Bhai aap ne jo brushed esc use kiya h vo heat up hota h kya, life kaisi h uski. Or rc car ke liye speed precise control hota h kya as par throttle response
board check karo ek bar. LED blinking ka code upload karo aur onboard LED jal rahi hai ki nahi mujhe batao. Mai instagram pe online rahta hu you can talk there
Thanks for this. By any chance, can you explain the nature of the rx outputs? I want to make my own flight controller and I'm stuck because I don't know what protocol the fs-ia6b uses. Thanks
@@rajatmond I went down the same path. Getting IBus working is so very worth it. That's if you are using a microcomputer like an Arduino. You'll find that PWM has too many errors. Looks like I'm responding to a year old post. lol. Well, anyone that sees this, please give IBus a good try. This method presented here works great.
@@froggytoad7763 yes I used a m7 nucleo dev board(mbed OS). Never got around to using ibus since this is just a hobby and i have to code drivers too if i want to use anything more than pwm.
I used this program but in serial monitor if a print serial.available it is alwaya giving 0 output, and not working, Rx led is blinking in arduino nano. Please help
I did the same, it was working fine.. then it stopped. PPM shows zero signal always... But individual servo pins do work.. only problem is with ppm pin. Why it stopped. Any ideas?
Sir i want to buy this TRANSMITTER which you are using...can i know where i can get it in mumbai ????and other components too like brushless motor ESC etc Please rply
aapne jo 3 saal phle plane bnaya tha jiske 4 parts the usi se inspired mene bhi ek plane taiyar kiya hai aap se jald hi share karunga transmitter aane ke baad flight bhi krunga wingspan 50 inch and length 37 inch 1000 kv motor, rudder and elevator simple 3 ch plane☺☺☺
Nice try , but again it will get more lag , regular flysky receiver is equiped with 32 bit processer , and Arduino is 8 bit , so the latency will be quit high using Arduino , flysky receiver has 76ms latency and may be with Arduino it would be 900ms But at the end of the day Nice try , keep it up
Nice video Recently I used ibusbm library in one of my projects with arduino nano However I noticed that FAILSAFE is not working with ibus. I was wondering if anyone is experiencing the same problem Temporarily I solved it so that I connected channel 5 to one of the input pins on nano so that the program brakes when failsafe is triggered
@@SwapnilNimbalkar I just watched 15 videos with English title and English speaking voice. And guys are from Afrika!! So either go learn English or stop this English titles thing.
![Using an RC Controller with an Arduino [With code and wiring]](/img/n.gif)
thank you for creating this video and sharing knowledge this really help me in my robotics also with a subtitle👍👍👍
Thank you very much for this, and especially for adding subtitles! 👍👍👍
You're welcome 😊
Bro.you are great.Maanna padega. God bless you.
thank you bhai
Are bhai eshe kehate he content 🤩
Thank you so much 😀
Jabardast bro
thanks bhai
@@SwapnilNimbalkar bro heart please ❤️
Спасибо!! очень нужно было ВЫРУЧИЛ!!!!
Very interesting! Do the standard servo ports of the receiver still work or does using ibus deactivate them?
Dear, my nRF module is transmitting data some time what may be problem?
Hi it's not showing anything in the serial monitor, I followed all the steps
Obrigado pelo vídeo, ajudou muito 🪽👍
Sir maine i6s transmeetr hai but muje channel set karna nhi aa rhe hai dron ke liye pliz kuch help kar dijiye
matlab? Aux channels?
