Got my first dro , sino, the Chinese manuel sucks and I'm not a wizard but not stupid either so I'll be watching your videos over and over. I appreciate the time you've taken and you explain very clearly. THANKS FROM OHIO.
I agree 100%. The greater confidence I have in the accuracy of my DRO the more I will use it. I've used blocks to calibrate mine but do not have the confidence in myself that I am as accurate as I should be.
Good point, I was able to borrow some stick mics, and over 600 mm the DRO was out by 1.2 mm on my newly fitted linear scales, there is a scaling parameter to correct this. I think there was also an incremental scaling parameter, ref every 50mm or so.
I know my dro is out as I've checked it and tried to recalibrate it, but using the manual it refuses to go into the recalibration mode. I've followed it about ten times at different times and still the same result. In the same way my dro will not allow you to reset a zero when in imperial. I have to switch into metric reset to the dimension I want ( let's say diameter of the work) then go back into imperial if I'm working that way. It's bloody annoying. I'm seriously thinking of replacing the DRO unit for a better one despite the extra cost as long as it will work with the glass scales, even if I have to rewire the plug to get it to work.
I watched about half of this, then went back to watch This Old Tony's video on DRO's. Came back here and I have to say a much clearer explanation of whats going on. I look forward to seeing you covering off more on DRO's as I think that there is far more you can do with them than people suspect. I'm in the happy, or unfortunate position of of having 3 machines with DRO's on them, all 3 being different manufacturers. I need to get my head around the old Heidenhain system on my new to me mill, still to be set in position.
Fantastic layman's explanation of ABS and INC, another good use if you have both sets of measurements on a drawing is to cross check between both. If your working using INC, before say drilling a hole is to do a quick check in ABS to make sure the measurements coincide.
Excellent video Jon. Very well presented. My DRO came with a very thin instruction book, most of which I didn't understand. I learned mostly from videos like yours. Was a while before I understood ASB INC. I also use the DRO to find centres and PCD. More videos on the DRO would be very useful Jon. Cheers Nobby
Great video Jon, I’d like to see more videos on this subject if possible. I’ve been considering putting dro equipment on my machines and some basic knowledge on them will be invaluable
Hi Jon. Extremely well explained and simplified for the complete DRO novice to understand, or someone who has never written or read a working drawing before. Reminds me of a box where only the internal dimension were given,lol. Cheers Tony
I left a similar comment with Joe Pie: please get yourself a lav mic. they don't cost much, but they will make your voice sound so much better than the in-camera mic across the room
Absolutely wonderful, as an novice, I have never understood it that way, thank you for this. I have a Chinese (SINO) on my mill, that I can't understand the bolt hole circle functioning and setup. Can't wait for a video about that ! Thank you for this !!!
Great video and very helpful. I've used a few of the features on my DRO such as the hole circle and sub-datum points but it was a bit of a struggle figuring them out. The manuals are so poor. Looking forward to more.
Well explained Jon . Only my big mill has a dro at this stage . Yes , some drawings can get overloaded with construction lines & dimensions esp as we were never allowed to dimension inside a part on a drawing . A lot has seemed to change on drawings since the standards we were taught in the late 70's & early 80's . 👍
Very helpful video Jon. I would love to see more DRO function videos. Those of us who own import DRO’s know the manuals that come with them are not clearly worded on how or when to use the many functions. SDM for example, is one mine has but I have no idea how to use it. More videos on this subject would go a long way to help get full use out of the many functions available.
Hi Jon. I must admit i have never used the inc function. Must get my head round it. I have used the circle function quite a lot. What would we do without the DRO. Imagine how hard & long winded it was for engineers back in Dick's days with play in the machine. Great video. Steve.
Hi Steve, thanks for the comment. I learnt without DRO so it never leaves you. I feel sorry for those who have never not used a DRO, as when they break down, there's a steep learning curve ahead. Cheers, Jon
Great video. I’ve never understood absolute vs. incremental. I have to admit I’m still a little fuzzy on the how and why, but I’ll figure it out with your help. I’ll watch the video until I get it. Thanks again.
