HVAC Gas Valve Problems and Solutions

แชร์
ฝัง
  • เผยแพร่เมื่อ 22 ธ.ค. 2024

ความคิดเห็น • 81

  • @takethe101totarzana4
    @takethe101totarzana4 ปีที่แล้ว +2

    The Dumb and Dumber reference was awesome, Lloyd Christmas is somewhere smiling. Thanks for posting Tad, solid video.

  • @rolytech212
    @rolytech212 ปีที่แล้ว +2

    Before taken the inducer motor out I would loosen the burner manifold out. A lot easier

  • @houdini-GT-R
    @houdini-GT-R ปีที่แล้ว +4

    A whole lot of components that I'm not used to I start my new job doing service calls next week I've been doing new construction for the past 8 years I like your content easy to follow and thank you for doing them for us new Jack's doing service calls

    • @TaddyDigest
      @TaddyDigest  ปีที่แล้ว +1

      Good luck my friend wishing you great success
      Thank you for watching

  • @roqueherrera8471
    @roqueherrera8471 ปีที่แล้ว +2

    TAD U ARE THE BEST….. I LOVE YOUR VIDEOS . I going from install to tech and all this is GOLD to me.

    • @TaddyDigest
      @TaddyDigest  ปีที่แล้ว

      You are welcome my friend

  • @emac1111
    @emac1111 ปีที่แล้ว +3

    Great as always. Everything is useful in this video. Go on Tad👍Your subscriber from Azerbaijan

  • @jon3862
    @jon3862 ปีที่แล้ว +3

    You are best of the best 👌 👍 HI from GOLSTAR healing and cooling

  • @thaison773
    @thaison773 ปีที่แล้ว +2

    Thanks for taking the time to make the video.
    I would like to know the size of that gas valve fitting to check for gas pressure with the manometer or if you can share a link of where to buy it.
    Thank you

    • @ikecrook1450
      @ikecrook1450 11 หลายเดือนก่อน

      Your menometer comes with the fittings

  • @hoppychulo1015
    @hoppychulo1015 ปีที่แล้ว +2

    Great video

  • @Eddy63
    @Eddy63 ปีที่แล้ว +2

    Good info Tad ... Thx for posting ...

  • @ikecrook1450
    @ikecrook1450 11 หลายเดือนก่อน +1

    You can't go off the 24 volt to the gas valve I have had them read 24 but had bad common on board if you have analog volt meter it will read 0

  • @ebuzek3648
    @ebuzek3648 ปีที่แล้ว +3

    never adjust a used belt. always install a new belt and then adjust if needed. put a spare or two in a plastic bag.

    • @ikecrook1450
      @ikecrook1450 11 หลายเดือนก่อน +2

      I agree then you get the new one you have to re adjust it again

  • @elmerramirez1215
    @elmerramirez1215 ปีที่แล้ว +1

    Good video man, I’m starting as comercial pm technician and really looking forward to moving up

  • @fazesenso2864
    @fazesenso2864 2 ปีที่แล้ว

    I’m in my 2nd semester of HVac school and ur videos are really good for learning new things

  • @migueldominguez4311
    @migueldominguez4311 ปีที่แล้ว +1

    Great video !
    I have a issue with a gas comercial heather that is used in drive tru canopy !
    And is not turn on
    What could b the issue
    The valve or the main gas ?

  • @howgoodd
    @howgoodd 6 หลายเดือนก่อน +1

    Can you use Teflon instead of thread sealant

  • @miguelrojas3394
    @miguelrojas3394 2 ปีที่แล้ว +1

    I really like the videos the way you explained and thanks for your hard work.

  • @garypoplin4599
    @garypoplin4599 ปีที่แล้ว +1

    Do you have a video on how to clock the meter on a unit like this?

    • @TaddyDigest
      @TaddyDigest  ปีที่แล้ว

      No sir but I can make one

  • @steveomac5001
    @steveomac5001 2 ปีที่แล้ว +1

    It’s looks exactly like a carrier rtu but it has yorks shitty controller. Crazy

  • @antonioquatela4364
    @antonioquatela4364 10 หลายเดือนก่อน +1

    Hello. great content. I Have a question … have you ever experienced a commercial customer call you with a complaint of natural gas odor inside a store? I’m checking these units up and down but am almost out of theories. Is there a premature opening of the gas valve or maybe an induction motor with a leak somewhere? Pretty windy on the roof maybe it needs a exhaust extension brought up higher.

