I have a 29cc Baja 5T and it's pretty fast with the right tuning, i have an 8000RPM clutch, 20 tooth pinion and 57 tooth spur with a tuned pipe and it drifts around fine, jumps fine, and it fast, i had to change the breaks because of the speed of them little things, i put hydraulic front brakes on to help it stop better, the amount of perfomance mods out there for these type of cars is unreal, i'll be getting a stuffed +2mm stroker crank bigger fuel lines, polished carb and ported head soon
its a 2-stroke , so for the first time, warm it up gently by driving it, max half throttle. Let it cool down fully, repeat the previous again. After warming it up for the 3d time its ready to rip. Break-in = setting the piston-rings to the cylinder. Idling the engine for 6 tanks is just a waste of fuel and time. ( not to mention carbon-buildup on the piston by not reaching optimum heat)
lol i remember 7 years ago when i got one of these, they were a lawn shredder to the grass in the park, just ordered the 5sc ss today, these are great ;)
Check your front wheel alignment make sure both wheels point streight ahead, you can alter the tracking by turning the track rod ends, they are the metal bars by the A arms with the flat spots on them so you can turn them with a wrench, also you might want to check the toe in angle on the back wheels, if one toes in more than the other it can cause it to pull to one side, you can also try turning the rear hub spacers 180 degrees to make the rear wheels streight.
what does the air filter oil do? if you are going to take apart the pull start make sure you hold the parts in as the spring inside likes to shoot all the parts out and unwind itself making it really hard to put back together
After 10 mins of running... The engine stopped and now my pull start won't pull. I was running it in wet conditions. Did I maybe get dirt/mud inside... Idk
the break in for the fulie engine that ive been told is run it easy for 1 tank then run it as you want is from some of the most well know modifiers for baja's that i know. idiling for 6 tanks is just a waste of fuel. also the 2 strokes for bicycles maybe a bit different too. like for nitro engines each manufacture has a different break in process for their engine. like hpi they have the ebst break in for their motor each company will be different from the last dealing with the break in proces
Std. or upgraded clutch, both will stopp slipping between the 10-12k mark. Aftermarket clutch such as lauterbacher clutch will only improve smooth acceleration, not top speed.
Hi. I am looking for a replacement engine for my HPI RS4 EVO3 RTR. HPI PART # 15107 They are discontinued but doesn't someone have these engines? I would appreciate some direction. I bought it and it was supposed to be new. It came in a sealed box and was brand new stock. The engine blew. Not sure what happened. Needs a piton, sleeve and drive shaft. Too much money and parts not available. Anyone reading this with an idea for me let me know. I don't want to fit another engine in. Don't have the parts or the time.
i up-graded my stock 26cc engine to a 30.5cc. If you want more power and acceleration then this is a vital up-grade. Also, By any chace, if anyone has a Kingmotor Baja 5B, Then you should up-grade the engine and carby any way. I have a KM and my engine and carby were, well, Shit. slow acceleration and very little top end speed. Apperently if you try to tune a kingmotor carby, the carby wont hold that possition for long. So if you are happy with the engine, then upgrade the carby
It stops dirt from getting into your engine. If you don't put it on then you'll get dirt in your engine and the dirt will scratch the engine's walls leading to lack of performance and eventually complete engine failure.
Yes actually i do know about 2-stroke engines. A stuffer crank can improve performance and strengh, but yes, it will not increese the top speed. If you run a stock clutch, it is more likely to slip inside the clutch bell, if you run a 4 shoe race clutch, then it is not likely to slip, therefore you will get better speed.
I cant believe HPI has stuck with that long wheel base for so long , I chopped 1" off my chassis and it no longer nose dives or loops out easily . Its not that the front end is too heavy , its that the weight is leveraged to far forward.. OHH and about 1" wider....Are you listening HPI?
sreelal roy aliexpress. And here is a tip. Get a killswitch... and a better battery 3000 to 4600 mah is good!!!!. And!! Upgrade the steering servo.... jx 2060 is a good one and is pretty good for the money. And for gas!!! 40ml oil for 1L of fuel. And buy a good transmitter... i have a spektrum DX4C but there are cheaper ones. If you get these things my friend you are set!!! And!!!!! Better battery charger the IMAX B6 mini is prefect. Not the fake one butt the real one!! Check on youtube how to spot a real and a fake one. Have fun my friend!!!!!
