Injora Metal Gear Servo - Injora 66T Brushed Motor for Axial SCX24 - Install and Run
ฝัง
- เผยแพร่เมื่อ 19 ต.ค. 2024
- Links to everything used in this video:
Injora High Clearance Links Deadbolt/Betty: amzn.to/3vEJCdk
Injora High Clearance Links C10/JLU: amzn.to/3K72JBD
Injora Servo w/ Aluminum Mount and Servo Horn: amzn.to/386I5o4
Injora 66T Brushed Motor w/ Motor Mount: amzn.to/3xEqgre
Links to everything else I upgraded on my SCX24 Deadbolt:
Injora Aluminum Axle Housings Front and Rear: amzn.to/3R4z01h
Treal Brass Diff Covers: amzn.to/3a0E0zk
Treal Brass Steering Knuckles: amzn.to/3uDebiE
RZXYLRC Aluminum Axle Housing (Front and Rear): amzn.to/3A0eswY
Dynamite Barrage Motor & Pinion Gear: amzn.to/3niJ5tc
Treal Aluminum Transmission Case: amzn.to/3vESi2I
Treal Aluminum Gearbox Cover: amzn.to/3GkxxOH
Metal Barrage Motor Plate Gearbox Adapter: amzn.to/3EaPehN
Injora Aluminum Skidplate: amzn.to/3EeOsAi
Treal Beadlocks: amzn.to/2XjL0EO
Treal Extended Wheel Weights: amzn.to/3aMaDkN
RC4WD Rok Lox Tires: amzn.to/2YXb4Gi
Front Aluminum Links for 4 link conversion: amzn.to/2W2Hyxo
Treal Aluminum Shocks: amzn.to/3gfLQcr
Kinetic KMS Double Barrel Aluminum Shock kit: www.ebay.com/i...
Kinetic KMS Double Barrel Stock Shock Kit: www.ebay.com/i...
Dynamite Hex Driver: .050”: amzn.to/3ghrxeU
Axial SCX24 Deadbolt: amzn.to/38ZLT96
KYX Aluminum battery tray: amzn.to/2Td3GDX
Hot Racing Aluminum Front Bumper: amzn.to/3oJy1FY
Hot Racing Aluminum Front Bumper Mount: www.ebay.com/s...
Hot Racing Rear Bumper Body Mount: www.ebay.com/s...
Hobby Park Aluminum ESC Tray and Shock Mounts: amzn.to/3fuvZ9H
I am an affiliate of Amazon, Gearbest and Banggood. This means if you purchase anything using any links I provide in any of my videos, I get a small commission and it helps me out with funding this channel to bring more content. Thank you to everyone who had already purchased items through my links. You are all awesome!!
3RD TIME'S THE CHARM! definitely a climber now!
Yeah it stuck right to the dam and wanted to go. I’m more than sure it will make it to the top…as long as I put loctite on the wheel nuts.
You know, you can drastically lower the weight center and load up the front axle by swapping the battery and the esc location. Get rid of the rear tray completely, and pinch the esc between the rails with foam tape. The front tray can be trimmed to hold the battery down low in the frame in front of the motor.
I also removed the front bumper, and the rails in front of the shock mounts for more servo travel. Then body mounted the lights.
Be well, and have fun.
I'm getting the Mofo Ugly AF chassis to move everything around. My front bumper is gone too when I did the four link. Thanks for watching!
That is so darn awesome. Love everything about it.
Your right the red links look so much better and I am not just saying that
I am really liking the look of those red links.
I like this one a lot!!! Been so long since i have had any r.c. car or truck!!! Great Review!!
When tightening your steering servo horn, you can hold the horn with your fingers, so that you can get that last little bit of torque onto the screw in a controlled way…aka snug.
P.S. Shoutout to INJORA!
I didn’t want to over tighten. The servo holds its position pretty good that I felt it was snug enough. Yes shout out to Injora!
@@ReadytoRunRC yes, if one turns lightly until the servo starts to give that prevents stripping out the delrin. an especially good idea at this scale.
Thank you 😎👍
The camera doesn't do any justice for the angle of that dam, or the height. I'm sure it is massive in person!
It's 100 feet high. It's pretty tall and yeah it doesn't do it justice.
I wouldn’t suggest doing any grinding on the motor shaft of your motors. Because metal shavings are likely to end up sticking to the magnets inside the motor.
Masking tape over the holes. 🙂👍
Great video. Rig is lookin really good. Could be me but watching your tires. Still looks like you have bent axle.
Thanks. It came a long way. I think you’re right about the axle. The front left has a little wobble to it.
