Thank you so much! I broke my volume button and was hoping to find any phone close to this model, and then I found this! This video is absolutely the shining light in the crapstorm that has been the last two weeks. Thank you!
By far the best disassembly video I have seen. Would please point to where the power IC is? My Note 10 lite doesn't start after not charging and the charging port was not the problem. Cuz I replaced it and nothing changed.
Usually the replacement backs come with adhesive pre installed, but if not you can use 300LSE adhesive or smartphone red tape or other similar adhesives
Hey PBKreviews I recently dropped my note 10 in a drain while it was flowing and I was wondering if it the phone could survive? When I checked the phone I found that the ports was fairly dry and had no water on them however the S-pen was wet and the S-pen compartment was also wet. Is there an opening on the S-pen compartment that might leak onto the board? If so, how long should I leave it to dry or is it just doomed? Sorry for asking a long question
at 00:35 of the video, you show the inside of the backcover which shows a texture that resembles wireless charging. Is there some way to install wireless charging coil on the back, and some possible connector for it? In other words, is it possible to add aftersales wireless charging capability?
Hi, it's not a wireless charging coil on the back plate. You can add aftermarket wireless charging, but it would be one that is attached to the outer back of the phone and connects through your charging port. There would be no connector internally to connect to etc.
Most of the time those cables are used for the antennas (sending signal from lower half antennas to the main board) if I am not mistaken, but I have also seen those type of cables used for touch capacitive keys on sides of phones and other things.
hello, thank you so much for the video!! I am new to smartphone repairs, do you know if the note 10 lite has a different charger port board based on the type of phone (unlocked, etc.) it is, or do all samsung galaxy note 10 lite phones have the same type of charger port board? thank you!
Hi, yes usually different region versions of the phone will have a slightly different sub board or charger port board due to different antenna contacts on the sub board etc. Not always but happens to be the case with motorola and samsung at times.
If the screen is blank and doesnt diplay anything, but its still intact not broken, when open I saw the LCD connector on the motherboard is broken could it be the problem and can it be fixed without doing anything to the screen? Or do I also need to replace my screen?
@@Mikefngarage No problem, no they are different. note 10 plus is a 3040 x 1440 (Quad HD+) display at 6.8" and note 10 lite is 1080 x 2400 (FHD+) at 6.7"
The phone looks like it can withstand accidental water damage. Samsung just didn't want to spend extra money on the IP rating. What your suggestion, note 10 lite or s10 lite?
You're welcome. You need to remove the back plate, then unscrew the screws on the top portion to remove the top black plastic cover and then disconnect the battery cable and the other cable running over the battery. Then you can heat up the adhesive on the battery with a hair dryer by applying the heat from the screen side and then pry the old battery off.
@@janw1982 The old adhesive might hold if it's not tampered with too much but if it's not holding you can apply a new adhesive tape. You can check if there are pre cut ones online (usually sold with back plates) or you can by a roll and cut yourself. But keep in mind it wont be an air tight seal as before unless you purchase a backplate with precut and pre installed adhesive to ensure a strong seal.
@@PBKreviews thank you so much, i think i can do it, but i am a bit afraid With the idea of heating the screen side, i dont want to destroy the screen.
@@janw1982 no you wont damage the screen as long as your not overdoing it, just use a hair dryer (safer than a heat gun) but don't hold it on one area the whole time. Move it around and gently warm it up a bit, you don't need to over do it. You can heat it up a bit and try prying and apply more heat as needed through the process gently to loosen up the adhesive.
agree, s20fe is on the better side, because that it is non glossy. But I could not find any tests of that type of finish. also the price and screen issues makes it very questionable.
Hey PBKreviews...what happens if i accidentally forced the sim ejector tool into the secondary microphone hole, would this cause any damage to the mic or the water resistance protector, especially for this Note 10 Lite model?
Waw.. so brave to disassamble this note10lite.. Btw is there any carbon cooling or similar things that was on note9 that has a heat release function? I just curious what those gold color plates is..
Sorry but do you know by any chance if i can straight up replace the charger module or do i need to soder a new usbc connecter on there ? i know on older models there was a flag set that blocked certian samsung features.
