2014-2018 Silverado Driveshaft Fix - Performance Driveline - Now We Can Dyno! - Sierra
ฝัง
- เผยแพร่เมื่อ 27 ก.ค. 2024
- Welcome back guys! We are at the final step before getting the final dyno number for my 2014 Silverado.
In this video we are showing how to install the Performance Driveline Single Piece Driveshaft on my 2014 Silverado.
This installation should work for the following vehicles but always double check for your specific model.
2014-2018 Silverado
2014-2018 Sierra
It also may be similar on the following vehicles:
2015-2020 Tahoe
2015-2020 Yukon
2015-2020 Suburban
Note: The performance driveline driveshaft is currently not speed rated - only HP rated but it should be able to handle the higher speeds.
👉🏼 LINKS TO PURCHASE TOOLS & PARTS FEATURED BELOW👈🏼
#PerformanceDriveline #SilveradoDIY #SilveradoDriveShaft
⚠️Try anything shown in this video at your own risk ⚠️
********************************************************************
Associated Videos - AFM DOD Delete Series
********************************************************************
Full DOD delete series below:
Part 1 - Baseline Dyno: • AFM Delete Part 1 - Wh...
Part 2 - What Parts Do You Need • AFM DOD Delete Part 2 ...
Part 3 - Engine Removal: • AFM DOD Delete Part 3 ...
Part 4 - Engine TearDown: • AFM DOD Delete Part 4 ...
Part 5 - Installing New Parts: • AFM DOD Delete Part 5 ...
5A - Cam Phaser Install: • AFM DOD Delete - How t...
5B - Trunnion Upgrade: • How To Upgrade GM Trun...
5C - Lashing HP Fuel Pump: • How To Properly Lash H...
5D - Injector Seals • High Pressure Fuel Inj...
Part 6 - Reinstalling Engine: • AFM DOD Delete Part 6 ...
Part 7 - Tuning and Dyno Run:
Part 8 - Installing Intake Manifold, TB, Air Intake, & Driveshaft:
8A: AIRAID Intake: • Silverado 6.2 AIRAID I...
8B: 6.2 Intake Manifold and TB: • 6.2 Intake Manifold an...
8C: Drive Shaft: • 2014-2018 Silverado Dr...
Part 9 - Tuning and Final Dyno Run:
************************
🔩Parts (Affiliate Links)
************************
For the parts needed to delete AFM check out: • AFM DOD Delete Part 2 ...
GM DriveShaft Bolt (x4 needed) #11548472: geni.us/GM_DriveShaftBolt
GM Yoke Retainer Clips (x2 needed) #23107857: geni.us/GM_YokeRetainerClip
Make Sure to tell Performance Driveline that you heard about them from us!
Single Piece DriveShaft (Note, I went with the high HP version):
geni.us/PD_SinglePieceDriveS
Note: These 2 piece drive shafts are only for 2WD trucks - you must call for a 4x4 version
Two Piece DriveShaft Under 500HP: geni.us/PD_TwoPieceDS_Low
Two Piece DriveShafter Over 500HP: geni.us/PD_2Piece_DS_High
**********************
Tools (Affiliate Links)
**********************
Note: The Max Torque Spec on this 1/4" is 200 in/lbs while the torque spec of the bolts is 216 in/lbs (18ft lbs) but I'm unsure if a larger torque wrench will fit with the socket.
1/4" Torque Wrench: geni.us/GW_14_TorqueWrench
Here is the 3/8" torque wrench, I will try it at some point and report back.
geni.us/GW_38_TorqueWrench
Wobble Sockets: geni.us/WobbleExt
***********************************
⚙️Torque Specs
***********************************
Torque Spec #1: 18 ft-lbs
******************************************
🎬 Recording equipment (Affiliate Links)
******************************************
📷 Video
Canon EOS 80D Digital SLR: geni.us/Canon-EOS80D
----------
Thank you to all of our fans and subscribers for supporting us on our journey!
FOLLOW US ON INSTAGRAM: @THESUNDAEDRIVE
CHECK OUT OUR WEBSITE & BLOG: www.thesundaedrive.com - ยานยนต์และพาหนะ
👍🏻 job. Thanks for the videos. Made it look so much easier than I thought it’d be.
