Thank you very much for this video. It literally saved me from spending almost $700 at the mechanic shop. I loved how you should every nook and cranny. Thanks again
Thank you so much. I went to fix this on my own because I have taken the door panel off many times for stereo work-- however, I could not figure out how to remove the lock and handle to see the issue. Your video helped me identify the T30 fastener on the rim of the door and also how to remove the yellow clasp that holds the locking lever in place. Life saver. I agree, putting the glass window rails back onto the inner panel is a pain. I found suction cup handles from harbor freight made it so much easier. I was able to adjust the glass to the right position and line up the rakes with the panel. I used a piece of string at first to pull the rails flush with the panel because I was having a hard time getting the screws to "catch" the threading on the rails. Once the rails were pulled against the panel I fasted them and it was smooth soaking from there thank you again!
Thanks, that was exactly my problem on our 2013 Rogue. One tip to get access to the inside handle, roll the window down half way, remove covers to expose big holes so you can detach the glass and lift out. Then only remove the black 10mm bolts to remove the entire power window assembly. Piece of cake! Do NOT loosen the silver 10mm bolts!
This video is super helpful thank you for making it. I think you're having the same problem i am. The cable is a metal stranded cable so it's wound. I'm pretty sure my cable has stretched itself overtime. So i had to replace the entire cable to the Lock actuator and it seemed to fix it. I think they used cheap wound cables that stretch over time.
Thanks for the video! You really helped me out of a bind. Customer needed their car back to soon as possible. Couple things I did different that might help others.First thing I did was tape the window up so it doesn’t come down when you pull the regulator panel away from the door. Second thing I did was instead of using a screw to make up for the gap I used just enough clear silicone to fill in the gap to stop the ball end of the cable from popping out. Making sure the silicone doesn’t interfere with the ball end of the cable. I just subscribed to your channel. Thanks again!
Great video helped me out with my Infiniti QX50 that had the same problem and a very similar setup on the inside. Saved me a trip to the shop! Thank you!
This was great, I have a good customer and this has happened twice… first time I did it with the window down I have no idea how I did it… noticed you did it with the window up, that’s key, much more room.
Thanks for the guide helped me out a ton, the way i combated the ball falling out was to pinch the circle that it sits inside, the cable can’t slip out and the mechanism works flawlessly
Thanks for this, looked for other instructions but could find none. One thing I wish you would have shown was how to get the damn thing apart to get to the cable. Getting that lock out drove me mad until I saw where I could snap that yellow clip off the rod down below, allowing the lock to rotate out. I took some pics of how I fixed it. I actually made a little "shield" to hold it in. Need to file a patent now and get paid for my marathon fix on the wifes ride. Cheers.
I just did this repair (new drivers door) handle on 2011 Rogue with keyless entry yesterday. Without viewing videos like this one, the job would have been much more difficult. Hint, tape the windows in the full up position before you remove regulator panel. The holes lined up and I drew it together with longer 8mm bolts (not supplied) and one by one replaced with factory 8mm bolts. The whole job, about 1.5 hours of twisting and swearing!
this door still opened. see if you can remove or even slightly move the door panel from the inside out of your way and try to pull that cable that opens the door.
Worked on my brother-in-laws 2011 Rouge and found that removing the window glass allows you to remove the black panel AND the window rails as a single unit. This is much easier than trying to re-align the rails to put those silver bolts back in. There are only 2 bolts holding window in, and it's an easy remove and return.
Thank u sir for this video and was going to bring in my vehicle n mechanic told me i need to dropped it off cause he stated something broken inside n need to order some parts lol oh well ill just do it myself.You be safe out there.Keep doing what u do best.
The dealership quoted me 100 bucks to fix it. After fixing it myself, I almost would pay them to do it. This is a common problem because of bad design. They should fix it for free.
