I Have the same setup for my Scenic2, and got the keys programmed successfully! Can I activate the cruise control with this software? I Have added the Cruise control master that was missing. It now shows up on the instrument panel display, but I am not able to set speed or activate the controller. Thanks for your videos!
When there are immobilizer problems during a key coding process, the vehicle sometimes starts and sometimes doesn't, should I just try to reprogram the keys again or should I reflash the module?
how did you get a connection to the probe? I get rid of the red x but then I get this message Character spacing is invalid and cannot be removed. I just want to read the pin of the cards and then establish the connection for learning and programming and then after that has happened successfully cut the connection.
Hi Brother, My vehicle is Megane 4 1.5 dci 2016 Model Sedan. "Check Auto High Beam" signal appeared on my vehicle. With the ELM 327 Wi-fi device, I read and deleted the DTC fault codes with the car scanner application while the vehicle's engine was running, but these 3 DTC fault codes were not deleted; Dashboard/Instrument Cluster (11 bit) U0182(87) Data bus lamps control module, front - no communication, BCM (11 bit) B15D8(87) and B1568(04) and "Check Auto High Beam" signal still appear on the screen. Do I need to clear the DTC signals with the ignition on and the engine off? What do you think is the fault) Is the UCH faulty? Does the UCH need to be reprogrammed? When it gets dark, the automatic dipped beams are activated, but the light sensor seems to be intact, but the automatic high-to-dipped beam function no longer works. This signal appeared when the vehicle's 12 V battery was close to exhaustion, I measured the battery and read 12.20 Volts with the engine off. I bought a new battery and changed it. But the signal was not deleted. 3 years ago, the car's radio sound was close to dead, and the windows could not be opened and closed, then when the battery was changed, these problems were normal, but now they still continue. The high beams work, the low beams work, they are solid, but there is no transition from high to low to high. It is outputting a fault signal. I'll be glad, if you help me. Take care
HI...I have bought Renolink and a new keycard for my Clio 4. Now the old key does not work at all and I don't have the ISK amd Pin. Is there a way to get them? Please help. Your assistance is much appreciated.
Hello, i have RenoLink 1.99. my interface is connected but when i try to scan, the scan menu goes up to 50%, then it says "Finished scanning" but nothing appears. I don't understand what is the problem... Thanks for your video, do you have any idea about my problem ? Thanks a lot.
I have the app set to reprogramming mode, and the rlink2 multimedia turned off and now it is black, how can i reset the application to default settings and turn it back on?
Hy from what I understand this interface can work on different models brands if you install the dedicate software ? Any way so from description if I want to acces abs and different modules on a renault I need the obdlink ex? I have a problem whit an abs module renault espace 4 and I want to check the sensors wheels. Tha k you
Hello, I don't recommend you to buy this software if you just want to diagnose. It is very good but if you have it in the original version, so if you have the clone version you will have surprises. Regarding what you asked why one can read and another can't, the logical answer is that the MCU is different and the functions of the Hardware are reduced.
@@YOYODiagnostic no error code. Car was fine and it comes to the shop for a spare key. I program a new key and everything went smoothly but car didn't start. Remote working (it's a Renault duster 2020)
Bonjour Question pour savoir si renolink tu a eux déjà marque Trying to connect... Error: Le remplissage n'est pas valide et ne peut pas être supprimé. Diagnostic stopped besoin d aide Merci d'avance
@@YOYODiagnostic Hello, can you please tell me where I can find this and how to do it? Or is it the same step in the Espace as in your video? LG. Kalle
![ทุกครั้งที่หลับตา (Lucid Dream) - AYLA's [ Official MV ]](http://i.ytimg.com/vi/4i1OBAQyv58/mqdefault.jpg)
Hey Yoyo, keep doing your stuff. You're doing a great job! You helped me with a lot of decisions regarding diag. Purchases in the past.
Thank you!.
Hello.
Thanks for watching. 👍
Sall mersi din România:))
Thanks for watching. 👍
I Have the same setup for my Scenic2, and got the keys programmed successfully!
Can I activate the cruise control with this software? I Have added the Cruise control master that was missing. It now shows up on the instrument panel display, but I am not able to set speed or activate the controller.
Thanks for your videos!
Thanks from Algeria 🥰🥰🥰
Thanks
Another helpful video 😀😀😀😀😀😀
When there are immobilizer problems during a key coding process, the vehicle sometimes starts and sometimes doesn't, should I just try to reprogram the keys again or should I reflash the module?
@@maumaumau10000 make a diagnosis first. Lock on the live data and see where the problem is.
how did you get a connection to the probe?
I get rid of the red x but then I get this message Character spacing is invalid and cannot be removed.
I just want to read the pin of the cards and then establish the connection for learning and programming and then after that has happened successfully cut the connection.
Recomand varianta originala creata de Gabi Gafu V1.94.Face tot ce zice.