I hope my Sammie was paying close attention and making notes, because with chemo brain fog, I will have to come back when the fog has left the pond 😁. Great demo Jon, and clear as a bell. I sure miss being out in my shop, but hopefully will be soon, Besr
Excellent synopsis on dimensions, im guessing many hobbyists never have the chance to view or work with professional engineering drawings, surprisingly, each detail draughtsperson can be quite different as you no doubt know. An art form when done well. Thanks for sharing.
Hi John, 100%. Those that have not quite grasped proper use of dotted lines have caught me with my pants down before....... Long story lol. Cheers, Jon
@@jonsworkshop Yep, been confused by dotted lines, and drawings that were in both 1st hand and 3rd hand projection, maybe an idea for a video?, I still have to think when looking at drawings now, used to be automatic, even though reading title block beforehand for view, scale, dimensions etc. A great help now is most 2D GA's and detail drawings are generated from 3D models, so there's a small ortho model shown, or several, plus sections on complex or high end components. Best regards John
Jon this is excellent subject material. I get confused when using my DRO also. Therefore, I try to keep it in ABS mode. I would like to use my Inc more than I do. There is a function where you can preset the dimensions using Inc and just dial to ZERO on each dimension. I would love to see more about Inc and any other functions of the DRO. Bolt circle function finding different angles etc. I am all about learning new things so you can bet I will be here waiting for the next videos. Thanks for bringing us along
Thank you. I get it now. Probably not use it as explained just yet. I use the 2 functions as if it was 2 DROs at the same time. So can pick up a different datum for two operations on the same piece. Ang on - is that what you just explained......
Great Jon! You did it for us! Thank you so much, but I challenge you to read my dro instructions and even understand anything as it's in Chinglish! You've made me understand the differences between the two styles of measurement. I did (and taught in fact ) Technical drawing to 'A' level standard but absolute measurements were the norm back in the days of laying parts out on the surface table using a vernier height gauge. Long before electronic measurements were even thought of lol And yes I would love to see videos on different functions especially the hole circle pattern and SDM. Ps the name samrodian is all one word derived from my three Christian names all rolled into one and pronounced as you would if taking to someone. Me lol
Thanks Jon, good instructional video. One problem I have with the Sino DRO on my mill is setting up angles using the DRO, eg setting a vice or fixture to a precise angle using it. The instruction books Chinglish description of how to do it is driving me insane.
Thanks for a great explanation of that DRO function. I have a much better grasp on how they co-relate now. You are an awesome teacher, you can "dumb down" stuff that's technical for us mere mortals!...LOL. Cheers from Canada
THANK YOU, yes I know I'm yelling but I appreciate what you just explained here. If you get a chance I would really like to see how multiple Datum points (SDM) would be setup and used. I installed a DRO on my mill a few months back, I'm a home/hobby machinist if you could call me that and this helps a lot. I am also wanting to learn the hole pattern function and I imagine different DRO's may use a different way of inputting to get the same results but I'm not sure maybe they all use the same and try to keep it universal.