No problem! I expected it to fight me more getting it out for sure.
Thanks that was helpful
No wonder why my truck was shaking at 140mph
Lol that would do it
NICE VIDEO!
Thanks man!
My 2015 pulls hard right up 98mph then it fell on its face,, can't wait to get real drive shaft...
An upgrade is always nice but I do like an exploding shaft
Probably the next upgrade I'll be making. Or towing mirrors.
I did a custom driveshaft on my old Yukon where I swapped in a 4l80. I was prepping for a turbo. Never got to really test the driveshaft because a cop rear ended me and totalled my build.
Aww man that stinks :( I would definitely be pulling a ton of parts out of my truck if it ever gets totaled.
@@TheSundaeDrive I had a build forum thread and thankfully it still drove. I sold it to someone that wanted to fix it up. Took that money and got an AWD 08 Yukon Denali with the 6.2. Been thinking of an LSA blower for a couple years. ;-)
Turned out well at least :)
Can you post the dyno link. Curious about the numbers for my truck. Didn’t see number 9 to have a link. Thanks!
How do you know where to line up the new driveshaft if you don’t have the new one marked .
Thank you
Is the driveshaft the same size as an ext cab too a crew cab I blew mine and I've only found crew cab I have an ext cab
Did this new driveshaft solve any vibration issues you had? TIA
Did it come with a slip yoke?
What's the fastest it gotten with the new drive shaft?
How long ?
Dangs ; what next ; a plastic one from factory all too save a few $$$ . ✊🏻👍👌
how many splines??
Really enjoy the videos, have you thought about adding a rear sway bar on your truck and upgrading the front one. Made a huge difference for the handling on my truck. They are made by Hellwig.
Thanks! Glad you are enjoying it! I have not actually but I will have to look into that for sure! Are you stock ride height?
@@TheSundaeDrive I have a leveling kit on the front using a set of Bilstein 5100 series shocks. Stock ride height on the rear. If you are stock ride height that is how the kit comes for the front and back. If it is for lifted then the company will send you the longer hardware. The front and rear sway bars make a huge difference since their is nothing on the rear and the front one is completely hollow. I got them from Summit racing and they are made by Hellwig.
Ok thanks! These will definitely make it into a video in the future!
Looking forward to it!!
Do you ever drive that truck?
I have 2014 Silverado 5.3 lt 2wd and mine came with the 2 piece drive shaft is the 2 piece any good ?
Oh really? I didn't know any of the OEM drive shafts were two piece. Can't speak to how good it may or may not be unfortunately
Did changing to a performance driveshaft fix any (if any) shakiness you’ve might of experienced at speeds between 65-75mph? I’m just curious because my Chevy has the “chevy shake” sometimes and someone recommended me to change my driveshaft and if I did not want to spend so much yet to just replace the universal joints for new ones.
The two piece drive shafts are supposed to help more with the shake. I don't know notice the shake as often or as severe but I still get some vibration occasionally
Did u ever get that shakiness resolved?
@@AndresRodriguez-hn8oz Did you replace your ujoints yet?
I wonder if you do a lot of towing if this is necessary. I never exceed 100.
I do not believe so. Only needed for high hp and high speed applications from what I understand
Did these issues get corrected? I have a 2017 Chevy Silverado.
No issues with the new drive shaft. Haven't done Dyno runs with it yet tho.
Does the 2014 Silverado 1500 high country 6.2 have the same poor drive shaft ?
I am not 100% sure. Probably but you could compare part numbers to be certain
can i put the same drive shaft you put in a 2017 Chevy 1500 5.3 RWD/2WD?
Would need to check with the company
I just did the dod delete and BTR cam and I’ve run into an issue, was wandering if I could ask for some advice
What's up?
@@TheSundaeDrive due to the driveshaft no one will put my truck on rollers, definitely not a race truck lol just want chop and still be able to pull my car trailer, will a “street” tune do good? I just do not know anyone that has had it done around me
Where can i get one for gmc sierra 1500 2017 ? Or this fits ??
They should be very similar if not the same. The same company has options for your truck as well.
Can you help me pick a drive shaft for my 2018 gmc sierra long bed 2wd
I have been happy with mine. Depends on your power goals. I would talk to the manufacturer to find the best for your needs.
