With the old hammer and macro set at 16 the micro adjustment would go well past 5 setting and I could still cock the gun Now i go with the micro past 4:41 4.6 I am unable to cock the gun I noticed the begin wide part of the tungsten is approximately 4mm thicker Would you recommend an other spring
Is it normal to not be able to max out the Micro Adjuster after this install? I can get my macro to 16 and my micro 14 clicks away from the max 5. Its about a little under 4.75 ish
I connected my vice grips directly behind the C1/Hammer seat and even though I wrapped my vice grips in tape, I still scratched the valve rod a bit where the vice grips attached. Is that bad? Do I need to replace the valve rod now? Maybe take some ultra fine grit polishing paper and polish that spot?
No just give a little polishing with some 3M polishing paper you be fine you can find it on ebay Amazon for about 12 bucks for a set of polishing paper I did the same so I just polished everything the rod spring hammer weight and hammer guide and C1
Installed this on my m3 30 cal..micro won't let it me cock at #5..have to back off at #4 to be able to..is there a fix for this to be able to go all the way to #5?
@@utahairgunsworkshop I have a question if I was to buy the new power block plenum kit the whole thing for my mk2 can I just swap block and valve house from my m3 that I have already kill two birds with one stone will it work I'll just use new power block and valve on m3 and the rest will go on the mk2 let me know
Thanks Rob my hammer is stuck inside ill, keep working on it! great video
Did you work it out? What caliber were you using?
With the old hammer and macro set at 16 the micro adjustment would go well past 5 setting and I could still cock the gun
Now i go with the micro past 4:41 4.6 I am unable to cock the gun
I noticed the begin wide part of the tungsten is approximately 4mm thicker
Would you recommend an other spring
Hello I have a question doing this installation what position should the macro and micro wheel be so that we have 6 to 6.5 mm .Thanks
what is the name of this yellow picatinny wrench? And where to buy it? Thanks.
Could you please make the same type of video for the maverick? Thank you.
Hi. When I removed the c1, my valve rod kind of have marks from the vice grip when I clamped it on, is that okay or is that going to cause problems?
Great video
Is it normal to not be able to max out the Micro Adjuster after this install? I can get my macro to 16 and my micro 14 clicks away from the max 5. Its about a little under 4.75 ish
Très bien ,👍
Great job and thanks
No problem
I connected my vice grips directly behind the C1/Hammer seat and even though I wrapped my vice grips in tape, I still scratched the valve rod a bit where the vice grips attached. Is that bad? Do I need to replace the valve rod now? Maybe take some ultra fine grit polishing paper and polish that spot?
No just give a little polishing with some 3M polishing paper you be fine you can find it on ebay Amazon for about 12 bucks for a set of polishing paper I did the same so I just polished everything the rod spring hammer weight and hammer guide and C1
Installed this on my m3 30 cal..micro won't let it me cock at #5..have to back off at #4 to be able to..is there a fix for this to be able to go all the way to #5?
Agreed, It was an easy install.
Hi, how much increase in fps with the change of hammer.?
General guide is this mate.
5.5 mm (.22) between 35 and 55 fps
6.35 mm (.25) between 50 and 80 fps
7.62 mm (.30) between 30 and 60 fps
Does that void warranty? 🤔
No. It doesn't :)
@@utahairgunsworkshop I have a question if I was to buy the new power block plenum kit the whole thing for my mk2 can I just swap block and valve house from my m3 that I have already kill two birds with one stone will it work I'll just use new power block and valve on m3 and the rest will go on the mk2 let me know
We wouldn't recommend it but give us a call if you have any further questions.
What is this installation do for the Impact?
Heavier hammer increases valve dwell. Basically the valve stays open longer and allows for more power.
A heavier hammer or a lighter spring setting should have an equivalent effect.
The kit comes with both for maximum gains
show work is quality pride channel if you can give infinite likes