Well Jon, That made... sorry what where you on about I was licking my windows n not paying attention! Actually what I meant was, I went to the workshop and made all the parts shown in your tutorial HONEST 😁 As always Dude stay safe n well. TFS, GB :)
I thought Pattern Maker's new a thing or two but I gaining more respect for Machines ( i through they got on a lathe turned the dials ) Kit from down under
Great video Jon, now I understand the difference between ABS and INC👍 are you able to tell me how to input a diameter on the lathe DRO so the part diameter decreases as I remove Meterial? Thanks John
Thanks John, would you believe it, I have never used a lathe with a DRO lol. My guess is, turn a Dia, measure it, go to calculator function and type in what you measured, then press the X0 button. Don't forget to press the calculator button again after to return to ABS mode. Cheers, Jon
Interesting video Jon, it will help many, won't help me as i only have a poormans dro, with one function, absolute🤣🤣🤣🤣, but having said that, being brought up in an era with no dro's i normally stick to old school dials, which suffices the work i do, I doubt if i will ever spend to have a proper dro, unless one drops off a christmas tree🤣🤣🤣🤣 Thanks for sharing see you next time👍👍👍👍👍👍 regards Kev
Hi Kev, thanks for the comment. Yup, I learnt the hard way too, I sometimes still refer to the dials as a sanity check even though I have the DRO. Cheers, Jon
with incremental you would need to be realy carefull when zeroing the dro at least if its done the way you shown on the whiteboard realy interesting way of showing how it works , havent seen it done that way yet even though there are a few explanation videos about the use of the different options on a dro , having a set of these on a single channel would be helpfull having the different options explaned (the way you did with the piece of cardboard) in seperate videos would save me some time scrolling through a video explaning everything halfway without showing the drawing with the refferences on the workpiece (that realy helps) the most clear explanation ive seen before yours is from blondihacks
I wish I had time to watch this but 23 minutes is just too long. I would love to see a vid that explained that in 5 mins. Its probably a brilliant vid.
Got my first dro , sino, the Chinese manuel sucks and I'm not a wizard but not stupid either so I'll be watching your videos over and over. I appreciate the time you've taken and you explain very clearly. THANKS FROM OHIO.
Thanks Mike
Good instruction Jon, it may be worth doing a follow-up on calibrating these DRO,s using gauge blocks
I agree 100%. The greater confidence I have in the accuracy of my DRO the more I will use it. I've used blocks to calibrate mine but do not have the confidence in myself that I am as accurate as I should be.
Good point, I was able to borrow some stick mics, and over 600 mm the DRO was out by 1.2 mm on my newly fitted linear scales, there is a scaling parameter to correct this. I think there was also an incremental scaling parameter, ref every 50mm or so.
Hi, thanks for the comment. In the memory bank for future tips videos.
I know my dro is out as I've checked it and tried to recalibrate it, but using the manual it refuses to go into the recalibration mode. I've followed it about ten times at different times and still the same result. In the same way my dro will not allow you to reset a zero when in imperial. I have to switch into metric reset to the dimension I want ( let's say diameter of the work) then go back into imperial if I'm working that way. It's bloody annoying. I'm seriously thinking of replacing the DRO unit for a better one despite the extra cost as long as it will work with the glass scales, even if I have to rewire the plug to get it to work.
Thanks Jon, just come across this having finally completed my DRO installation on my lathe. Very clearly explained!
👍
Great instructional video Jon
Thanks for taking the ( considerable) time to script, shoot, and edit the vid.
Regards
Robert
No problem Robert, glad it was useful.
Very fine explanation. Thank you!
I watched about half of this, then went back to watch This Old Tony's video on DRO's. Came back here and I have to say a much clearer explanation of whats going on. I look forward to seeing you covering off more on DRO's as I think that there is far more you can do with them than people suspect.
I'm in the happy, or unfortunate position of of having 3 machines with DRO's on them, all 3 being different manufacturers. I need to get my head around the old Heidenhain system on my new to me mill, still to be set in position.
Thanks Bill, lol, I would take TOT's revenue just for that one video, I could retire and make loads more instructional films lol. Cheers, Jon
Hi Jon. I have learned more watching you than hours in the manual. Many thanks Richard
Thanks Richard
SDM, Yes please, and other functions less used.
This video has helped me great, many thanks. 👍😎
You got it!
Morning Jon. Thank you for the clear overview of DRO ABS and INC functions. Please continue to make videos which show other useful DRO functions. 👏👏👍😎
Will do Andrew. Thank you.
Best explanation I've seen by a country mile! Thank you Jon
Glad it was helpful!
