Add Factory Cruise Control 87-91 OBS Ford F150 F250 F350
ฝัง
- เผยแพร่เมื่อ 20 พ.ย. 2022
- How to add factor cruise control to you 1987-1991 OBS For truck. This project cost me about $200, and with this video it will be about a 1hour install for others.
Parts & Part numbers
Ford calls their cruise control “speed control”. So you may try searching these items with that phrase rather than “cruise control”.
Steering wheel pad
Cruise control vacuum dump valve
Vacuum canister
Horn relay- E5DB-13853-A3A
Cruise control harness - E9TB-AE-9A840
Dump valve pusher pad - E6TA-9C962-BA
Cruise control module - E9TZ-9D-843D
Cruise control servo - E5AF-9A827-AA
Follow me
/ dexter.ranch
/ dexterranch
/ dexterranch
Email me: dexterranch@yahoo.com
Thanks for the video it answers a lot of questions and makes it simple to work on my cruise now. It seems to be harder to find people that can answer questions about these older trucks. Good job.
I have been looking forever for this video. Keep all the great 87-91 videos coming!
This was great, and now I can test my system to find out why it is not working for me
Thank you……this is gonna help diagnose my non working cruise control…….
Great video. Thank you very much! ❤
Thank you so much for this. I wasn't able to find a good enough video on this to tackle this project but I believe I'll finally add cruise to my 1988 F150!
What a wonderful video!
High-quality, good info.
Thank you!
Thank you Sir.
What a great explanation. Much appreciate it.
Very well done! I will like to see one for these old trucks on how to troubleshoot them, wiring harness test and so on. 1991 F150, Mine stopped working, out of the blue and a good schematic will actually help.
Absolutely great pacing. Thought I knew all the obs tricks. Nice to learn some new ones
Thanks! didn’t get a chance to work on it- Rain 🌧️ and cold 🥶
your a great man! many many thanks, i just inherited a 1990 fordxlt 150 and is my first time operating a efi motor, so you got me thinkin in the right direction because ii'd probably be methodicaly thinkin of how this old truck runs without a damn carb 😆😂😉
I came here to help diagnose a speed control system, not install one, but there's a lot of good info here. Good work. 👍
Thank you!
Excellent information
Thank you!
Thanks for this
No problem. Thanks for watching!
I'll take the 1st comment and the 1st thumbs up😉🙂
Nice!
Great video! I have a 91 f250. I swapped the zf5 into my 1986 f150. Thinking the cruise control will come along as well.
I am doing this addition to my Manual 1991 F150, and I was wondering where the gray safety switch plug went. Is it a part of the harness, or does it plug in elsewhere? Thanks!
Great video, I'm planning on this swap too. I noticed that 90-91 trucks don't have the little grey 2-pin connector under the kick panel, but im not sure why, or if it matters?
Excellent 👍
Thank you!
@@dexterranch I made sure all the pieces of the puzzle are there and connected as you described. The cruise control is intermittent and mostly not turning on! any thoughts which component could be the culprit? the servo ?, the cut-off switch…
My gut says servo. I would start by thoroughly cleaning the male and female side of the connector that goes in the side of the servo. Also try to get a little dielectric grease in each pin. Make sure the horn is functioning properly. If it’s not it could be a grounding issue from the column to the frame. Hope this helps.
If you replace a Ford Factory 87-91 “Non Cruise Control” steering wheel on a same years factory Cruise Control steering column’ will a dash check light come on since “Cruise Control” isn’t hooked up anymore.
I have an 87 with the 5.0L gas engine. Has cruise control...but it ain't working. won't engage. I checked the fuses...all good. check the vacuum line going to the servo...lots of vacuum present. checked and adjusted the vacuum purge valve hooked to the brake pedal. what should I check next?
I have a question on 1987 ford 150 relays can I send you a Picture and the question, I am a novice with some experience but a bit stumped as to what this certain yellow connection relay is
Hay there you are I've been waiting for you to post again hope you have been well I'm sure you got some snow?
Hi Shaun! Yes we did get about 3 inches one day last week. Hope all is well with you also buddy!
@@dexterranch well things have been kinda crazy here, we had a fire a few weeks ago and lost are barn and pretty much everything in it, I was able to get all my cow out so we didn't loose any critters. Now we're fighting with insurance they don't want to pay out cause we had equipment in there for are lawn business so there trying to say it should have been covered by business insurance not homeowners. So it been real fun.
We went to are regional Dexter meeting in September I was thinking about you then.
Everything the same for EFI?
So in theory, I can add the factory cc from my '95 parts truck and slap it in my '88? Both are f250 5.8 4wd
92-96 is different stuff from 87-91.
Is someone a OSB collector? Seen one, now I see two?😁
Lol. Guilty. It is taking over my mind! Or maybe it’s just a phase 🤷🏻♂️. Either way the answer is yes. Hope all is well with you and yours!
@@dexterranch Next thing you will have 5........My brother tells me a collection is 10? I know how it is, I got 67-72 GM truck fever.