Hello, I have a problem with my pump. I have a 2000 v6 mustang and I use the exact same rebuilt power steering pump that you show in the video. Now my problem is. When I try to push the pulley back on I feel no pressure. The tool itself pushes back out of the middel of the pump again and I can‘t push it back on.
Compare the old pump to the new one. Measure the shaft size to confirm you have the right pump. Test the pulley back onto the old pump. Maybe it got damaged.
@@98RudolphXmas if you installed it on the old pump and it fits and it does not fit on the new pump then the new pump is the wrong one or defective. Or the pulley got damaged and needs to be replaced.
There is prolly air in the fluid. If there is air in it it will be noisy. Jack the car up so you can turn the steering wheel with the engine off. Do that a few times and let it sit till the air separates from the oil.
I am not sure if this is the right one. Call a Ford dealer. Give the part guy your VIN #. Ask for the teflon seal for the power steering pressure hose. Once you get the part number you can cross reference to a Dorman part number. bulletproofdiesel.com/products/teflon-sealing-washer-388898-s-6000044?variant=30876540895328¤cy=USD&gclid=CjwKCAjwyNSoBhA9EiwA5aYlb2_xd6qVUau2tc8aGUebUiwLXEtzenEnRBnFke3IOjBKKqgf2LDbghoCceUQAvD_BwE
Thanks for watching. My Cornwell puller set is similar to this one. www.ebay.com/itm/Blue-Point-CJ132A-Power-Steering-Pump-Alternator-Pulley-Remover-Installer-Kit-/274933065242?mkcid=16&mkevt=1&_trksid=p2349624.m46890.l49286&mkrid=711-127632-2357-0 This is my puller kit webcat.cornwelltools.com/RB5235-Power-Steering-Pulley-Kit-p371692406
Did you have the whinnying noise before the new pump? How about now? I'm about to do mine because of the whine and flush it. I'm so tired of the whine noise! 🥺
My bolts was rusted n the heads broke off from the power steering pump how would i get them out? I tried the screw removal but they not gripping or grabbing
You may need to weld a nut to it. Or remove the entire bracket. Break the pump off with a hammer or just replace the bracket with one from the wrecking yard.
![[UNCUT] “เชื่อมจิต” ใกล้จนมุม อนันต์ชัยเปิดตัวละครลับ เตรียมล้างบาง I คนดังนั่งเคลียร์ l 2 ก.ค.67](http://i.ytimg.com/vi/jeOwG0vt114/mqdefault.jpg)
Extremely helpful!!! thank you.
It would be helpful to know what the adapter to push on the pulley looks like up close.
Consider changing the oil pressure sending unit at the same time, or at least the "O" ring. Great source of leaking oil
Thanks for the info
Good video
I just drilled through the hole on the valve to let the oil “go with the flow” 😊
Hello, I have a problem with my pump. I have a 2000 v6 mustang and I use the exact same rebuilt power steering pump that you show in the video. Now my problem is. When I try to push the pulley back on I feel no pressure. The tool itself pushes back out of the middel of the pump again and I can‘t push it back on.
Compare the old pump to the new one. Measure the shaft size to confirm you have the right pump. Test the pulley back onto the old pump. Maybe it got damaged.
@@chriskolar I did that already everything is fine. They pulley is just spinning and it still will not go on.
@98RudolphXmas ok I will need a more specific answer like.
I installed the pulley correctly and it spins.
The pulley will not fit.
?
@@chriskolar yes that‘s exactly what I meant.
@@98RudolphXmas if you installed it on the old pump and it fits and it does not fit on the new pump then the new pump is the wrong one or defective. Or the pulley got damaged and needs to be replaced.
My new pump still wines.what can we put in the pump to quiet it down?
These pumps use ATF ......
There is prolly air in the fluid. If there is air in it it will be noisy. Jack the car up so you can turn the steering wheel with the engine off. Do that a few times and let it sit till the air separates from the oil.
How is that brand holding up? Getting a reman from XL parts this week
Seems to be working fine. If you do have trashed pump it a good idea to clean out the lines.
Would you happen to have the part number for the nylon o ring?
I am not sure if this is the right one. Call a Ford dealer. Give the part guy your VIN #. Ask for the teflon seal for the power steering pressure hose. Once you get the part number you can cross reference to a Dorman part number.
bulletproofdiesel.com/products/teflon-sealing-washer-388898-s-6000044?variant=30876540895328¤cy=USD&gclid=CjwKCAjwyNSoBhA9EiwA5aYlb2_xd6qVUau2tc8aGUebUiwLXEtzenEnRBnFke3IOjBKKqgf2LDbghoCceUQAvD_BwE
where did u find that pulley tool cause the harbor freight is not working on my 2002
Thanks for watching. My Cornwell puller set is similar to this one.
www.ebay.com/itm/Blue-Point-CJ132A-Power-Steering-Pump-Alternator-Pulley-Remover-Installer-Kit-/274933065242?mkcid=16&mkevt=1&_trksid=p2349624.m46890.l49286&mkrid=711-127632-2357-0
This is my puller kit
webcat.cornwelltools.com/RB5235-Power-Steering-Pulley-Kit-p371692406
@@chriskolar is there a screw where you put the pulley puller ?
Or bolt ?
@@clout-afool1306 when you install the pulley it does screw into the end of the power steering pump shaft
Did you have the whinnying noise before the new pump? How about now? I'm about to do mine because of the whine and flush it. I'm so tired of the whine noise! 🥺
My bolts was rusted n the heads broke off from the power steering pump how would i get them out? I tried the screw removal but they not gripping or grabbing
You may need to weld a nut to it. Or remove the entire bracket. Break the pump off with a hammer or just replace the bracket with one from the wrecking yard.
Yea i did the hammer it worked thank you!!!
@Thunder_aid dang I wish you had a video of that. Thanks for sharing and being the boss.
This will work on a 99 v6 right?
Yes
Thanks
Names specific torque specs. Proceeds to use an uggadugga machine on it. Lol that made me laugh.
He literally used a torque wrench after dude