Fantastic layman's explanation of ABS and INC, another good use if you have both sets of measurements on a drawing is to cross check between both. If your working using INC, before say drilling a hole is to do a quick check in ABS to make sure the measurements coincide.
Excellent as ever Jon...I do hope you have apprentices around you in your workplace because your knowledge, patience and delivery is awesome.
Hi Philip, yes, I do have a few in my team, and I do try when I get time to impart some wisdom (if that's what it is) 😂😂😂
Excellent video Jon. Very well presented. My DRO came with a very thin instruction book, most of which I didn't understand. I learned mostly from videos like yours. Was a while before I understood ASB INC. I also use the DRO to find centres and PCD. More videos on the DRO would be very useful Jon. Cheers Nobby
Thanks Nobby, more to come (with theory😂😂😂)
Hell yes I'd like more on the functions available with a DRO. I've only used ABS and the hole circle functions on mine.
More to come Kenneth
Great video Jon, I’d like to see more videos on this subject if possible. I’ve been considering putting dro equipment on my machines and some basic knowledge on them will be invaluable
Will do Mark, you won't regret it
good video jon..thanks for your time
Hi Jon. Extremely well explained and simplified for the complete DRO novice to understand, or someone who has never written or read a working drawing before. Reminds me of a box where only the internal dimension were given,lol. Cheers Tony
Thanks Tony, much appreciated mate
Thanks Jon Very helpful - more of the same please
More to come!
Great video Jon more videos on DRO,s Please
Thanks Adrian
I left a similar comment with Joe Pie: please get yourself a lav mic. they don't cost much, but they will make your voice sound so much better than the in-camera mic across the room
Thanks for the comment and feedback, I may get one in the future. Cheers, Jon
Absolutely wonderful, as an novice, I have never understood it that way, thank you for this. I have a Chinese (SINO) on my mill, that I can't understand the bolt hole circle functioning and setup. Can't wait for a video about that ! Thank you for this !!!
Glad it was helpful, more to come 😊
Great video and very helpful. I've used a few of the features on my DRO such as the hole circle and sub-datum points but it was a bit of a struggle figuring them out. The manuals are so poor. Looking forward to more.
Glad it was helpful, more to come 😊
Brilliant Jon. Thank you.
My pleasure!
Well explained Jon . Only my big mill has a dro at this stage . Yes , some drawings can get overloaded with construction lines & dimensions esp as we were never allowed to dimension inside a part on a drawing . A lot has seemed to change on drawings since the standards we were taught in the late 70's & early 80's . 👍
Bang on Max, I learnt on a proper drawing board with a pencil, would struggle these days. Cheers, Jon
I never used a DRO, but it all makes perfect sense. Very well axplaned, Jon.
Thanks Rusti. 👍👍
Thanks Jon. Helpful indeed.
My pleasure Tom
That was fantastic
Well done, that was a great explanation! Looking forward to a video on Sub Datum Memory.
Coming soon!
Very helpful video Jon. I would love to see more DRO function videos. Those of us who own import DRO’s know the manuals that come with them are not clearly worded on how or when to use the many functions. SDM for example, is one mine has but I have no idea how to use it. More videos on this subject would go a long way to help get full use out of the many functions available.
Hi Darrell, thanks for the comment and feedback. More to come.
Hi Jon, nicely done as always mate, hope you're keeping well, have a great one 👍
Thanks Ralfy, you keep on that journey you are on mate, brilliant job
Hi Jon, good stuff, I’ve never used a dro but it was still very interesting for me, also well explained, thank you.
Glad you enjoyed it
Thank you for braking that down . Very helpful. hope you will do more on the fucshouns on the DRO.
More to come Joseph
Thanks for sharing 👍
Hi Jon. I must admit i have never used the inc function. Must get my head round it. I have used the circle function quite a lot. What would we do without the DRO. Imagine how hard & long winded it was for engineers back in Dick's days with play in the machine. Great video.
Steve.