Can we use pro mini instead of nano? 🙏
bro, where should i buy depron for rc plane
Search online or may be visit lamington road if you are from Mumbai
Bhai aap ne jo brushed esc use kiya h vo heat up hota h kya, life kaisi h uski. Or rc car ke liye speed precise control hota h kya as par throttle response
Wo faltu ESC hai ekdam. mat lena. costly bhi hai. heat hota hai. isase acchha hai L298N aur arduino se khud bana lo ek ESC
@@SwapnilNimbalkar OK bro main buy karne ki Soch raha tha robu se
@@jonujangid3J its your decision
@@SwapnilNimbalkar bro aap vedio banav na mini brushed esc ka jo ki rc car ke liye Ho or promotional control Ho
Bhai mere me code upload krne ke bad
Serial moniter me kuchh bhi dikh raha hai...pura setting kr chuka hu fir bhi
Koi channel kam bhi nhi kr rha h
board check karo ek bar. LED blinking ka code upload karo aur onboard LED jal rahi hai ki nahi mujhe batao. Mai instagram pe online rahta hu you can talk there
Thanks for this.
By any chance, can you explain the nature of the rx outputs? I want to make my own flight controller and I'm stuck because I don't know what protocol the fs-ia6b uses.
Thanks
It uses iBus protocol,
@@TanM thanks I already figured it out. And I'm programming it for the pwm outputs only. I'll consider iBus later maybe.
@@rajatmond I went down the same path. Getting IBus working is so very worth it. That's if you are using a microcomputer like an Arduino. You'll find that PWM has too many errors. Looks like I'm responding to a year old post. lol. Well, anyone that sees this, please give IBus a good try. This method presented here works great.
@@froggytoad7763 yes I used a m7 nucleo dev board(mbed OS). Never got around to using ibus since this is just a hobby and i have to code drivers too if i want to use anything more than pwm.
@@froggytoad7763 Olá, eu tentei fazer mas não funcionou. Poderia me dar mais alguma dica? Obrigado! =)
I need the code please
Kya reciver se power de ne se Arduino nano damage hoga? Jaise apne diya
nahi
I used this program but in serial monitor if a print serial.available it is alwaya giving 0 output, and not working, Rx led is blinking in arduino nano. Please help
bind ur tx rx
@@SwapnilNimbalkar i have done that rx pin on arduino is also blinking but serial.available is always 0
Thank you very much for this!!!
सर आपने जो ट्रांसमीटर और रिसिवर बनाया था उससे एक प्लेन या फिर ड्रोन उड़ाने के लिए आप कम्पलीट वीडियो बनाए प्लीज
ha uska use karke ek plane banane wala hu mai
bahuti kam ka video thank you
thank you
How to make d i y pwm to PPM encoder using arduino
I did the same, it was working fine.. then it stopped. PPM shows zero signal always... But individual servo pins do work.. only problem is with ppm pin. Why it stopped. Any ideas?
have you turned on PPM output in TX?
@@SwapnilNimbalkar yes
Apology for any typos.. i meant to say that the ibus pin is not working... The individual ppm pins for servos do work. I have enabled PPM.
@@voldoreabhi same is happening for me do you get any solution for this ?
Nice! Can you please explain how you upgraded your TX from 6 to 10 channels? I am afraid of ruining my TX when trying!
Please, I need the code. The link did not open for me
What Protocol iBus iA10b
I'm connect with iA10b it error protocol iA6b please help told me dear .
it should be same
It was so useful that made me subscribe
Thanks
serial monitor par cilk karane port busy aa raha he
dusra kuch aur program run kar rahe ho kya
Great work...
Is it possible to use mpu6050 as a gyro with flysky receiver, for rc car?
Yes should be possible
amazing, but any disadvantages?
Thanks, no disadvantages
Sir i want to buy this TRANSMITTER which you are using...can i know where i can get it in mumbai ????and other components too like brushless motor ESC etc Please rply
Lamington road
@@SwapnilNimbalkar any shop name u know?
Bhai mere receiver me esc lagatehi shot hua aur fir ny chal raha hai reciver
ESC kharab hoga fir
What is the range of this transmitter and reciver in kilomter
should be around 500m
this code is work in arduino uno?
yes
I connect like you I use FS-Ai10B but then I upload error problem uploading to board
fir arduino ka kuch issue hoga. arduino drivers install hai na thik se? com port dikha raha?