You should be able to replace the sub board which has the charger port with no issues. As long as you make sure to get the same model number version, since different region sub boards would have different antenna configurations and cause service issues.
yes, just make sure to use 99% so its higher alcohol content and dries up quicker. You can also use this: www.ifixit.com/products/ifixit-adhesive-remover?variant=39915173740647 and only apply a little on each side
The coaxial cable connects antenna from the sub board to the main board. You can try to find some online from different phones if they are the same length or similar to replace if one for this model isn't available.
removing the flex cable for them is possible by just lifting out that metal bracket that is holding it in place, but to remove the buttons themselves would require prying off the screen and removing it from that side but would probably cause your screen to get damaged or break.
hello! I have a question. Do you think this phone has water proof ability as note10 and s10. I knew that it cost 20 dollars to get IP rate. Please answer.... From japan.
Hello. How much do you think it'd cost for the display touch combo. ? Considering no edges like note 10, but has an in display fingerprint scanner? Planning to buy one. But, I drop my phone quite often. Broke a Note 8. Couldn't afford it's repair bill. 🙄😬
I have a Samsung Note 10 Lite phone that fell into the water, so the back cameras and the touch stopped, but it works only with the S pen, so what is the problem in your opinion? Please answer my question, and God bless you
There might be corrosion inside over the chips on the board or connectors which is shorting something. You would need to take it apart, dry out any water, brush off any corrosion on chips or connectors with a tooth brush, and put the phone back together to see if it will work. If not, you would have to either replace the screen or there might be damage to the board that is not user fixable.
@@PBKreviews oh I didn't know that.. it's great.. good luck to you.. just a suggestion, if you feel try keeping the phone in portrait.. that feels quite comfortable as a viewer to me
@@youarecorrectiamwrongbecau1338 Thanks. Reason I do in landscape is it gives a closer look overall and easier to see while the work is being done compared to my hands covering the parts a lot and casting shadows over the phone etc.
Well if only the frame is bent/damaged, then only the frame would need to be replaced unless the back plate broke or anything else internally. If not then just the frame would need replacing.
@@Elia_rizkallah well most of the time they sell screen and frame combos which the screen comes preinstalled with the frame. But I'm sure you would be able to find just the frame on ebay or some similar site. However keep in mind, there is a high chance you can break or damage your screen when prying your screen off the frame. You would need to apply heat throughout the process and take your time and gently pry the screen off. It's not easy to get it off without damaging it. So you can try and if it does break then you would need to just get a screen and frame combo but that would run you more at that point.
my samsung note 10 lite had water issues too and i have cleaned and still the phone only vibrate that its is on but the screen does not come up pls what is the solution
Its possible that the screen has got bad or the board. You would need to try a different screen and see if that is the issue, if not then the board might have gone bad from the water damage.
@@PBKreviews I opened mine up because it was splashed. . . The phone worked but was sluggish for about 5 hours until the battery died. Now it won't power on at all. . . After I opened it there was no sign of corrosion. I used 99 percent alcohol to clean and put it back together. . . Still nothing. . . Any ideas?
@@PBKreviews Interesting. There's no ip rating, but this would suggest they made an attempt at at least basic splash resistance... assuming all other entry ports also have something.
Thank you so much! I broke my volume button and was hoping to find any phone close to this model, and then I found this! This video is absolutely the shining light in the crapstorm that has been the last two weeks. Thank you!
You're welcome 😀👍
Hi leva, did replacing the power button solve your issue?
Great video... you need to improve the lighting
Thank you, will do
amazing skills, I am impressed and inspired to buy a smart phone knowing I can DIY repairs.
Thanks :)
By far the best disassembly video I have seen. Would please point to where the power IC is? My Note 10 lite doesn't start after not charging and the charging port was not the problem. Cuz I replaced it and nothing changed.
Does it have cooling system?
Do you need the heat gun to remove the parts or could you just do it without?
you can use a hair dryer, you can also do it without heat but would be harder to pry off
Please mention the name of front camera sensor used in this note 10 lite like its sony made or Samsung own sensor
Great video! Does water get in the insides of the phone easily, or are there any water damage prevention?
Thanks, it should be minor splash proof but not water resistant since I don't see any rubber gaskets around connectors and charger port etc.
It is not splash proof trust me on this. My side keys are broken due to water damage
Hello, what glue do you recommend?