However, idling it for 6 tanks of fuel wouldn't hurt. However, I find it strange. The 2-stroke engines for bicycles require a break-in process. The Fuelie engines and others alike aren't much different. Why does the Fuelie get excused from the break-in process?
The fist day i got my Baja 5B, i reved the shit out of it. Didn't bother with the break-in process. I personally don't believe in it. It performs excelent, up to 110km/h and uses a tank of fuel in about 40 minutes. but i have a 30.5cc engine. Not the stock 23cc or 26cc depending on which kit you bought.
The engine in a car may not be a small engine, but it still must be broken-in. So do the 2-stroke gas engines for bicycles they have in California. Those must be broken-in.
Do you know anything about 2 stroke engines? A 4 shoe clutch does not improve high rpm, and a stuffer crank actually decreases top speed. I don't believe 85kph, put a gps on it or use a radar gun, and you'll get no more than 70kph... If you're running stock gearing that is. Obviously top speed does depend on track/road surface and tire choice as some have a different diameter, so don't point out the obvious mate. Good luck getting 110kph...
mate 91% octane can be used on high compresion engine like the 30.5cc engine which need a different oil mix ratio 32.1 mix any thing under 91% octane will screw a expensive engine so use 91% or 95% thats if you can get it becasue our gas staions in the uk have 91% and thay have 97% octane in other places but my nearest sells 91% octane which is plenty for what i need for a 30.5cc engine upgrade for a lozi 5t
Seems like they totally disregarded the break-in process. A fat birdie told me to break-in a Baja's gas engine, let it idle for 6 tanks. That's what I call time consuming.
"There is no danger of over priming the engine" is HORRIBLY wrong!!! You can easy flood an engine by over priming. other than that this video is spot on. But that comment is waaaayyy wrong, don't over prime ever. Over priming will foul plug and cause huge headaches!!!
there really isnt a break in rocess. and its not idiling 6 tanks of fuel. for the first tank you run it less then 3/4 throttle and very the entire tank. after that just run it like ya stole it.
+dickvancock1 I also was like wtf, one gas tank of about 700ml and a "supposed" 2000mah battery last for 15 minutes powering 2 servos? But I also think he said FIFTY and not fifTEEEEEEEN
WRONG!! There is one danger issue with over priming the engine, and that is if the intake of the cylinder is open and you prime it full then pull the cord. Most unlikely to happen but it can. Then you can actually bend the piston shaft! If unlucky.
I never said it definitely goes 110km/h, i said i could go up to 110km/h. Im running a stuffer crank and a lauterbacher 4 shoe racing clutch. My engine would maybe reach 85km/h but i have never cheked the actual performance of it. It also depends on what tyres your running and what conditions your running the baja on. If you use slicks and your on dry road then you willget a higher speed than if you were using dirt buster on grass or dirt. So when did you learn to troll fuck flaps
![ใจดำกับฉันก่อน - วงทัพห้า [Official MV]](http://i.ytimg.com/vi/I48wa4qurAU/mqdefault.jpg)
Old video material, but still all these HPI video's are one of the best instructional video's ever.
I wish they would return the old version of the baja with the purple parts and nice orange body cover
I have a 29cc Baja 5T and it's pretty fast with the right tuning, i have an 8000RPM clutch, 20 tooth pinion and 57 tooth spur with a tuned pipe and it drifts around fine, jumps fine, and it fast, i had to change the breaks because of the speed of them little things, i put hydraulic front brakes on to help it stop better, the amount of perfomance mods out there for these type of cars is unreal, i'll be getting a stuffed +2mm stroker crank bigger fuel lines, polished carb and ported head soon
Good but you should have a 54t spur gear with that pinion, oterwise it won't fit or you make a mistake here at describe it
its a 2-stroke , so for the first time, warm it up gently by driving it, max half throttle. Let it cool down fully, repeat the previous again. After warming it up for the 3d time its ready to rip. Break-in = setting the piston-rings to the cylinder. Idling the engine for 6 tanks is just a waste of fuel and time. ( not to mention carbon-buildup on the piston by not reaching optimum heat)
lol i remember 7 years ago when i got one of these, they were a lawn shredder to the grass in the park, just ordered the 5sc ss today, these are great ;)
15:00 pull-start disassembly and clean. Excellent.