@@Ed-cs6kw $100? where are you at? that is great price. Amen-it is a poor design and they should indeed...common Nissan issue. We should get like a 25K signatures on change.org, lol. One guy said we should report it as safety issue, lol. (NHTSA). The CVT is another big one for Nissan.
@@grymbathym635 Yes it worked, its basically the same - the only difference was i removed the glass, it comes out at an angle through the window frame, after you loosen the two screws holding the glass to the elevator mechanism.
I did this before in 2019. Lasted almost 2 yrs. It hapened again few months ago during freezing weather. I dont recall totally taking the lock out, but had it disconnected in there (from the rod)...I had a heck of time with the window regulator attachments/plastic and it looked bent from factory...(i actually had it all out of the door for some reason) It seems like this is a problem with 'many' Nissans (incl Sentra/Altima). I found a listing for a recall circa 2010 for the Rogues regarding the latch popping out, but i have been to dealers a handful of times during ownership and asked on recalls and nothing was ever mentioned about the latch, smh. The screw was a great idea! I am finding it hard to bring myself back to go thru this again. Plus my tools are across the country. Anyone in TX that I can pay $60 to do this for me?? LOL. Due to this kind of fun as well as the CVT, the only Nissan i would buy again would be older Xterra.
my 2012 just did this for the first time. Nissan used to never have issues like this. This is the 3rd thing thats happened to mine since I bought it new in 2012. IDK I dont see the quality I used to and my Nissan Frontier is the same way.
Agree, Renault,etc. bought Nissan I think and in decline ever since. On many top car pick lists, Nissan is falling. Now late model Hyundai/Kia are ahead. The CVTs are a huge issue/risk as your mileage climbs.
u can go thru what this clip is showing - I would try a fix it by trying hot gluing myself - the plastic that is for the cable and ball is worn is the true issue - this is why the ball is coming out - this needs to be a recall - this is a problem with the roque - more and more owners are running into this issue-- another issue Nissan has with the Roque handles that crack - there is a flaw in the manufacturing design of the handles -
I watched you do the repair video pretty good but can you help me if you are out there I am trying to open my door so I can take the panel off my handle is broken it is doing exactly what you were saying it is doing please help me how do I open my door
I havent had that issue, the door would still open for me but I think your best bet is to get yourself a lockout kit or another name for it is a slim jim for car door. In my video you can see where that lock unlock rod is so you should be able to rich it with your window open with that tool to get your door open, you can get that tool online or your local automotive store. Good luck.
Great video and innovative fix. I'm by no means we'll versed mechanics and decided to take on the task of fixing the door handle on my girlfriends Nissan Rogue. I got it done however I'm having a stressful time trying to get the lock to line up with that screw on the side of the door any idea why? The screw is hitting just before the hole on the locking mechanism.
Recently purchased a used 2020 nissan rogue and it started doung this after a month bru and now im fixing it myself cuz the dealership i bought it from wanted to charge me wayyyy too much to fix it
is it loose? theres a bolt in the door on the side where the latch is, if u already took that out then just move it around, it came out for me so it should come out for u.
Same my 2010 rogue drivers side has been hell. The exterior handle broke during inspection. Fixed it....then the window wouldnt roll up or down....fixed that...now you cant open the door from the inside and it's the front driverside door
Hi, have same problem today, cannot open door from handle outside but from inside can open with nissan navara np300 2017 year this, be same problem to repair?
the whole handle assembly with the lock cylinder is held on with one torqs bolt (T30) on the side of the door or door jam, remove that bolt and the handle should come out, then the lock cylinder. Dont forget about the yellow clip.
Thank you very much!! Because I was trying to remove that bolt and keeps turning and turning. So, definitely I need to remove both door panels, I guess. The only problem that I need to fix is the door handle that has broken and of course we can’t open the door. But once again, thanks a lot, I’ll try the yellow clip this time.
My door opened from the inside, if yours doesnt then you have more issues. This isnt my car so I couldnt tell ya if theres something you can remove from the door panel and try to reach in to pull that cable.