Hi Steve, thanks for the comment. I learnt without DRO so it never leaves you. I feel sorry for those who have never not used a DRO, as when they break down, there's a steep learning curve ahead. Cheers, Jon
Thanks Jon 👍 A worthwhile topic.
Thanks Dudley
Great video. I’ve never understood absolute vs. incremental. I have to admit I’m still a little fuzzy on the how and why, but I’ll figure it out with your help. I’ll watch the video until I get it. Thanks again.
Thanks for the comment and feedback Roy, glad it was helpful. Cheers, Jon
More videos on DRO functions would be great 👍🏼
Will do!
I hope my Sammie was paying close attention and making notes, because with chemo brain fog, I will have to come back when the fog has left the pond 😁. Great demo Jon, and clear as a bell. I sure miss being out in my shop, but hopefully will be soon, Besr
Sam here lol yes I was! See my reply to Jon !
fantastic, thanks
!
Enjoyed this video well done,, I would like to hear more about SDM function and how it’s used!
Coming soon Bill
Good one Jon ! enjoyed
ATB...Cheers
Very informative, more please
Excellent synopsis on dimensions, im guessing many hobbyists never have the chance to view or work with professional engineering drawings, surprisingly, each detail draughtsperson can be quite different as you no doubt know. An art form when done well.
Thanks for sharing.
Hi John, 100%. Those that have not quite grasped proper use of dotted lines have caught me with my pants down before....... Long story lol. Cheers, Jon
@@jonsworkshop Yep, been confused by dotted lines, and drawings that were in both 1st hand and 3rd hand projection, maybe an idea for a video?, I still have to think when looking at drawings now, used to be automatic, even though reading title block beforehand for view, scale, dimensions etc.
A great help now is most 2D GA's and detail drawings are generated from 3D models, so there's a small ortho model shown, or several, plus sections on complex or high end components.
Best regards John
Hi john love your videos, could you do a video on PCD function.
Thanks Paul, coming soon
Jon this is excellent subject material. I get confused when using my DRO also. Therefore, I try to keep it in ABS mode. I would like to use my Inc more than I do. There is a function where you can preset the dimensions using Inc and just dial to ZERO on each dimension. I would love to see more about Inc and any other functions of the DRO. Bolt circle function finding different angles etc. I am all about learning new things so you can bet I will be here waiting for the next videos. Thanks for bringing us along
Thanks Terry, great feedback. More to come 😊
Thank you. I get it now. Probably not use it as explained just yet. I use the 2 functions as if it was 2 DROs at the same time. So can pick up a different datum for two operations on the same piece. Ang on - is that what you just explained......
Hi Kevin, thanks for the comment. Yep, pretty much lol.
Great Jon! You did it for us! Thank you so much, but I challenge you to read my dro instructions and even understand anything as it's in Chinglish! You've made me understand the differences between the two styles of measurement. I did (and taught in fact ) Technical drawing to 'A' level standard but absolute measurements were the norm back in the days of laying parts out on the surface table using a vernier height gauge. Long before electronic measurements were even thought of lol
And yes I would love to see videos on different functions especially the hole circle pattern and SDM.
Ps the name samrodian is all one word derived from my three Christian names all rolled into one and pronounced as you would if taking to someone. Me lol
Hi Sam (that helps for future..... Less typing), glad you enjoyed it and found it useful. More to come. 😊
Great explanation Jon. I really enjoyed it.
Thanks Carl, appreciated
@@jonsworkshop Pleasure.
Thanks Jon, good instructional video. One problem I have with the Sino DRO on my mill is setting up angles using the DRO, eg setting a vice or fixture to a precise angle using it. The instruction books Chinglish description of how to do it is driving me insane.
Amen on the Chinglish
Thanks John, more to come, seems to be a popular request 😊
Thanks Jon, look foward to it.@@jonsworkshop
Thanks for a great explanation of that DRO function. I have a much better grasp on how they co-relate now. You are an awesome teacher, you can "dumb down" stuff that's technical for us mere mortals!...LOL.
