How to Setup FS-iA6B with iBUS - Wizard X220 - Flysky FS-i6X (SPracing F3 Flight Controller)
ฝัง
- เผยแพร่เมื่อ 16 มิ.ย. 2024
- You can now support RCwithAdam (and gain special perks!) HERE: ko-fi.com/rcwithadam 🤗
Visit my website here: rcwithadam.com/ 💻
Want to connect your Flysky iA6B receiver (Rx) to your Wizard X220 using iBUS protocol! Well here ya go! (iBUS provides a faster communication between your receiver and your flight controller than PPM (though you won't notice it if your brand new to FPV), which is why you may have had people tell you to switch to iBUS).
STEPS:
1. Plug "servo" connector cable into Rx "ibus" servo port
2. Plug other end of cable into flight controller port
3. Set transmitter "Rx setup" to "ibus"
4. In betaflight; set UART3 to serial RX, save
5. CONFIGURATION: serial based receiver, ibus, save.
6.REMOVE PROPELLERS, connect battery, test function in RECEIVER tab.
Ta da!
▶️ Here's the FULL Eachine Wizard X220 setup video I mentioned: • *NEW* Wizard X220 Setu...
COMMENT BELOW if this was helpful and let me know if you have more questions!
#wizardx220 #betaflight
Support RCwithAdam by purchasing through these links!
Amazon amzn.to/2FHjkwI
Banggood www.banggood.com/custlink/Kvm...
I have a website rcwithadam.com/
-------
RC with Adam GEAR
RADIO: amzn.to/2osIur0 www.banggood.com/custlink/3Kv...
QUAD RECEIVER: amzn.to/2CsvX0C www.banggood.com/custlink/v3v...
AIRPLANE RECEIVER: amzn.to/2OBIqnj www.banggood.com/custlink/GG3...
QUAD PROPS (my fav) amzn.to/2DywVXA www.banggood.com/custlink/GGK...
RC with Adam FILMING GEAR
Main camera amzn.to/2pGZA4L
Action Camera amzn.to/3dVW6DE
Mic amzn.to/2OKoCOB
Camera stand amzn.to/2C4I3uX
--------
Mandatory Disclaimer:
I participate in the Amazon Affiliates program, which means that if you click on one of the above Amazon links and purchase a product on Amazon, I will receive a teeny tiny commission (at no additional cost to you). Also, various other links listed here may be affiliate links, to which this disclaimer also applies.
*REMEMBER, always use caution and your best judgement when building and flying RC aircraft, be a good neighbor, and HAVE FUN!*
-----------
About RC with Adam: Adam makes FUN and HELPFUL videos about Radio Controlled aircraft, tech, and DIY projects! #RCwithAdam - วิทยาศาสตร์และเทคโนโลยี
Do you use the iA6B in your quadcopter?
I'm planning to use a FS-iA6B for an iflight green hornet. Do you think that will work? I am totally new in FPV and very thankful for your Videos! Keep on filming :)
I do, and i cant get rssi please help, i am using ibus
i like how you explain everything so clearly. Punctuation on important stuff is so good.
Adam I literally cannot thank you enough for doing FlySky videos like this oh, it really helps a lot of us out in the community, you are the only one I have found that does these detailed FlySky receiver and transmitter setups it really helps out a lot so once again thank you!
You are very welcome!! Thanks for the feedback! It really helps to know this is useful to people! 😃
THANK YOU SO MUCH I THOUGHT MY DRONE HOBBY WAS DONE YOU HAVE SAVED ME THANK YOU SO MUCHHHHHHHHHHH
Glad hear it! 😉👌
thank you so much ! i've been trying to configure mine for the longest time and you saved me
Glad I could help!
It CAN'T really be THAT easy, can it? This was very helpful, THANK YOU!! 👊🙏👍👍
Thanks for the guide!
At 4:50 I am motivated now I am just gona keet trying
Hey man how are you? Wanted to ask about a little issue, i did all the steps and am using the SPRACING F3 and your same Flysky controller, the only difference is that i am using cleanflight but used the same configuration as you and the software shows that the reciver and transmitter work but the motors wont move.. i only make them move by sliding the bars on the motors tab.
Also i saw that on the video your motors didnt move at the end.. so what step i am missing?
Thanks!
I noticed that at the end of the video when you are using the controls the motors are not working right?
I assume that it's the same steps to connect an FS--IA10B RX? And do all the channels go through one cable?
Cool!
Still in the plane gang lol
Obrigado pelo vídeo, ajudou muito 🪽👍
Same for the ia10b?
Hi Adam, Please help me wire my FS-iA10b receiver to Emax Magnum Mini F4 stack?