I bought my 2018 new and if it had a speed limiter I never found it. My 2007, 2014, 2016 all were limited to 100. My 2021 is the same-limited to 100. I had heard the reason was the drive shafts would explode. Sad they build shit like this. Been contemplating adding a drive shaft loop or cage or something.....
Some of the trucks have different drive shafts I think. Was the 2018 a z71?
@@TheSundaeDrive I've only had 2wd's......it was a demo so who knows maybe they did something to it before I took delivery
I have a 2015 that regularly exceeds 100.. my driveshaft is acting up are you telling me it’s gonna explode? 🙃
Did the dyna videos ever come out?
Watch are last Silverado update th-cam.com/video/0QaVADj-Hhc/w-d-xo.html
My L86, with longtubes. Hits 115mph a lot. I probably should do the driveline but im curious what speeds people were having issues and or is the L86 packing a stronger one?
Was it factory limited to 100 or no? If not, you probably have a stronger driveshaft. Never a bad idea to upgrade tho
I have been 130mph in mine as far as I know it's factory but it starts getting a little sketchy
@@TheSundaeDrive yea for the first 30k then i chipped it to remove the DOD and raised it to 109. Had the headers and tune done its raised to 125 mph now
I wouldn't keep pushing it personally than without swapping it out
Some trucks have different gearing and I believe different drive shafts. I think the RST models aren't limited at 100 but I could be wrong
do you think this will fit a crew cab 2014, 5.3?
Are you having vibration issues?
cool
Thanks!
@@TheSundaeDriveyou never got the dyno results?
I have a 2 piece high hp 4wd driveshaft being built by them right now but the moronic variant tore through the shop delaying my build. Hopefully it eliminates my 70 mph shake
Definitely update us with how it does for you!
@@TheSundaeDrive here is my update...performance driveline is a garbage company run by liars
@@forgottenchild7935 what happened?
@@winterlounge they shipped me a 1 piece shaft and told me that they don't build 2 piece shafts for my truck. when I referred them to their website that says they do they told me they would do it but no warranty. I wound up installing what they sent me and it eliminated the problem.
is this the drive line company in Bakersfield CA?
Yes 👍👍
Honestly I thought changing drive shaft would be really difficult.
Your shaft looks really big.
It's a truck 🚒
I had a stock shaft and did 180 so 🤷🏽♂️
How much did it cost I need one for my z71
Links are in the description 👍👍
Had the “chev shake” I flushed the trans/ converter twice and it’s finally gone
What fluid did you use and did you do it or the dealership?
What spec fluid did you use?
I recommend amsoil.
@@stevenecto-01xj25Mobil 1
@@winterloungeMobil 1
Anybody got a driveshaft for an 08 GMC Sierra 5.3 1500 crew cab short bed
Aluminum
Check with driveline performance or the driveshaft shop.
You found a one piece shaft for an extended cab truck ?
No one would sell me one that would go over 100mph for a 2wd truck 84inch long shaft .
Is you truck 4wd ?
Mine is 4wd.
@@TheSundaeDrive that makes sense then , with the transfer case it isn't as long
As we mentioned in the video, they didn't guarantee it over 100mph but said they believed it would be ok. So we are going to find out for sure lol.
@@TheSundaeDrive same thing for the high horsepower 2 piece kit ...
No guarantee of speed or power
Hi Do you need some great lighting for your car to help you better driving, off-road. We're the pro auto lighting manufacturer for nearly 20 year and we're looking for sponsorship!
We have multiple videos with light bars from you guys. One on my brother's wrx and two on my truck. If you scroll through you'll find them :)
@@TheSundaeDrive 😁Yes l found them, Kindly ask do you interest in continue with our sponsorship
Add industrial red greese to the front overdrive. It will take out another flaw . Don't run in overdrive. Too much in city driving.
mine exploded due to my ring and pinion
Ouch. How fast were ya going?
@@TheSundaeDrive when i would go 85-90 mph it would shake like if i was riding on a rumble strip then after 90 mph smooth then i would slow down from 90-85 mph it would do the same it was only between that speed
Try again a two piece is the only way that is correct look into critical rotational mass and length it's fuct bad engineering fact