Hi Brother, My vehicle is Megane 4 1.5 dci 2016 Model Sedan. "Check Auto High Beam" signal appeared on my vehicle. With the ELM 327 Wi-fi device, I read and deleted the DTC fault codes with the car scanner application while the vehicle's engine was running, but these 3 DTC fault codes were not deleted; Dashboard/Instrument Cluster (11 bit) U0182(87) Data bus lamps control module, front - no communication, BCM (11 bit) B15D8(87) and B1568(04) and "Check Auto High Beam" signal still appear on the screen. Do I need to clear the DTC signals with the ignition on and the engine off? What do you think is the fault) Is the UCH faulty? Does the UCH need to be reprogrammed? When it gets dark, the automatic dipped beams are activated, but the light sensor seems to be intact, but the automatic high-to-dipped beam function no longer works. This signal appeared when the vehicle's 12 V battery was close to exhaustion, I measured the battery and read 12.20 Volts with the engine off. I bought a new battery and changed it. But the signal was not deleted. 3 years ago, the car's radio sound was close to dead, and the windows could not be opened and closed, then when the battery was changed, these problems were normal, but now they still continue. The high beams work, the low beams work, they are solid, but there is no transition from high to low to high. It is outputting a fault signal. I'll be glad, if you help me. Take care
HI...I have bought Renolink and a new keycard for my Clio 4. Now the old key does not work at all and I don't have the ISK amd Pin. Is there a way to get them? Please help. Your assistance is much appreciated.
@@openparachute17 you buy the original hardware and software or the AliExpress version ?
YOYO - Renolink 1.87 or 1.99 or 2.10, do they use the same cable?
@@rjunai
Yes
@@YOYODiagnostic TY YOYO !
Can you not see the DTC from Airbag module with Renault Megane II with this?
Hello, i have RenoLink 1.99. my interface is connected but when i try to scan, the scan menu goes up to 50%, then it says "Finished scanning" but nothing appears. I don't understand what is the problem... Thanks for your video, do you have any idea about my problem ? Thanks a lot.
I have the app set to reprogramming mode, and the rlink2 multimedia turned off and now it is black, how can i reset the application to default settings and turn it back on?
Sehr gutes Video danke
Dankeschön. 👍
Than you for your effort and time. Have you got a message "padding is invalid and can not be removed"?
Hello,
no, but if you have problems, write to Gabriel and he will help you. That's if you use the original software.
Interesting video 😀
👍
Great video and I was going to ask if it is worth buying the OBDLink EX rather than SX. But you kind of answered it in the video. 🙂
Hello.
I'm glad I was helpful. 👍
Anyone know how to programme a new injector with renolink?
I don't seem to have that c2i screen in my menus
You have an Original or Clone?
Hy from what I understand this interface can work on different models brands if you install the dedicate software ? Any way so from description if I want to acces abs and different modules on a renault I need the obdlink ex? I have a problem whit an abs module renault espace 4 and I want to check the sensors wheels. Tha k you
Hello,
I don't recommend you to buy this software if you just want to diagnose.
It is very good but if you have it in the original version, so if you have the clone version you will have surprises.
Regarding what you asked why one can read and another can't, the logical answer is that the MCU is different and the functions of the Hardware are reduced.
How can I configure Uch .
Program two keys but it's not starting.
Someone said need to do Uch configuration.
Which error code do you have ?
@@YOYODiagnostic no error code.
Car was fine and it comes to the shop for a spare key. I program a new key and everything went smoothly but car didn't start. Remote working (it's a Renault duster 2020)
@@mohammadalamin208
Look on the live data for immo.
ECU + UCH
Gave me more info
@@YOYODiagnostic can I get your what's up number? So you can assist me?
Hello my renolink is on French were did you get the engl version ?
Thank you.
I have the original Renolink from Gabi Gafu. Contact him. Price is very cheap
Do you have an IDEA how to reset gearbox on Kadjar or Megane IV ?
Hello.
Use Bosch or Hella Gutmann
Bonjour Question pour savoir si renolink tu a eux déjà marque
Trying to connect...
Error: Le remplissage n'est pas valide et ne peut pas être supprimé.
Diagnostic stopped
besoin d aide Merci d'avance
Hello,
Unfortunately, I don't understand what you mean.
English please!
@@YOYODiagnostic hello a question what you encountered the same problem with RenoLink thank you for your help in advance
@@aureliehamed5702
I have not encountered this problem before. If you use the original, ask Gabriel for help, he will help you with this problem.
@@YOYODiagnostic je peux avoir le lien Gabriel merci ou savoir où je peux trouver
How do I get the English version? I only see French in my version.
Thanks!
Take the original one.
Older Xml files are in French, newer ones in English. This are ORIGINAL Renault files, the same used by DDT2000. Renolink interface is in English.
Can you reprogram the rpm with the renolink software? Thanks
Hello.
I don't know but I will try.
Can renolink edit vin code for other modules than the ecm? I need to rewrite the vin on an emm module on a clio 4
Hello,
I don't know.
I know that Reno link can edit UCH .
Wich Version was this?
version v1.87 was used in this video
hello thanks for video . I get INVALID XML file does anyone know about this problem
Sir i want to buy this tool from india
@@abdulimran5644 I'm not a seller. Wrong channel
Muss das auto dabei laufen
Hello, can you also use it to learn the key cards from the Renault Espace IV Bj. 2007 and if so, how does that work?
Hello.
Yes you can use it.
@@YOYODiagnostic Hello, can you please tell me where I can find this and how to do it?
Or is it the same step in the Espace as in your video?
LG. Kalle
@@kaller.9440
Same step.
@@YOYODiagnostic 👍🏼👍🏼👍🏼👍🏼👍🏼