Check your front wheel alignment make sure both wheels point streight ahead, you can alter the tracking by turning the track rod ends, they are the metal bars by the A arms with the flat spots on them so you can turn them with a wrench, also you might want to check the toe in angle on the back wheels, if one toes in more than the other it can cause it to pull to one side, you can also try turning the rear hub spacers 180 degrees to make the rear wheels streight.
Really a Great video mate! Thank You
18:50 carby settings - great!
very informative. can't afford it anyway xD
what does the air filter oil do? if you are going to take apart the pull start make sure you hold the parts in as the spring inside likes to shoot all the parts out and unwind itself making it really hard to put back together
Hi mine is getting delivered in a min so do I change shock fluid or do I leave it for a few weeks
I miss the hpi purple
Orange was better.
I wish I have one of those and I like the sound of a 23 cc 2 stroke engine and 32 cc and a 35 cc engine
Can I use a 7v battery in my exeed hannibal 5th scale gas truck ? For the receiver and servos? Ty
What make a fifth scale gas car wheel term when you crack it
yes usually 92 octane and 2 stroke oil, with a mixture of 20:1 or 25 :1
So no specific break-in ? Like running idle for 15 mins, then let it cool down for 15 mins and repeat every time with 1/4 throttle more ?
This looks like an educational video filmed in the 70s. WTF HPI.
LifeInRecoil I was 6 when that video was released now nearly 20 (intro)
ForTruth NotError if u where 6 you would be like 15 now not 20
Lol
Need help?? Got a Baja 5 b it has a rattle in the engine when I pull the cord. And goes through spark plugs like nothing?
@littleboblives the air filter is for the keep some durt out to make sore that there is noting going in to the engine onlye air
After 10 mins of running... The engine stopped and now my pull start won't pull. I was running it in wet conditions. Did I maybe get dirt/mud inside... Idk
Cool i love baja
THISS i got it and its the best choice you can make
the break in for the fulie engine that ive been told is run it easy for 1 tank then run it as you want is from some of the most well know modifiers for baja's that i know. idiling for 6 tanks is just a waste of fuel. also the 2 strokes for bicycles maybe a bit different too. like for nitro engines each manufacture has a different break in process for their engine. like hpi they have the ebst break in for their motor each company will be different from the last dealing with the break in proces
No break in procedure with gasoline engines?
so basically the rule is 1 battery per tank until u recharge it .....great vid cheers
How to keep the idle needle in factory settings
does it have a ideal
where can I buy baja 5b ss?
So never leve gas in the tank damm I do that I didn't know that does anyone know we're I can get a muffler a good one
recently, I got 5b ss. but i can't make it go in straigh line . why is that ?
you can buy a 30.5cc engine and a tuned pipe
i want a performance upgrade on a lozi 5t 4wd
Seems like the engine isn't too good in the low revs?
i am living in VietNam,so can you ship it for me???
Std. or upgraded clutch, both will stopp slipping between the 10-12k mark. Aftermarket clutch such as lauterbacher clutch will only improve smooth acceleration, not top speed.
Hi. I am looking for a replacement engine for my HPI RS4 EVO3 RTR. HPI PART # 15107 They are discontinued but doesn't someone have these engines? I would appreciate some direction. I bought it and it was supposed to be new. It came in a sealed box and was brand new stock. The engine blew. Not sure what happened. Needs a piton, sleeve and drive shaft. Too much money and parts not available. Anyone reading this with an idea for me let me know. I don't want to fit another engine in. Don't have the parts or the time.
Whats the name of the charger as i seem to have misplaced mine :D
I'd recommend this charger from our current range for the receiver pack:
www.hpiracing.com/en/part/118051
Dónde se consiguen?
i up-graded my stock 26cc engine to a 30.5cc. If you want more power and acceleration then this is a vital up-grade. Also, By any chace, if anyone has a Kingmotor Baja 5B, Then you should up-grade the engine and carby any way. I have a KM and my engine and carby were, well, Shit. slow acceleration and very little top end speed. Apperently if you try to tune a kingmotor carby, the carby wont hold that possition for long. So if you are happy with the engine, then upgrade the carby
what is the use of air filter oil? and what will happen if i didnt put air filter oil?