Hey congratulations man. 770 subs. And 30.000 plus views on this video. Great job 👍👍👍👍👍. I think you be the next Scotty Kilmer 😁😁😁😁😁. It’s just that your videos are much better than his.
Awesome info! I’m registered with Nissan to receive all factory recalls on my model (2013) and have no info on that. I’ll be visiting my local dealer this week😬😬😬
@@amederward7081 ya exactly. ONLY Nissan would have a recall that expires. I had many trips to dealers before 2014 and never a peep about this recall. Now mine is unlatched/broken again. Never another Nissan, smh.
I hope I never have to do this to my 2016 or 2017 rogues. What a pain. I also hope the wife's Leaf is simpler because that one I do have to do. the chrome piece loses a tab that holds it on. What an annoying crap design.
bro what part of the country are you in I need to pay you to come and fix my wives it looks like a pain in the ass and hers is doing it now it's been doing it for a week Good tutorial though
NEVER EVER BUY A NISSAN AGAIN!! ive replaced so many mechanical parts of my 2014 nissan select. Now the door handle, and no air bags now because it cost $1000. + 200 i pd already for diagnostic 😡😡 so Hate Nissan, so so frustrated!!
![ละลาย (LALALYE) - DAOU PITTAYA ต้าห์อู๋ พิทยา [OFFICIAL MV]](http://i.ytimg.com/vi/wo6r9TgausI/mqdefault.jpg)
Thank you very much for this video. It literally saved me from spending almost $700 at the mechanic shop. I loved how you should every nook and cranny. Thanks again
Except the whole taking it apart aspect. 😅😂😂
Thank you so much. I went to fix this on my own because I have taken the door panel off many times for stereo work-- however, I could not figure out how to remove the lock and handle to see the issue. Your video helped me identify the T30 fastener on the rim of the door and also how to remove the yellow clasp that holds the locking lever in place. Life saver. I agree, putting the glass window rails back onto the inner panel is a pain. I found suction cup handles from harbor freight made it so much easier. I was able to adjust the glass to the right position and line up the rakes with the panel. I used a piece of string at first to pull the rails flush with the panel because I was having a hard time getting the screws to "catch" the threading on the rails. Once the rails were pulled against the panel I fasted them and it was smooth soaking from there thank you again!
Thanks, that was exactly my problem on our 2013 Rogue. One tip to get access to the inside handle, roll the window down half way, remove covers to expose big holes so you can detach the glass and lift out. Then only remove the black 10mm bolts to remove the entire power window assembly. Piece of cake! Do NOT loosen the silver 10mm bolts!
Great tip, hopefully people will notice your comment.
th-cam.com/video/MQAz5jAkI98/w-d-xo.html minute 3
This video is super helpful thank you for making it. I think you're having the same problem i am. The cable is a metal stranded cable so it's wound. I'm pretty sure my cable has stretched itself overtime. So i had to replace the entire cable to the Lock actuator and it seemed to fix it. I think they used cheap wound cables that stretch over time.
This seems a good option. Thanks for the tip.
Thanks for the video! You really helped me out of a bind. Customer needed their car back to soon as possible. Couple things I did different that might help others.First thing I did was tape the window up so it doesn’t come down when you pull the regulator panel away from the door. Second thing I did was instead of using a screw to make up for the gap I used just enough clear silicone to fill in the gap to stop the ball end of the cable from popping out. Making sure the silicone doesn’t interfere with the ball end of the cable. I just subscribed to your channel. Thanks again!
how did you keep the silicone from interfering...just filling near it and letting dry first? Such a poor latch design.
Great video helped me out with my Infiniti QX50 that had the same problem and a very similar setup on the inside. Saved me a trip to the shop! Thank you!
This was great, I have a good customer and this has happened twice… first time I did it with the window down I have no idea how I did it… noticed you did it with the window up, that’s key, much more room.