Cheers from Canada
Hi bhein67, thanks for the comment and feedback. More to come 😊
THANK YOU, yes I know I'm yelling but I appreciate what you just explained here. If you get a chance I would really like to see how multiple Datum points (SDM) would be setup and used. I installed a DRO on my mill a few months back, I'm a home/hobby machinist if you could call me that and this helps a lot. I am also wanting to learn the hole pattern function and I imagine different DRO's may use a different way of inputting to get the same results but I'm not sure maybe they all use the same and try to keep it universal.
Thanks for the comment and feedback. No problem, more on the way 😊
Well Jon, That made... sorry what where you on about I was licking my windows n not paying attention! Actually what I meant was, I went to the workshop and made all the parts shown in your tutorial HONEST 😁 As always Dude stay safe n well. TFS, GB :)
Lol Graeme 🤣🤣🤣🤣.
I thought Pattern Maker's new a thing or two but I gaining more respect for Machines ( i through they got on a lathe turned the dials )
Kit from down under
Thanks Kit
angle function would be great, I've read the instructions numerous times and i'm still lost😁
Noted Paul, on the to do list
Great video Jon, now I understand the difference between ABS and INC👍 are you able to tell me how to input a diameter on the lathe DRO so the part diameter decreases as I remove Meterial? Thanks John
Thanks John, would you believe it, I have never used a lathe with a DRO lol. My guess is, turn a Dia, measure it, go to calculator function and type in what you measured, then press the X0 button. Don't forget to press the calculator button again after to return to ABS mode. Cheers, Jon
@@jonsworkshop Thanks Jon I’ll give it a go.
Thanks dude.. helpful.. been struggling too...
Good job Jon not easy to get that across even to people who use dros every day 👍👍👍👍
Thanks Steve, much appreciated.
Interesting video Jon, it will help many,
won't help me as i only have a poormans dro, with one function, absolute🤣🤣🤣🤣, but having said that, being brought up in an era with no dro's i normally stick to old school dials, which suffices the work i do, I doubt if i will ever spend to have a proper dro, unless one drops off a christmas tree🤣🤣🤣🤣
Thanks for sharing see you next time👍👍👍👍👍👍
regards
Kev
Hi Kev, thanks for the comment. Yup, I learnt the hard way too, I sometimes still refer to the dials as a sanity check even though I have the DRO. Cheers, Jon
basically you can use incrementals inside the absolute or along side :)
more dro videos please
Will do
with incremental you would need to be realy carefull when zeroing the dro at least if its done the way you shown on the whiteboard
realy interesting way of showing how it works , havent seen it done that way yet
even though there are a few explanation videos about the use of the different options on a dro , having a set of these on a single channel would be helpfull
having the different options explaned (the way you did with the piece of cardboard) in seperate videos would save me some time scrolling through a video explaning everything halfway without showing the drawing with the refferences on the workpiece (that realy helps)
the most clear explanation ive seen before yours is from blondihacks
Thanks Watahyahknow, more to come 😊
Well explained, thank you. I’d send you a slab of Guinness but I don’t have your address. Hey ho, not to worry. Its the thought that counts. 🤣
Lol, thanks Ricky😂
Kind of sounds like a Chinese menu:
I'll have one from datum A
and one from datum B
and three from datum C
Lol🤣🤣🤣
Hi mate it's trevor that is a good video mate I didn't know that I yous abs Inc but not that way but I no now 😅😅😅
Hi Trev, thanks for the comment and feedback, much appreciated mate. Look after your pal for me. Cheers, Jon
We are looking after him I got him back in the shed today told him that I needed a hand ✋️ that cheered him up a bit 😀 😉 😄
I wish I had time to watch this but 23 minutes is just too long. I would love to see a vid that explained that in 5 mins. Its probably a brilliant vid.