Usually the replacement backs come with adhesive pre installed, but if not you can use 300LSE adhesive or smartphone red tape or other similar adhesives
Hello my friend What kind of track is playing 3:28???
its called Decision and its on the youtube audio gallery under free music
Hey PBKreviews I recently dropped my note 10 in a drain while it was flowing and I was wondering if it the phone could survive? When I checked the phone I found that the ports was fairly dry and had no water on them however the S-pen was wet and the S-pen compartment was also wet. Is there an opening on the S-pen compartment that might leak onto the board? If so, how long should I leave it to dry or is it just doomed? Sorry for asking a long question
Great video. I recently got this phone and so far so good. Did you see any indications that this phone might be water resistant?
It should be splash proof but not if dunked in water etc. from the looks of it.
at 00:35 of the video, you show the inside of the backcover which shows a texture that resembles wireless charging. Is there some way to install wireless charging coil on the back, and some possible connector for it? In other words, is it possible to add aftersales wireless charging capability?
Hi, it's not a wireless charging coil on the back plate. You can add aftermarket wireless charging, but it would be one that is attached to the outer back of the phone and connects through your charging port. There would be no connector internally to connect to etc.
What its the fuction for the white and blue cable? Thanks for your time!
Most of the time those cables are used for the antennas (sending signal from lower half antennas to the main board) if I am not mistaken, but I have also seen those type of cables used for touch capacitive keys on sides of phones and other things.
After this teardown, would you say the Note 10 Lite is splashproof in some ways?
Ya I would say it is minor splash proof but don't think it would survive being dunked in water
Great video.Can i ask if volume buttons and power button can remove from the frame?
Thank you. Yes once you remove the flex cable with button clickers on it from inside the phone, the buttons can be pushed in and removed from inside.
@@PBKreviews Thank you .
@@MrEvgiotis you're welcome
hello, thank you so much for the video!! I am new to smartphone repairs, do you know if the note 10 lite has a different charger port board based on the type of phone (unlocked, etc.) it is, or do all samsung galaxy note 10 lite phones have the same type of charger port board? thank you!
Hi, yes usually different region versions of the phone will have a slightly different sub board or charger port board due to different antenna contacts on the sub board etc. Not always but happens to be the case with motorola and samsung at times.
If the screen is blank and doesnt diplay anything, but its still intact not broken, when open I saw the LCD connector on the motherboard is broken could it be the problem and can it be fixed without doing anything to the screen? Or do I also need to replace my screen?
nice video do you know if the glass screen is the same as the note 10 plus.
Thanks, you mean the type of glass or the screen itself?
@@PBKreviews the screen itself. thanks for reply
@@Mikefngarage No problem, no they are different. note 10 plus is a 3040 x 1440 (Quad HD+) display at 6.8" and note 10 lite is 1080 x 2400 (FHD+) at 6.7"
My Note 10 Lite gets really hot when using basic apps and I have no clue why, is there anything I can do to fix this.
Same issue..🥲
The phone looks like it can withstand accidental water damage. Samsung just didn't want to spend extra money on the IP rating. What your suggestion, note 10 lite or s10 lite?
Yes correct. I would go with the note 10 lite since I would like to make use of the S pen plus overall I liked the build of the note 10 lite
It will NOT, look how the spen compartment have a big hole in it, also the charging port does not have glue/O-ring around it
Thank you for the Video. What steps do i have to Do if i just want to replace the battery?
You're welcome. You need to remove the back plate, then unscrew the screws on the top portion to remove the top black plastic cover and then disconnect the battery cable and the other cable running over the battery. Then you can heat up the adhesive on the battery with a hair dryer by applying the heat from the screen side and then pry the old battery off.
@@PBKreviews thank you very much. :) Do i have to put on some glue when i put on the case after the battery replacement?
@@janw1982 The old adhesive might hold if it's not tampered with too much but if it's not holding you can apply a new adhesive tape. You can check if there are pre cut ones online (usually sold with back plates) or you can by a roll and cut yourself. But keep in mind it wont be an air tight seal as before unless you purchase a backplate with precut and pre installed adhesive to ensure a strong seal.
@@PBKreviews thank you so much, i think i can do it, but i am a bit afraid With the idea of heating the screen side, i dont want to destroy the screen.
