BMW MINI Cooper R50 Airbag Light Reset Procedure
ฝัง
- เผยแพร่เมื่อ 22 ก.ย. 2015
- For those getting the airbag light when removing their seats or if the light has come up on the dash of your Mini Cooper. This is removal process for the R50. This process should work for other models up to the R60 with this device.
Order on Amazon: amzn.to/2NW6rBv
Dealer wanted me to bring in for a "faulty seat pad sensor" and was a $900 quote. I got this code or light because I unplugged seat connections when vacuuming. Unplugging your seat connectors (underneath seats) without disconnecting battery will trigger this warning light.
2002 Mini Cooper R50 - 85,672 miles
Autel Autolink AL619 - Great scanning tool and excellent live data. Can be updated from time to time on www.auteltech.com
Order on Amazon: amzn.to/2NW6rBv - ยานยนต์และพาหนะ
![USAB Showcase: Australia vs USA [OFFICIAL STREAM]](http://i.ytimg.com/vi/keiEr_MOaSQ/mqdefault.jpg)
Thank you for the video. This was so easy and it worked!!!
Hey, Cindy. How did you figure out where to plug the unit into the Mini?
Hi buddy, Thanks for information. May I ask where did you buy or purchase the Autolink?
Does it work with Mini R56 (2007)? Thank you.
my autolink won't make the airbag light to blink
P.S. What I'm asking is, how do you reconnect the seat connector. So that I can reset the light using the Autolink. Thanks again.
StarletteNyte Cain see below
Bonjour a tous alors pour ma part je viens vers vous pour indiquer que ce n`est forcement un probleme du a l`airbag je m`explique j`ai demonter mon volant pour le changer et forcement des brancher l`airbag mais sans debrancher la batterie chose qu`il ne faut surtout pas faire sur une mini cooper s r53 2004 et apres remontage le voyant airbag et rester allumer apres plusieurs essaie avec differente tablette diag j`ai tester 5 tablettes differentes et une seule ma reveler le probleme le probleme me disant qu`il y avais un probleme d`isolation de batterie alors j`ai donc demonter ma batterie tous nettoyez et je me suis apercu que la borne negatif alors la je parle du fil noir celui qui est serrer sur la borne la partie cuivre etait desserer avec certainement les vibrationsdu au temps puis ensuite remis la borne sur la batterie avant j`ai mis un peu de graisse sur les deux bornes remonter puis ensuite debrancher tous les intruments que vous auriez vous meme connecter peu importe ce que sais car il faut peu de chose qui va aux calculateur pour creer des problemes furtif j`ai donc connecter avec le diag de marque AUTEL AUTOLINK AL 619 abs srs que l`on trouve sur amazon vous suivez la procedure et cela fonctionne parfaitement retirer aussitot plus de probleme ayant beaucoup galerer pour trouver le probleme j`espere que cela aidera tous ceux qui en aurons besoin bonne chance a tous
I have 3 warning lights on..I replaced the clutch.so I had to disconnect some sensors..after I put everything back the lights came on..
Antonio Gates what sensors did you have come on?
my obd ii reader keeps on saying "try (mode 02) please wait" then will sit there then say it cannot communicate. Any help?
Mine does the same thing!
does it come with the oboII plug or is it sold separately
Yes it comes with all cables
Thought the 319 would do it - but nope. I think only the 619 will do it.
What does the AutoLink connect to in the mini?
OBD-II it's under left hand driver side. There is a little trap door to snap down to access it
Hello,
How do you reconnect the cable? I did purchase the Autolink. I have R56, 2008, Mini. Thank you for the video.
StarletteNyte Cain it comes on when you remove seats or disconnect while battery is still plugged in. Basically I moved seats out of car to clean
Hi Scouser Tech,
My seat was moved too far forward putting a baby car seat in the back. How do you remove the seat? I'm hoping if I remove it, put it back in place, that will fix the problem. And, thank you so much for your reply.