It stops dirt from getting into your engine. If you don't put it on then you'll get dirt in your engine and the dirt will scratch the engine's walls leading to lack of performance and eventually complete engine failure.
What about 87 octane? That's standard in my area (87, 89, 93)
Yes actually i do know about 2-stroke engines. A stuffer crank can improve performance and strengh, but yes, it will not increese the top speed. If you run a stock clutch, it is more likely to slip inside the clutch bell, if you run a 4 shoe race clutch, then it is not likely to slip, therefore you will get better speed.
Don't lie
@leeadamaa dude standard 95 and 98. is 89 en 92 in the eu
cool
can you fit a obr 30.5cc engine in this car?
Seemingly Suprized yes you can bud
cool
you can fit 45cc engines too
Does it have a reverse gear ?
Joseph Geoji no only forward and brake
can we use the fuel from petrol station or we should make it plzz help
Yeah nah yeab nah
95 is standard in UK I run my golf on 98 from shell
And why are you saying that?
I cant believe HPI has stuck with that long wheel base for so long , I chopped 1" off my chassis and it no longer nose dives or loops out easily . Its not that the front end is too heavy , its that the weight is leveraged to far forward.. OHH and about 1" wider....Are you listening HPI?
The wheel base is distance between the wheels...
Where do I get hpi Baja RC in India...
Please reply
sreelal roy aliexpress. And here is a tip. Get a killswitch... and a better battery 3000 to 4600 mah is good!!!!. And!! Upgrade the steering servo.... jx 2060 is a good one and is pretty good for the money. And for gas!!! 40ml oil for 1L of fuel. And buy a good transmitter... i have a spektrum DX4C but there are cheaper ones. If you get these things my friend you are set!!! And!!!!! Better battery charger the IMAX B6 mini is prefect. Not the fake one butt the real one!! Check on youtube how to spot a real and a fake one.
Have fun my friend!!!!!
this video demonstrates everything owners don't do
they should make a 30.5cc baja with 4wd
Some one messed with my remote/pushed buttons now my remote does not read my car...please help?
Re bind the remote and receiver
Hey can you guys do a breaking in video
It's not hard to break it,in, just drive it around slowly and use a full tank and then it's all good
Tylar Foster now i know that. but im not getting an hpi product
Sunaco Ultra is like 94 octane.
One if the highest grades.
89 is more like a standard octane
can same one guide me how many turn i need to do for the carburetor adjusting ?( its very fast in the video ) thanks
do i need to break it in?
Juppp
However, idling it for 6 tanks of fuel wouldn't hurt. However, I find it strange. The 2-stroke engines for bicycles require a break-in process. The Fuelie engines and others alike aren't much different. Why does the Fuelie get excused from the break-in process?
I think he forgot to loctite
The fist day i got my Baja 5B, i reved the shit out of it. Didn't bother with the break-in process. I personally don't believe in it. It performs excelent, up to 110km/h and uses a tank of fuel in about 40 minutes. but i have a 30.5cc engine. Not the stock 23cc or 26cc depending on which kit you bought.
They run on petrol (gas) and that 2 stroke oil!
Just to say mate you don't need to use a comma if you use the work ( and ) they serve the same purpose :)
standard 95 to 98?!!?!?!?!? i only get 89-92 octane content???
The engine in a car may not be a small engine, but it still must be broken-in. So do the 2-stroke gas engines for bicycles they have in California. Those must be broken-in.
Is the hpi stock radio reliable???
JRC i've had a runaway with it, so I don't use it anymore.
That car looks bad ass fuck where did you buy that. I liked and I loved all of your videos so I had to subscribe.
SONG??????????????/
what would happen if i ran the same gas from my weedeater in it?
Guess this is a video for people who never had to run a 2/4 stroke gas engine, sounds a bit funny. lol
How is it funny??
Why Fuelie and not Zenoah?