@@janw1982 no you wont damage the screen as long as your not overdoing it, just use a hair dryer (safer than a heat gun) but don't hold it on one area the whole time. Move it around and gently warm it up a bit, you don't need to over do it. You can heat it up a bit and try prying and apply more heat as needed through the process gently to loosen up the adhesive.
does note 10 Lite got secondary microphone on the top ? you haven't mentioned it in the video.
Yes, it has one right above the top camera (it's the gold rectangular piece on the board)
Does it have water resistant??? Or p2i coating.. safety from wtaer sprinkle
No!
I got water through the buttons and the device began to reboot constantly
Back panel is plastic or glass? I am very interested in this.
Glastic
So many wonderful samsung handsets with plastic back. It could not be that expensive to make glass back version.
@@reikalasmakaronas2245 idk why they do this but it's not acceptable 😕
agree, s20fe is on the better side, because that it is non glossy. But I could not find any tests of that type of finish. also the price and screen issues makes it very questionable.
@@reikalasmakaronas2245 A72, A52 and A52 5G are non-glossy too
Very helpful..thx so much!
You're welcome!
Hey PBKreviews...what happens if i accidentally forced the sim ejector tool into the secondary microphone hole, would this cause any damage to the mic or the water resistance protector, especially for this Note 10 Lite model?
Hi, no you should be fine, the mic n filter sit above/below the hole so they wont be damaged.
@@PBKreviewsGreat, relieved! Thanks...
Waw.. so brave to disassamble this note10lite..
Btw is there any carbon cooling or similar things that was on note9 that has a heat release function?
I just curious what those gold color plates is..
The gold plate is a copper vapor chamber, has small amount of water vapors inside which transfers heat.
Como hago para quitar la tapa trasera sin que se arrugue
Hi, not sure what you mean.
Sorry but do you know by any chance if i can straight up replace the charger module or do i need to soder a new usbc connecter on there ? i know on older models there was a flag set that blocked certian samsung features.
You should be able to replace the sub board which has the charger port with no issues. As long as you make sure to get the same model number version, since different region sub boards would have different antenna configurations and cause service issues.
@@PBKreviews Good good, gonna check that first, btw i saw that the battery is easier removed with isopropnol alcohol, would you advice it ?
yes, just make sure to use 99% so its higher alcohol content and dries up quicker. You can also use this: www.ifixit.com/products/ifixit-adhesive-remover?variant=39915173740647 and only apply a little on each side
whats the white thin wire on the side of the phone? im curious as I have cut mine while operating
The coaxial cable connects antenna from the sub board to the main board. You can try to find some online from different phones if they are the same length or similar to replace if one for this model isn't available.
@@PBKreviews will do but right now it doesn't seem to affect the phone. wifi and cellular service are okay. any idea why is that?
What is its cooling feature?
Has graphite heat transfer tape as well as a copper vapor chamber which transfer heat.
Is the fingerprint sensor bullshit or is my unit bad?
Any recommendations for a tempered glass if that's hindering the sensor?
try using sceen protector.
Can you please tell me where did you order the screen from ? 👏🏻👏🏻
You can get it from many different places. Ebay, amazon, mobilesentrix.com or other websites.
I would like to see a way to remove the power button. and volume up and down buttons
removing the flex cable for them is possible by just lifting out that metal bracket that is holding it in place, but to remove the buttons themselves would require prying off the screen and removing it from that side but would probably cause your screen to get damaged or break.
where the temperature sensor located?(got the high temp error when charging)
That is probably built into the processor itself
1:36 what connector sir please answer
S pen sensor
Great video,
Thank you
Great video! Thanks a lot!
You're welcome :)
Thank you! :)
you're welcome
Kindly mention or show which sensor is used for front selfie camera like samsung sensor or sony reply ASAP
would be nice if you wouldnt use your fingers on those connections. but great video. Thank you!
:) thanks
hello! I have a question. Do you think this phone has water proof ability as note10 and s10. I knew that it cost 20 dollars to get IP rate.
Please answer....
From japan.
I'm sure it is splash resistant but not sure if it is water resistant. Has good adhesive around back plate but is not rated to be placed into water.
no, he is not waterproof! be carefull. first of all water goes inside thru the hardware buttons!
Hello. How much do you think it'd cost for the display touch combo. ? Considering no edges like note 10, but has an in display fingerprint scanner?
