How to Replace Front Parking Brake Cable 1998-2011 Ford Ranger
ฝัง
- เผยแพร่เมื่อ 21 ส.ค. 2024
- Buy Now!
New Parking Brake Cable from 1AAuto.com 1aau.to/ia/1ABR...
This video shows you how to replace the front parking brake cable in your 1998-2011 Ford Ranger. The front parking brake cable connects the parking brake pedal to the rear parking brake cables. If this cable has become stuck, broken, or inoperable for any other reason, you won't be able to set the parking brake properly.
This process should be similar on the following vehicles:
1998 Ford Ranger
1999 Ford Ranger
2000 Ford Ranger
2001 Ford Ranger
2002 Ford Ranger
2003 Ford Ranger
2004 Ford Ranger
2005 Ford Ranger
2006 Ford Ranger
2007 Ford Ranger
2008 Ford Ranger
2009 Ford Ranger
2010 Ford Ranger
2011 Ford Ranger
Tools you will need:
• Pry Bar 1aau.to/oa/1AXA...
• 10mm Socket 1aau.to/oa/1AXA...
• 13mm Socket 1aau.to/oa/1AXA...
• 5.5mm Socket
• 7mm Socket 1aau.to/oa/1AXA...
• Trim Tool Set 1aau.to/oa/1AXX...
• Locking Pliers 1aau.to/oa/1AXA...
• Side Cutters
• Ratchet 1aau.to/oa/1AXA...
• Socket Extensions 1aau.to/oa/1AXA...
Subscribe: / @trq
Check out our playlist:
Ford Ranger 1998-2011 3rd Generation: • Ford Ranger 1998-2011 ...
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
√ *Watch the Video*
√ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts
√ *Do it Yourself*
√ *Save Money*
Wow! Great video. I snapped my cable on a 2007 Mazda b2300. I was going to take it to a shop, but I am going to take the time to do it myself. Thanks for the details
Great advice about the PIN to hold the gear in place
Tip, use a FISH TAPE to route your new cable, first go in through firewall to find your way down between the body and the plastic wheel well/ splash gaurd . tape a piece of insulated lamp cord or 12 gauge speaker wire to the FISH TAPE and pull this back into the cabin. Now cut the duct tape off of your wire/ lamp cord and Fish Tape. Set the fish tape aside and tape the brake cable sheath onto your wire/ lamp cord, do this after you have pulled retracted the steel cable flush with the plastic brake cable sheathing and pull this down through from beneath the truck. This guy in the video does a good job , but I found a work around , hope this helps, somebody.
Thanks!
Is there a way to adjust the cable? Mine is loose after new front install.
The cheapest & easy way to fix your brake hook a S hook on cable to frame, takes up slack.
Thanks very much for the video
Thank you nice and easy
Actually this is a good video thanks . For sharing
Thanks ❤️
wow... amazing
Wow, I watched this whole video thinking it would show all the cables, then I realized it only said front cable 🤦
What type of bolts hold the release lever in place. I am missing one and need to buy it.
How do you call te connector clip to joint the old and new cables?
I need that cable where did you purchased the cable
How long did this take ?
Buying Ford Ranger spec parking brake cable connectors all by themselves seems impossible. Gee thanks Ford!
Hermano no te doy trabajo ni colo rompe todo jajaaj
hallcraft got the cable out a lot easier! th-cam.com/video/Sszc6Etwu1M/w-d-xo.html
Cool just start in the middle with no context