Saving money
Can it make a cup of tea?
and some biscets?
typical british xD
Nice BAjA :0)
Krispy I'm British
Can it go to the shop for some krisps
Do you know anything about 2 stroke engines? A 4 shoe clutch does not improve high rpm, and a stuffer crank actually decreases top speed. I don't believe 85kph, put a gps on it or use a radar gun, and you'll get no more than 70kph... If you're running stock gearing that is. Obviously top speed does depend on track/road surface and tire choice as some have a different diameter, so don't point out the obvious mate. Good luck getting 110kph...
Jesus Christ man you want me to use race fuel???????!!!!!!!!! there is no regular 95 octane all we have is 92 and 115
😆
In Europe we do have 95 and 98 only
mate 91% octane can be used on high compresion engine like the 30.5cc engine
which need a different oil mix ratio 32.1 mix
any thing under 91% octane will screw a expensive engine so use 91% or 95% thats if you can get it becasue our gas staions in the uk have 91% and thay have 97% octane
in other places but my nearest sells 91% octane which is plenty for what i need for a 30.5cc engine upgrade for a lozi 5t
100th comment!
anyone watching in 2015
nope 2016 but i have watched this in 2015
Will Brewer I have to
2017 tho
2019🤦🏾♂️
1/5 rc car large scale
Baja.
He said back and forward it doesn’t even go back 9:25
Standard octane is not 95 !
That is among the highest....
Let's be accurate...
+GGobblin It is in Europe
95 Octane RON, it similar to 91 Octane US rating system.
It's 95 RON, not 95 AKI.
Put the car in the ground with the ra-radio turned on
Seems like they totally disregarded the break-in process. A fat birdie told me to break-in a Baja's gas engine, let it idle for 6 tanks. That's what I call time consuming.
its the same stuff. im not sure about the ratio mix you use but the engine is basically the same thing.
تصدقون ي اعيال ان السياره الي ف المقطع معي
بتعرف فيهم ؟؟؟ .... انا من جديد شريت سيارة 29cc والبوجي يضل ينحرق .... في سبب معين لينحرق ؟؟؟
"There is no danger of over priming the engine" is HORRIBLY wrong!!! You can easy flood an engine by over priming. other than that this video is spot on. But that comment is waaaayyy wrong, don't over prime ever. Over priming will foul plug and cause huge headaches!!!
there really isnt a break in rocess. and its not idiling 6 tanks of fuel. for the first tank you run it less then 3/4 throttle and very the entire tank. after that just run it like ya stole it.
receiver pack lasts for 15 mins and loads for 6 hours lol
no , 1h
no 55 min
+tarikتث paris 1كدسسبظبللدج
+dickvancock1 I also was like wtf, one gas tank of about 700ml and a "supposed" 2000mah battery last for 15 minutes powering 2 servos? But I also think he said FIFTY and not fifTEEEEEEEN
95 octane? Nigga dis ain't a race track. Supreme is only 92/93 depending where ya go
Where I live, 95 is everywhere.
race fuel is 102 to 105 octane 95 is standard pump fuel
Well.. here 98 octane is kinda standard. :)
110kph? Yeah sure... Unless you are running different gearing or a 2 speed. A standard baja will go no more the 60-70kph.
Is hard to put a 2 speed on them bro?
US $619.99
go with the setting they say 25:1 50:1 will hurt it
if your unhappy with the speed.
you can buy 62 cc engine, instead 26cc that comes with it.
deal with it nooby.
Hahaha this is ancient
They seem so boggy and kind of gutless.
WRONG!!
There is one danger issue with over priming the engine, and that is if the intake of the cylinder is open and you prime it full then pull the cord.
Most unlikely to happen but it can.
Then you can actually bend the piston shaft! If unlucky.
WRONG!
those engines are generally broken in in the factory. but hpi is lazy and doesnt do it for you
I never said it definitely goes 110km/h, i said i could go up to 110km/h. Im running a stuffer crank and a lauterbacher 4 shoe racing clutch. My engine would maybe reach 85km/h but i have never cheked the actual performance of it. It also depends on what tyres your running and what conditions your running the baja on. If you use slicks and your on dry road then you willget a higher speed than if you were using dirt buster on grass or dirt. So when did you learn to troll fuck flaps
i looked it up, and i hate it.
its ugly and uncool.
What put a geek on it? And a boring as hell voice commentator?
boring
i found it very helpful.
nice thanks