    • @TaddyDigest
      @TaddyDigest  10 หลายเดือนก่อน

      could be a bad board or something like that where its sending power to gas valve and not igniting.
      or regulator vent is leaking

  • @zekenzy6486
    @zekenzy6486 หลายเดือนก่อน +1

    Great video. Thank you for sharing

    • @TaddyDigest
      @TaddyDigest  หลายเดือนก่อน

      my pleasure glad you liked it

  • @aarongray503
    @aarongray503 2 ปีที่แล้ว +2

    Man that was a wealth of knowledge!! Thanks tad! What size of manometer fittings do you typically use? I'm in commercial hvac in Texas but still green.

    • @TaddyDigest
      @TaddyDigest  2 ปีที่แล้ว

      Hey Aaron send me an email thank you so much for joining and being a member
      tadfuller1@gmail.com

    • @TaddyDigest
      @TaddyDigest  2 ปีที่แล้ว

      Glad I could help

    • @ikecrook1450
      @ikecrook1450 11 หลายเดือนก่อน

      They are all standard simple barbed fitting works should come with manometer

  • @glennlockwood7608
    @glennlockwood7608 ปีที่แล้ว +1

    Nice video. How did you manage to have a replacement valve on hand?

    • @TaddyDigest
      @TaddyDigest  ปีที่แล้ว

      I did not I ordered it it came in in 2 days
      I am an hour and a 1/2 from Nashville to an hour
      2 hours from Memphis
      One hour from Jackson
      I have suppliers all over near me

  • @user-ql2bz8on7m
    @user-ql2bz8on7m 6 หลายเดือนก่อน +1

    It was an awesome video thank you

  • @alexibonnet2634
    @alexibonnet2634 2 ปีที่แล้ว +1

    Good video, thank you

  • @stevencovington1776
    @stevencovington1776 ปีที่แล้ว +1

    Hey great video, but did have one question, you normally check your sensor by ohms reading and not continuity?

    • @TaddyDigest
      @TaddyDigest  ปีที่แล้ว

      Normally I check the resistance reading
      Continuity is also a good check

    • @srobeck77
      @srobeck77 ปีที่แล้ว

      Its generally going to be an ohms reading. Continuity is generally for broken wires. Either way, its the same mode on your meter to look for low ohms or O.L.

    • @ikecrook1450
      @ikecrook1450 11 หลายเดือนก่อน

      It will work the same way I use continuity

  • @stevencovington1776
    @stevencovington1776 ปีที่แล้ว +1

    which membership is with the private videos and support?

  • @yodamanrulz176
    @yodamanrulz176 ปีที่แล้ว +1

    Thank you Tod good information all around. However, being new to HVAC, I find it disconcerting when the teacher uses their elbows/fingers to point at something of importance. Please strive to be super clear by using a probe tip or chopstick to point and maintain the point for three or four seconds for a screenshot reference. Thank you.

  • @paulrozinski1488
    @paulrozinski1488 ปีที่แล้ว +1

    Why all the rust on the gas pipes and disconnect switches ?? What area of the US is this ??

    • @TaddyDigest
      @TaddyDigest  ปีที่แล้ว

      Tennessee near Nashville

    • @srobeck77
      @srobeck77 ปีที่แล้ว

      Pipes rust everywhere doesnt matter the location. Even indoors. In salty air, close by oceans, is where metal will rust much faster.

  • @sergioramirez9025
    @sergioramirez9025 2 ปีที่แล้ว +1

    Hey tad quick question how did you know that sensor was supposed to be 10k ohm? I haven't diagnosed that sensor before but on the ODA and SAT MAT sensors RTA sensors etc how do you check those? Is that with a 10 k ohm chart? And has to match the same ambient temp outside???

