too. Thanks buddy! I mis-understoond at first. You have to remove the nuts entirely and push the entire assembly inside the door to turn it round. Beautifully smooth now though. Huge thanks for the tip!!! 😁😁
Oliver Lewin glad it helped alittle... should have explained abit better....
Darren Carter You did just fine it was me not understanding properly lol. My door would still be waking the neighbours in the morning if it weren't for you! Thanks again buddy. Really appreciate it. 😁
Oliver Lewin no worries mate
Thank you for posting this video, I have cured the irritating noise that I get comments about!
What a fix! Works spot on
Great video man! 5 minutes and my door was like new again
👌👌bang on buddy just tryed it on my vectra and it worked spot on 👍👍👍
Excellent trick mate! just done it on my Vectra C and it works brilliantly! just had to turn the whole bracket once i undone the nuts by pushing it into the door then rotating it back to where it was :D excellent mate!
Yeah it is pretty cool... but a pain to try and do while filming mate.....
So are you turning it back the same way to did to start with when you push it inside the door or are you continuing in the same direction to complete the 360 degree turn, or does it not matter?
Thank you this worked PERFECT!
Dank je wel dit werkte PERFECT!
Thanks finally got rid of that annoying clunk 👍
after putting up with the annoying 'cracking' noise for as long as I can remember 5 mins later it's gone :) thanks for the guide.
Darren Harris thats good..glad it helped...its even better when it doesn't cost you anything lol...
Great fix, but you should also put some moly grease on the arm - close and open a few times - wipe off excess.
Also do up fixings so tiny bit loose, open and close a few times so the checker settles into it's natural alignment then tighten.
This will extend the life of the checker considerably
Cyclone Cyd I did grease it after... I only wanted to show the check strap...thanks for the comment... it's good to know
2 min job and quiet doors again thanks!!
I had the squeak and clunk's from my vectra I used £2 oil from home bargins, that was 2 years ago.
Thanks a lot. That clunk was driving me nuts. Do you know if I can do the same for the rear doors? Seems to have a slight clunk too?
Great little trick worked first time
worked a treat...thanks 👍
cj atkinson no worries mate....
Omg u are the man , just sorted mine been annoying me for ages
You'll still be looking for the noise mate for ages after lol...
@@darrencarter1227 😂😂 defo , I still try to open door a tiny bit then remember its sorted lol
Great, fix. Thanks very much. That was driving me mad & very simple to fix. :-)
stuartmc86 yeah it is a good fix mate....
thank you very much it helped a lot
MrFISH thank you fella....
Good fix. Just done mine 👍
Stephen Wilkinson glad it helped...all little tricks help...
Thanks fella 5 minute job much better now
cd292 glad it helped mate...
Cheers for the video. Do you know if the same thing applies to other Vauxhall's? Specifically the Astra. Thanks
Wobbly wobbly it depends on the year of the car ...and if the check strap is the same as mine the i would say yes...hope this helps..
When my door did this I undid the door card. Took the speaker out. Undid the 2 retaining bolts holding this check strap onto the door then undid the two bold holding the door check strap to the body of the car. And then fitted a new one and then put the speaker back etc. I used E (Torx) sockets to undo the check strap bolts. Its stopped the door check strap from click and creaking etc.
It is always best too fit new parts were possible... this was just a quick fix video... 3 years on and the check strap is still ok...
Great little video! Would you know if the same would work on a 2008 Opel Astra? Thanks
Would probably have to check the part numbers mate... if there the same... can't see why not....
I'd love to know why turning the strap 180° and then back again solves the problem..but hey everyone seems to agree it works so will try it...thanks.
Because its not working against the spring, your turning it too work with the spring, so not as much resistance, that's my guess lol...
My door clunked so loud the whole street could hear it, put some oil on which took 2seconds and its been fine ever since
Will this fix my door falling open aswell?
finally got rid of the annoying noise
THIS REALLY WORKS. I DID IT.
I will try to do My one tomorrow Thank you for your video. Cheap up the good work.
It is easy to do.. just be careful not to drop it inside the door... any thanks ....
Great!!! But it work only for a month. The same crack sound again. Must bay new
Will this work on opel zafira b
And by doing this how long again before it make a noise
Thanks
Yeah should work mate... I think the part codes are the same... but check 1st... mine is still good after all this time ... so well over a year or so mate...
@@darrencarter1227 mine is zafira 2007 thanks
Angelgrey9 the vectra I did it to is a 2007 aswell..
Great hack ✔️✔️
Might just need to go fix mine the now as its just started to click and clunk the last week or two
alanrae1989 yeah do it.. it's a 5 minute job....
Darren Carter yeah i am defo going to do it
still working after 4 montgs👍
Jarrus Killa the car is still ok a year after... so should be fine mate...
I was going to do this as my Vectra C drivers door was clunking loudly. Before getting tools out I thought I'd smear on some grease on the tie bar (Castrol LM) and it sorted it out instantly. Not saying this will work for everyone, but worked for me, so worth a try first. Good luck.
Hello bro did you turned it 360 or turn it back
Sheraz Malik yeah I did turn it back for the video. As I forgot to record the 1st part..
1. Undo the hex screw.
2. Turn the check strap arm 180°.
3. Undo the the 2 nuts on the door side.
4. Hold the strap and put it into the door and turn it 180°back around.
5. Line the 2 bolts back up and put the nuts back on.6. Do the hex screw back up..
Should be nice and quiet like new... hope this helps mate..
works perfectly!;) thanks
Don't work on a vivaro
I haven't tried, it does on astra, signum, vectra, with the same check strap....
I don't understand this😮
Dchats tsit no vectra c dchats Vw itchnk so
Sorry I don't understand!!