@@ReadytoRunRC ive been going threw the same thing.. im finally going to just spend the money an get yeah racing axles. Even though it will cost me more for shipping then the product itself lol.
@@rcpatienceraw9751 that was the first I ran it since it fell off the ledge. I only noticed wobble when I was editing the video. I still have the fronts from the axle kit I bought so I’ll swap them out before I climb the dam. Shipping rates are the worst.
The servo should be the emax digital servo, just rebranded for Injora (my guess). The emax digital servo is typically a couple dollars more than the analogue.
I was comparing them when I took the emax off and it looked very similar and had the same thoughts as you that it was just a rebranded emax. Everything looked identical except the sticker.
@@ReadytoRunRC
Yeah, Emax has two versions, one digital and the other analogue. The one that everybody puts in their car is usually the analogue. The digital is claimed to be a little better. The injora servo should be the digital version of the emax.
Awesome
i put this motor and it screams,i'm repositioning pinion and gear 3 times and it continues,i did something wrong?
Not sure what’s wrong. If it’s not the mesh then I can’t think of an answer to your problem.
So when pulling back on the throttle control and if it did go in reverse and you want it to go forward when pulling back couldn’t you just change directional on remote?
I’m not sure where there’s anything on the remote that changes the direction for throttle control. The only thing I see that you can reverse is for channel 1 which is for your steering servo so you can have reversed controls for steering.
@@ReadytoRunRC man you are correct I have several scx24’s and the Jeep gladiator does have throttle reverse on the remote so when I made my comment I assumed they all had it..lol. I’m throwing portal axles on a few and the portals run in reverse so the gladiator is just a matter of flipping a switch but on the c10 and deadbolt I’ll have to do your method. Sorry for the confusion.
@@tcboffroad3206 that’s ok. Wish it was that easy with the older SCX24’s. I haven’t had my hands on any of the newer version SCX’s. Have fun with your build.
Did you ever go back and see if you can make the climb to the top?
I didn’t. But I am going to try very soon. Maybe even this weekend.
Hello from southeast alaska how's it going today bro
Hello!
How'd you break all that stuff..? Is it because the weight?
No it fell off a ledge into water.
Thanks for your video. Would you mind sharing why you went with the 66t version vs the 50T?
Really I just wanted to test it out. See how it compared to the barrage motor. The barrage motor died so it gave me the chance to run this one as a replacement.
@@ReadytoRunRC how do you like it and what’s a barrage motor?
@@Funcentric I like it a lot so far. Seems to have plenty of power. A barrage motor is the motor that comes stock on the ECX Barrage. A lot of people were swapping that motor with the stock SCX24 motor because it was a much better motor.
@@ReadytoRunRC I see. Okay. Cool. Thanks for the clarification.
Nice thinking about getting one for my nieces rc what top speed does this make to see if it is not to fast
Not sure the exact top speed but it might be like 2 maybe 3 MPH.
@@ReadytoRunRC ok thank you
The worm drive of the SCX24 is ideal for slow speed, where it acts as a mechanical drag brake. So if it’s low speed you are looking for, a tiny truck with a worm drive is ideal.
What’s the top speed of the motor?
Probably like 2-3mph
Where do you buy all this sir?
In the links in the description
Why don't you mention that you have to cut off motor side battery tray Mount
I didn’t even think of it because I already had to do that when I put the barrage motor in and I mentioned that in that video.
can the 66t push more weight then the 50t ?
The 16 extra turns should give it more torque to handle the extra weight. I never tested it against the 50t but in theory yes it should.
Do you have to add grease to the motor gearing?
No you don’t need to.
@@ReadytoRunRC thank you for the answer. I'm doing my jeep scx24 and it's my 1st time doing all this. So thank you for the videos.
@@JollyPirateAhoy you’re welcome. Have fun with your build. Glad my videos are helping you out.
I ordered the same servo and waited all week for it and the first day she broke aha, must have been just a lemon
damn, all those links in the description but not one for the axles
Oh I didn’t realize that. I have to get the link from my axle video and paste it in the description.
I updated the description. Thanks for pointing that out.
@@ReadytoRunRC awesome now wheres that "to be continued" video? haha
Edit: i still dont see it there
@@dirtrider88 it’s my dam climb third try video.
@@dirtrider88 I just saved the links again in the description. Now try. They must not have saved last time.
Lets o the dam
Dam climbing coming right up! Waiting on favorable weather.
Please count me in all giveways
Ok but to enter you have to comment on the giveaway videos. The random comment picker picks comments out of those videos. You can’t just say count me in all of them. The comment picker doesn’t know that.