    • @TaddyDigest
      @TaddyDigest  2 ปีที่แล้ว

      Hey send me an email I have some guides for you
      tadfuller1@gmail.com

    • @TaddyDigest
      @TaddyDigest  2 ปีที่แล้ว

      yes I use a chart I can send you what I have

    • @sergioramirez9025
      @sergioramirez9025 2 ปีที่แล้ว +1

      @@TaddyDigest just did👍

    • @TaddyDigest
      @TaddyDigest  2 ปีที่แล้ว

      Awesome

  • @oscarestrada5509
    @oscarestrada5509 ปีที่แล้ว +1

    Great video bro

  • @roqueherrera8471
    @roqueherrera8471 ปีที่แล้ว +1

    I would hate to ask but do u have any Carrier/Trane/Rheem unit trouble shoot

    • @TaddyDigest
      @TaddyDigest  ปีที่แล้ว

      I'm not sure if I do or not
      I think I do but if I don't I'll have some soon

  • @joebanks174
    @joebanks174 หลายเดือนก่อน +1

    How would you know it was a 10 km sensor?

    • @TaddyDigest
      @TaddyDigest  หลายเดือนก่อน

      from online documentation or manual if with unit

  • @brandoncorrea511
    @brandoncorrea511 2 ปีที่แล้ว +1

    Keep doing these vids. I like it 👍

  • @Ray-wr2wr
    @Ray-wr2wr 11 หลายเดือนก่อน +1

    hi what are they symptoms when dirty burners ?

    • @TaddyDigest
      @TaddyDigest  11 หลายเดือนก่อน +1

      flame will not spread across burners if dirty

    • @Ray-wr2wr
      @Ray-wr2wr 11 หลายเดือนก่อน

      @@TaddyDigest thanks

    • @Ray-wr2wr
      @Ray-wr2wr 11 หลายเดือนก่อน

      @@TaddyDigest what's causing mini explosions /bang on commercial RTU ? gas furnace

  • @hectorgonzalez8185
    @hectorgonzalez8185 ปีที่แล้ว +1

    Good video

    • @TaddyDigest
      @TaddyDigest  ปีที่แล้ว +1

      Thanks Hector
      I have some guides I want
      To send you
      Please send me an email at tadfuller1@gmail.com

  • @juliocastillo1988
    @juliocastillo1988 11 หลายเดือนก่อน +1

    👍👍

  • @abdullah_q8171
    @abdullah_q8171 2 ปีที่แล้ว +1

    Microchannel is Cheap coil .

    • @srobeck77
      @srobeck77 ปีที่แล้ว +1

      I think they actually cost more and are have better efficiency. But on the other hand, they break easier and are harder to repair. We require them to have hail guards on the rooftops units in our facility.

  • @marwinbrown5089
    @marwinbrown5089 9 หลายเดือนก่อน +1

    Awesome video, giveaway

  • @srobeck77
    @srobeck77 ปีที่แล้ว +2

    Your pipe doping skills are lacking here. First, you gotta clean the old threads with a wire brush. Next, apply a thin coat (more is not better). Last, you have to make sure to not get any pipe dope on the end of the pipe (you definitely got a big gob on the end of the pipe) so that it doesn't go into the system and cause problems. A final recommendation is that cogged belts are superior to those straight, standard belts.

    • @TaddyDigest
      @TaddyDigest  ปีที่แล้ว +1

      thanks for watching and for the great tips 😀 👍

    • @srobeck77
      @srobeck77 ปีที่แล้ว +1

      @@TaddyDigest I hope that didnt come as me being a jerk. Its very hard to strike a balance between criticism and not coming off as being insulting or disrespectful. (The same problem happens with text messages too Ive found.) I did very much enjoy your video here and look forward to more.

    • @TaddyDigest
      @TaddyDigest  ปีที่แล้ว

      Friends look out for each other friends say something when others say nothing.
      It's better to say something
      Iron sharpening Iron
      Thanks brother.

  • @pollydor07
    @pollydor07 17 วันที่ผ่านมา +1

    Thanks

  • @mahabubulalamshusom6327
    @mahabubulalamshusom6327 ปีที่แล้ว +1

    Big fan of your videos@Taddy_Digest

    • @TaddyDigest
      @TaddyDigest  ปีที่แล้ว

      Thank you brother. I really appreciate your support and I appreciate you watch the videos