Thanks for the guide helped me out a ton, the way i combated the ball falling out was to pinch the circle that it sits inside, the cable can’t slip out and the mechanism works flawlessly
Thanks for this, looked for other instructions but could find none. One thing I wish you would have shown was how to get the damn thing apart to get to the cable. Getting that lock out drove me mad until I saw where I could snap that yellow clip off the rod down below, allowing the lock to rotate out. I took some pics of how I fixed it. I actually made a little "shield" to hold it in. Need to file a patent now and get paid for my marathon fix on the wifes ride. Cheers.
I just did this repair (new drivers door) handle on 2011 Rogue with keyless entry yesterday. Without viewing videos like this one, the job would have been much more difficult. Hint, tape the windows in the full up position before you remove regulator panel. The holes lined up and I drew it together with longer 8mm bolts (not supplied) and one by one replaced with factory 8mm bolts. The whole job, about 1.5 hours of twisting and swearing!
thanks for showing how much frustration I'm going to run into! now how to actually get the door open before fixing!
this door still opened. see if you can remove or even slightly move the door panel from the inside out of your way and try to pull that cable that opens the door.
Hey bro just want to say thanks. It's all good to use cardboard or anything handy. My Rogue was doing the same thing again thanks and take care.
Thanx for sharing! Now I know how much of a pain in the A this is gonna be to fix...
yap, even the second time wasnt that easy, good luck
Worked on my brother-in-laws 2011 Rouge and found that removing the window glass allows you to remove the black panel AND the window rails as a single unit. This is much easier than trying to re-align the rails to put those silver bolts back in. There are only 2 bolts holding window in, and it's an easy remove and return.
thanks, did you take any pics? have steps to do this?
Thank you soooo much for commenting on that! Doing it by removing the window glass was really easy!! Much appreciated.
Thank u sir for this video and was going to bring in my vehicle n mechanic told me i need to dropped it off cause he stated something broken inside n need to order some parts lol oh well ill just do it myself.You be safe out there.Keep doing what u do best.
The dealership quoted me 100 bucks to fix it. After fixing it myself, I almost would pay them to do it. This is a common problem because of bad design. They should fix it for free.
there was a recall on it but it ended a few years back.
@@cruizinmax4017 ya, I saw it too, how can a recall end? Nissan never told me.
@@Ed-cs6kw $100? where are you at? that is great price. Amen-it is a poor design and they should indeed...common Nissan issue. We should get like a 25K signatures on change.org, lol. One guy said we should report it as safety issue, lol. (NHTSA). The CVT is another big one for Nissan.
Thanks for sharing. Helped me replace my door handle.
Having the same issue with my Nissan X - Trail - will try your fix. Thanks for the video!
Did it work?
@@grymbathym635 Yes it worked, its basically the same - the only difference was i removed the glass, it comes out at an angle through the window frame, after you loosen the two screws holding the glass to the elevator mechanism.
I did this before in 2019. Lasted almost 2 yrs. It hapened again few months ago during freezing weather. I dont recall totally taking the lock out, but had it disconnected in there (from the rod)...I had a heck of time with the window regulator attachments/plastic and it looked bent from factory...(i actually had it all out of the door for some reason) It seems like this is a problem with 'many' Nissans (incl Sentra/Altima). I found a listing for a recall circa 2010 for the Rogues regarding the latch popping out, but i have been to dealers a handful of times during ownership and asked on recalls and nothing was ever mentioned about the latch, smh. The screw was a great idea! I am finding it hard to bring myself back to go thru this again. Plus my tools are across the country. Anyone in TX that I can pay $60 to do this for me?? LOL. Due to this kind of fun as well as the CVT, the only Nissan i would buy again would be older Xterra.
my 2012 just did this for the first time. Nissan used to never have issues like this. This is the 3rd thing thats happened to mine since I bought it new in 2012. IDK I dont see the quality I used to and my Nissan Frontier is the same way.
Ever since Nissan merged with Renault, quality has been going downhill.