Planning to buy one. But, I drop my phone quite often. Broke a Note 8. Couldn't afford it's repair bill. 🙄😬
The complete screen assembly with midframe runs about $200
I have a Samsung Note 10 Lite phone that fell into the water, so the back cameras and the touch stopped, but it works only with the S pen, so what is the problem in your opinion? Please answer my question, and God bless you
There might be corrosion inside over the chips on the board or connectors which is shorting something. You would need to take it apart, dry out any water, brush off any corrosion on chips or connectors with a tooth brush, and put the phone back together to see if it will work. If not, you would have to either replace the screen or there might be damage to the board that is not user fixable.
@@PBKreviews You are correct, I have cleaned it and the touch is back, but the fingerprint sensor and the back camera are not working yet
Where mic is located?
It's the gold rectangle piece to the left of the charger port at @3:05
which connector is for display?
It's the bottom right cable connected to the small charger port board.
how can i found original display
Watching this on Note 10 lite
Better lighting with larger setup is all that you need to be a millionaire. I meant subscribers.
Thanks, have already upgraded the lighting and setup on newer videos. :)
@@PBKreviews oh I didn't know that.. it's great.. good luck to you.. just a suggestion, if you feel try keeping the phone in portrait.. that feels quite comfortable as a viewer to me
@@youarecorrectiamwrongbecau1338 Thanks. Reason I do in landscape is it gives a closer look overall and easier to see while the work is being done compared to my hands covering the parts a lot and casting shadows over the phone etc.
so the water cooling is in my note 10 lite
thats cool and that explains why dont get really hot like my old samsung s7
Yup, it has good cooling
Nice
❤❤❤super thx
water cooling system is available in note 10 lite 🤔
Thank you
you're welcome
my phone got bent but screen work a 100% what parts should i replace other than the frame
Well if only the frame is bent/damaged, then only the frame would need to be replaced unless the back plate broke or anything else internally. If not then just the frame would need replacing.
@@PBKreviews becouse evrey store i went too they said samsung cant sell them frame only is that right bro
@@Elia_rizkallah well most of the time they sell screen and frame combos which the screen comes preinstalled with the frame. But I'm sure you would be able to find just the frame on ebay or some similar site. However keep in mind, there is a high chance you can break or damage your screen when prying your screen off the frame. You would need to apply heat throughout the process and take your time and gently pry the screen off. It's not easy to get it off without damaging it. So you can try and if it does break then you would need to just get a screen and frame combo but that would run you more at that point.
@@PBKreviews thanks
@@Elia_rizkallah you're welcome
Thanks
Anyway to add wireless charging?
You would be able to use one of these wireless charging adapters. amzn.to/2UMGBXp
Damn good video.
Thanks!
my samsung note 10 lite had water issues too and i have cleaned and still the phone only vibrate that its is on but the screen does not come up pls what is the solution
Its possible that the screen has got bad or the board. You would need to try a different screen and see if that is the issue, if not then the board might have gone bad from the water damage.
@@PBKreviews alright thank you
@@ayobamijohnson4124 You're welcome
@@PBKreviews I opened mine up because it was splashed. . . The phone worked but was sluggish for about 5 hours until the battery died. Now it won't power on at all. . . After I opened it there was no sign of corrosion. I used 99 percent alcohol to clean and put it back together. . . Still nothing. . . Any ideas?
I have this kind of phone
Do you notice any sort of rubber that protects the phone from water?
There are some here and there. I would presume it would be minor splash proof but don't think it would survive being dunked in water. Not sure though.
Am I seeing things or does the sim tray have a rubber seal?
Yea it has a rubber gasket
@@PBKreviews Interesting. There's no ip rating, but this would suggest they made an attempt at at least basic splash resistance... assuming all other entry ports also have something.
@@MariuszMazur ya, happens many times that phones dont officially get an ip rating but still have some water resistance
Как оцените сборку ,лучше чем среднебюджетные телефоны от этого бренда?
Ya it is a good solid build. I would say its a better build than most in the same tier.
My phone won't charge😭
спасибо, получилось! ощущения как от первого секса - руки дрожат, вспотел, но аккумулятор заменил. Думал 15 минут прошло, оказалось уже час пролетел))
you're welcome :)
You needs better light, the light looks better on the old video of ( Galaxy Note 10 ) Disassembly Teardown
आईलीड मदरबोर्ड कंडक्टर डिस्प्ले कनेक्टर
not sure what you are saying
Nice