@@SwapnilNimbalkar hi you can help me about arduino read FS-Ai10B PWM control servo 180⁰ because usually RC control servo 90⁰ < . How to write code ?
bhai aap 1000 kv ke motor ka plane kitne %throttle me udate ho
wo plane pe depend karta hai. Mera sabse pahla plane jo pusher tha wo sirf 30% throttle pe udta tha.
aapne jo 3 saal phle plane bnaya tha jiske 4 parts the
usi se inspired mene bhi ek plane taiyar kiya hai aap se jald hi share karunga transmitter aane ke baad flight bhi krunga wingspan 50 inch and length 37 inch 1000 kv motor, rudder and elevator simple 3 ch plane☺☺☺
Bhaiya iski range phele kitni thi aur ab kitni ho gayi hogi
isase range utnihi rahegi kam jada nahi hoti
bhai i6x ordered😎from fly robo
good decision
AA cell se receiver chal sakta hai kya
ha
Nice try , but again it will get more lag , regular flysky receiver is equiped with 32 bit processer , and Arduino is 8 bit , so the latency will be quit high using Arduino , flysky receiver has 76ms latency and may be with Arduino it would be 900ms
But at the end of the day
Nice try , keep it up
I dont think there is much latency. And for robotics applications or even RC planes this much of latency is ok.
@@SwapnilNimbalkar yeh you are right , nice try
What is the price of this transmitter (flysky fsi6)
amazon pe dekh lo
Wiring diagram plz not clear in the video
It should be
Great Brother👌👍
Thank you so much 😀
Excellent. Thank you.
welcome
Sir can you make Drone using homemade transmitter and receiver which you have make and flight controller using arduino UNO
I will try for sure
How to convert Transmitter to 10 ch bro
oh. uske liye ye video dekho th-cam.com/video/I8ilTsO74lg/w-d-xo.html
Bhai fpv head tracket bnao please😮❤❤❤❤
Can you write one to use an 8 channel relay board with the FS1A6B and a Nano or Uno?
that should be easy
@@SwapnilNimbalkar that would be awesome!! I've been beating my head against the wall the last couple days trying to figure it out.
@@SwapnilNimbalkar Would you be willing to write it for me?
Bro kya mai (quartz component.co) website se electronic saman manga sakta hu kya ye website safe hai please reply bro
pata nahi yaar, mai pahli bar sun raha hu iska naam
@@SwapnilNimbalkar love you ♥️ bro thanks for reply
@@Rajsmartsolutions Cool
Sir flysky ct6b transmitter ke liye ek receiver banana sikhao
Mera receiver kharab ho gaya he 😢
👍
Jaisa aap dc mind ko bhejta ho
Its So amazing.....
Thanks :)
Bhai aap apna video per code bhej karo
ok
Cool
thanks
Nice video
Recently I used ibusbm library in one of my projects with arduino nano
However I noticed that FAILSAFE is not working with ibus.
I was wondering if anyone is experiencing the same problem
Temporarily I solved it so that I connected channel 5 to one of the input pins on nano so that the program brakes when failsafe is triggered
I really have no idea about that
Thanks
Welcome
Plz make a cargo plane
ok try karunga
Hello dosto... Mere Bhai mere dost paper airplane kut paryanta ala re
aaila banawto banawto nakki
nice video bro
Thanks for the visit
Rimot kantorol. Robot. Banao
ok ok
bhai comment ka jabab Naidia please bhai jabab dijia
kaunsi comment
Sorry bhai jabab mila thank you very much ap reply message nehi aiata
Paisa barbad ho gaya
English clickbait title. Language not english.
dude...........
@@SwapnilNimbalkar I just watched 15 videos with English title and English speaking voice. And guys are from Afrika!! So either go learn English or stop this English titles thing.