Agree, Renault,etc. bought Nissan I think and in decline ever since. On many top car pick lists, Nissan is falling. Now late model Hyundai/Kia are ahead. The CVTs are a huge issue/risk as your mileage climbs.
This helped out a lot, thanks for uploading. 👍
u can go thru what this clip is showing - I would try a fix it by trying hot gluing myself - the plastic that is for the cable and ball is worn is the true issue - this is why the ball is coming out - this needs to be a recall - this is a problem with the roque - more and more owners are running into this issue-- another issue Nissan has with the Roque handles that crack - there is a flaw in the manufacturing design of the handles -
this used to be a recall but it ended years ago. Not sure if hot glue would work in this case since this part moves.
I watched you do the repair video pretty good but can you help me if you are out there I am trying to open my door so I can take the panel off my handle is broken it is doing exactly what you were saying it is doing please help me how do I open my door
I havent had that issue, the door would still open for me but I think your best bet is to get yourself a lockout kit or another name for it is a slim jim for car door. In my video you can see where that lock unlock rod is so you should be able to rich it with your window open with that tool to get your door open, you can get that tool online or your local automotive store. Good luck.
Thanks for the video, you saved me alot of time and headaches trying to figure out the problem with mine and fix it..👍
Great video and innovative fix. I'm by no means we'll versed mechanics and decided to take on the task of fixing the door handle on my girlfriends Nissan Rogue. I got it done however I'm having a stressful time trying to get the lock to line up with that screw on the side of the door any idea why? The screw is hitting just before the hole on the locking mechanism.
something must be in the way, make sure its all flush on the door inside and the mechanism. Went back in easy for me, kind of.
Absolute fabulous video, and great detail/explenation. Thank you.
But how did you open the door to fix it?? I can’t get the door to open so I can do the Job on my Rogue!! Thank you 🙏🏼
This door opened from the inside, guess i was lucky.
How did you get the door open so you could start working on it?
on the replacement handle on driver side keyless as they aree designated are - does it have to be reprogram?
I dont think so but Im not sure.
I have the same issue but during the winter. I'm not able to open it from inside and outside. But in summer time everything is ok. Strange.
same here on my 2012
@@stackerforson7180
same as me too, rogue 2011.
Same, i think the original recall, circa 2010(?) even mentioned cold as a factor. Mine happened 2x during freezing weather.
Recently purchased a used 2020 nissan rogue and it started doung this after a month bru and now im fixing it myself cuz the dealership i bought it from wanted to charge me wayyyy too much to fix it
How do you remove that black handbar from I side because I can't get it out
is it loose? theres a bolt in the door on the side where the latch is, if u already took that out then just move it around, it came out for me so it should come out for u.
i need to do this on mine it was the passenger side that stopped working since theres no key lock there it should be easier?
most likely, less stuff to take apart.
@@cruizinmax4017 i will likely do it the way you did it, i dont feel like removing the window so ill just tape it in the fully closed position
It's easier and faster if you take off the speaker so you can access the window rail with your hand and align it to screw it on.
great tip, thanks
I HATE, HATE, HATE my 2013 Nissan Rogue. Worst car I’ve EVER bought.
Same my 2010 rogue drivers side has been hell. The exterior handle broke during inspection. Fixed it....then the window wouldnt roll up or down....fixed that...now you cant open the door from the inside and it's the front driverside door
Hi, have same problem today, cannot open door from handle outside but from inside can open with nissan navara np300 2017 year this, be same problem to repair?
Sounds like it, these cars most likely share the same parts.
Thanks for the video! Very helpful
Cool, Thank you for your video, I think i met the same issue, any method I can remove the front passenger door panel without open it?
without opening the door? no
Hi there, very informative, thank you. But I still have a question, ¿how do you remove the lock cylinder? Thanks
the whole handle assembly with the lock cylinder is held on with one torqs bolt (T30) on the side of the door or door jam, remove that bolt and the handle should come out, then the lock cylinder. Dont forget about the yellow clip.
