Hi, I have a 2010 Ford Flex and want to turn off the outage for the blinkers, but I don't see 'bdycm' in the list. Is this not available for modification? I do see 'stop and taillight outage configuration'. under GEM/SJB module config. Thanks
I know it’s been a while, my rear driver brake light and turn signal are not working anymore. I’ve installed LED aftermarket tail lights. Question is, changing settings thru BCM module via Forescan will return them back to work as now front turn signal is hyper flashing or do I need to install resistors mandatory? Thank you!
I got a question? I just swap engine from f250 2004 with powerstroke 6.0 with transmission and pcm course to a f350 2008 was powerstroke 6.4. Truck is working now but doesnt show data in the instrumental cluster, do you think rewriting parameters on pcm 6.0 will work in the ins cluster 6.4
Bro, so when Forscan tell you to turn off and turn on. Do you have the engine running all this while or do you just have the key switch on the "ON" position , not really the engine running?
Take a look at my other video on as built data. You will need to go to Ford's website and download the original data. And then go to that module and upload the data to it
I downloaded the license but it’s giving me a message like “you need a license to make changes”. Do you know what I’m missing? What else do I need to use forscan? I downloaded the driver and forscan, all setup, just need the license to go thru.
Welcome. I have a problem after changing the display to 4 " SYNC 1.1, every time it tells me the call for help does not work ... I would like to disable this message. Where should I do it? In APIM or RCM. Block 1 APIM 7D0-01-01 111F 89C0 0355
I would have to look into a little more... Most of the time of there is multiple calibrations in more than one spot you need to disable it in all locations
Thanks. By doing that will it stop any dash errors if I install h7 leds?
Hi, I have a 2010 Ford Flex and want to turn off the outage for the blinkers, but I don't see 'bdycm' in the list. Is this not available for modification? I do see 'stop and taillight outage configuration'. under GEM/SJB module config. Thanks
Is this possible on a Ram 1500 classic warlock?
I know it’s been a while, my rear driver brake light and turn signal are not working anymore. I’ve installed LED aftermarket tail lights. Question is, changing settings thru BCM module via Forescan will return them back to work as now front turn signal is hyper flashing or do I need to install resistors mandatory? Thank you!
Do you have to do 1 at a time or can I do a 4 at once?
Thanks
I changed my whole headlight housing to ANZOS. But the whole housing flickers at random times. How can you fix this?
I got a question? I just swap engine from f250 2004 with powerstroke 6.0 with transmission and pcm course to a f350 2008 was powerstroke 6.4. Truck is working now but doesnt show data in the instrumental cluster, do you think rewriting parameters on pcm 6.0 will work in the ins cluster 6.4
That's hard to say... With the two different platforms and the years apart it may not work. Unless you have the 6.4 cluster and ECM and PCM
Bro, so when Forscan tell you to turn off and turn on. Do you have the engine running all this while or do you just have the key switch on the "ON" position , not really the engine running?
You never have the engine running always just key switch on. Judy to power the modules
I don't have that module.
I have a 21 stx. Is this available for the 21s yet
You can use ForScan but I am not sure if an excel sheet for the as BUILT data has been made yet
Can you show us a video on how to program the vehicle module? I had to replace mine with one I got from ebay and was told I need to flash it.
Take a look at my other video on as built data. You will need to go to Ford's website and download the original data. And then go to that module and upload the data to it
@@jscholl57 that is to flash the entire ECU correct? Thanks
I downloaded the license but it’s giving me a message like “you need a license to make changes”. Do you know what I’m missing? What else do I need to use forscan? I downloaded the driver and forscan, all setup, just need the license to go thru.
Hi Nick! Unfortunately I have never seen this issue... I would make sure you have the latest version of the software installed!
Welcome. I have a problem after changing the display to 4 " SYNC 1.1, every time it tells me the call for help does not work ... I would like to disable this message. Where should I do it? In APIM or RCM.
Block 1 APIM
7D0-01-01 111F 89C0 0355
I would have to look into a little more... Most of the time of there is multiple calibrations in more than one spot you need to disable it in all locations
@@jscholl57 Ok. 🤔
Good