The VTX and camera must be connected to the board for the drone to work
I had a rxloss error and realized a uart port was disabled by me accidentally. This saved me
I have this quadX even following all the settings and in betaflight the i6X is recognized nothing happens. Emax Buzz + f4 (firmware omnibusf4) F4 Magnum + FS-i6X + FS-IA6B
Hi how could It be done with an f405?
I DO NOT SEE AN OUTPUT MODE ON MY I6. I cannot find any information either. Is anyone having the same problem?
why UART3 must have the receiver ON, and not UART1 or UART2?
it's the same with me ... but in betaflight it doesn't recognize the remote control im tyro 129 ...
Where to find a connector like that?
Saya punya remote flysky dan receiver, saya mau membuat drone seperti anda, tolong rekomendasi alat apa aja yang dibutuhkan untuk membuat drone
how do i do this on the x220s tho?
is it possible to solder these pins? i dont have that cable and i’m working on a DIY Tyro 119
Yes, definitely. It might be a bit tricky to get all the solder off later though.
hello im having a problem with my fs-i6s remote no serial protocol signal i tried many times to do it but not working some guys said that i need to downgrade and then upgrade to the fs-i6x fireware so that it will work i home someone can help me because im really stuck here
Hello I need help.....I can't get the motors to spin after connecting the transmitter with the flight controller.....all the connections are done but can't seem to be working at all
Did you figure it out
Can you still use the empty channels on the receiver when connecting this way? I want to add 2 forward thrust propeller's to a quadcopter so basically the quadcopter props are just to make it hover. It will pull forward like a plane with the forward facing props
Sounds cool! I'm not sure, but my guess is YES.
@@RCwithAdam1 trying to make sense of it all, a lot to learn at once lol
do you have to leave that thing in and connected to the drone at all times?
Hi! Yes, the receiver must always be connected to the flight controller during flight.
The spracing v3 firmwear is no longer on beta flight config anymore hellp!!
Is there a way to connect another receiver to the main receiver in a way to extend the number of channels available. for example connecting ia6b to another ia6b to get 12 channels?
That's a good question! I'm not sure, but that would be neat. I would think that might be possible with the ibus port.
@@RCwithAdam1 it would be nice if you could make a video on how to do that if you figured it out.
hii, so i did everything like you said on the video and it does actually works when the green thingy is plugged in the drone but when I unplug it from USB and the thingy and try to use the controller motors still don't spin, and for sureee i am missing some steps but I have not clue which one so if you could tell me (if you know ofc) what I am missing I would be so thankful :D
Hi! When you say "green thingy", do you mean the receiver?
@@RCwithAdam1 (wow you are so quick at responding) and yeah, like is the thing you hooked up on the FC so yeah, It should be the receiver (sorry if I am not precise but I am super new at all of this) ow and btw I was searching around and I think I am missing the "rx" like a card that stay on the stack, for receiving the signal, unless it's the "green thingy"
Yes, the green thingy is the reciever. It needs to stay plugged in and connected to the flight controller at all times.
Yes, the green thingy is the reciever. It needs to stay plugged in and connected to the flight controller at all times.
@@RCwithAdam1 ok I won't unplug it but how can I make the motors spin then?
iv done everythin in this tutorial exept the rx setup on the remote as the options are not there on my remote i am using flysky fs-i6 not the fsi6x any help would be good as im stuck now non of the controlls work
Hi! Let's try to get you unstuck! Which version of firmware are you using (you can find that in the system settings menu)?
@@RCwithAdam1 2.0 1-feb-2018
Please how can i bind a flight controller that has a built-in fly sky reciever to a transmitter
Which flight controller?
@@RCwithAdam1 any flights controller that has a built-in reciever and please where can get a cheap transmitter please 👍👍♥️
Does de x220 V3 accepts this Rx?
I'm not super familiar with the X220 v3 flight controller of the top of my head, but yes, it should.
can we use this FC with all in one esc
I think so, but I haven't done it.
how to use naza m lite x1 & x2
Hi! I'm not sure. I haven't used those boards before.
what can i do when my drone doesn´t react to the transmitter
Tell me more details about your setup and issue you're having.
@@RCwithAdam1 i updated my flysky fsi6x to a costum firmware for rssi, but it didn't work, so i downgraded it to the original firmware which i had first, but i bound it many times, but the drone doesn't react to any aux channels(switches, sticks), in the simulator its working, when i bind it, the receiver shows, that its bound, but the drone doesn't react, i set all aux switches correctly up
how to connect i bus to pixhawk
Hi! Sorry, I haven't used pixhawk before. 😕
Hi
Hi!
Yea that didn't work
Hi! which part?
@@RCwithAdam1 has the new update changed this procedure? my receiver no longer connects