Thank you very much!! Because I was trying to remove that bolt and keeps turning and turning. So, definitely I need to remove both door panels, I guess.
The only problem that I need to fix is the door handle that has broken and of course we can’t open the door. But once again, thanks a lot, I’ll try the yellow clip this time.
I have exact same problem but I can’t open the door from inside or out what can I do? can’t seem to find anything on TH-cam.
try opening it from the outside down the window seal with a slimjim like cops do, you basically need to grab the rod that operates the handle.
I fixed this problem on my lady's car passenger side 3 years ago. Now her driver side is broken.
Great video thanks man! This rogue has really been a terrible car
Thanks, but how did you get thet door open to fix it?
My door opened from the inside, if yours doesnt then you have more issues. This isnt my car so I couldnt tell ya if theres something you can remove from the door panel and try to reach in to pull that cable.
@@cruizinmax4017 can you explain how to open door if one can't open it from the inside?
This is how we got the door open when it was locked from both the inside and outside!
th-cam.com/video/lKi2n8ubfAE/w-d-xo.html
Thanks fixed my problem
Now I just need to figure out how to get my door open to take it apart to fix it being stuck shut
can do same thing in qashqui?
possibly....not sure...im sure you can figure it out.
Hey congratulations man. 770 subs. And 30.000 plus views on this video. Great job 👍👍👍👍👍. I think you be the next Scotty Kilmer 😁😁😁😁😁. It’s just that your videos are much better than his.
It was a factory recall until 2014, the local dealer near me said $100 to fix it.
If it is a recall shouldn't the dealer fix a no cost to you?
Awesome info! I’m registered with Nissan to receive all factory recalls on my model (2013) and have no info on that. I’ll be visiting my local dealer this week😬😬😬
@@phyleciastephens9142 if the piece is actually broken inside the door it will cost alot more because it has multiple connections
@@amederward7081 ya exactly. ONLY Nissan would have a recall that expires. I had many trips to dealers before 2014 and never a peep about this recall. Now mine is unlatched/broken again. Never another Nissan, smh.
I would pay someone $75 rt now, not to have to do this again, lol
Is this car push start?
yes
How much dk you think a mechanic should charge for this?
Im guessing about 1hour but I wouldnt be suprised if they would charge 2h. Thats without replacing anything.
Why is there just a part 2
Door will not open from inside or outside
Thanks mate, I got the same kind of job waiting for me, meen!!! subscribed to support the channel. Will see if I will do a video
right back at ya...thanks!
Thanks
You did good 👍🏻
How do you remove that damn yellow clip!!!!
twist it off the rod then pull it off the hole.
So I can fix it
I hope I never have to do this to my 2016 or 2017 rogues. What a pain. I also hope the wife's Leaf is simpler because that one I do have to do. the chrome piece loses a tab that holds it on. What an annoying crap design.
You did good
bro what part of the country are you in I need to pay you to come and fix my wives it looks like a pain in the ass and hers is doing it now it's been doing it for a week Good tutorial though
Try and do it yourself, get in there...
Let's just do it. What about the other 90% of video
Im not sure what you are talking about, the whole video plays for me and theres no part 2. Its just one video.
7:31
NEVER EVER BUY A NISSAN AGAIN!! ive replaced so many mechanical parts of my 2014 nissan select. Now the door handle, and no air bags now because it cost $1000. + 200 i pd already for diagnostic 😡😡 so Hate Nissan, so so frustrated!!
Yes, I work on plenty nissans on a daily basis.
This video is backwards, show me how to open the door then show me how to fix the problem.
didnt have that issue, door opened from inside
Did not work
Opens from inside but not outside, the ball thing is in its place and pull but does not open
Ill never buy another nissan. They are complete garbage.
The video is titled door wont open... the video starts with the door open i hate this kind of video
Didn't open from the outside, does open from the inside...not enough room for a bigger title.