First of all, I'd like to say you're a life saver and literally the only video I found for the Moto Z Play, and your video was uploaded at the perfect time. Anyways, where would I get the adhesive displayed at 4:38?
So, if my phone works (I can hear notifications and it vibrates and I can shake it to turn on the flashlight and I can use Okay Google), but the screen is constantly in a black screen, is this what I replace?
Great video, many thanks! My screen seems to be working fine after replacement as such, but sometimes after reboot, touchscreen is not working. Rebooting it once or twice (using power button) or factory reset seems to be helping. Do you have any suggestions? Could it be faulty connection or screen or could it be software issue as well?
I'm also having an issue with the touchsceen which may be the same one you're having. It doesn't work unless I apply pressure to near the top of the screen with my thumb. There are several metal pads on the back of the screen in that area which need to make contact to the metal in the rest of the phone. The original screen came with small sticky metal adhesive pads which make the connection happen easier, however I'm unable to find more of them online. Hope this helps.
The part linked in the description claims to be OEM. Are you sure of that? I've been through two of these so far with other sellers and you can tell these are a bit off. On each one, the flex cable design is different from the original (it has a grounding tab that appears to be designed to touch one of the RF shields on the board), the "moto" logo is too dark on the white version, the OLED display is grainy and blotchy at low brightness, and the anti-smudge coating is applied unevenly and has vertical bands running up the glass that reveal themselves when fingerprints get on it. Another thing: in this video, when you applied the pre-cut adhesive, did you run into problems with the sheet being about 0.5mm too long? I'm experiencing this with a couple sheets from one seller. The width of the sheets was spot on, but no matter what, either the top or bottom would just rest on top of the lip of the frame instead of inside it. If I made sure both the top and bottom fit inside the frame, the middle portion would arch up. I bought 10 more sheets from a different seller, but I have serious doubts those are going to be any different.
Really helpfull video. But i have a question at the end of the video you use an "adesive" that has the shape of the screen.. do you buy that appart or it cames with the new screen you bougth? Thanks from argentina!
My moto zplay screen has gone all black but I can hear the phone working in the background. I applied some pressure to the top area and top corners of my screen for a little while and the screen seemed to work for a little while and now, even when I apply pressure on the screen, the screen is still black but phone still working. Do I have the same problem as in the video? Should I try to fix it myself like in the video(not a professional) or should I take it to a professional ?
The screen on motoz2 play had a crack the phone got rained on the phone was still working but the screen is black. tried different reboots no good. what do i need to replace? Thanks
Will this affect the data on the internal memory? I have one of these phones and have some important files on the internal memory that I didn't have a chance to back up before I accidentally shattered my screen. If I can fix the phone it will become my primary again, but at the end of the day I only really care about retrieving the data.
Do you have any suggestions for other stickers or perhaps a tape of the appropriate thickness in order to compensate the replacement of the original adhesive that is at least twice thicker at the top and bottom compared to the sides? Cause I have serious doubts that a single sheet of 0.1mm adhesive you're selling will hold the screen in place like it should)
Recently i had changed my Moto z play display, but later my front flash is not working properly, when we press near flash it will flash but when we take hands then it will not.. Moto Athorized Technician had twiced removed screen and checked still issue is not solved . what maybe the issue with this?
Oh boy, I don't think I can do this at home. Noticed this morning that the left side of my screen is poking out. I don't know the cause, as it doesn't seem to be a battery issue, but not sure...
Good video, but the part that shows the application of the adhesive is confusing. I ordered the adhesive on EBAY. It came without instructions, so I tried to do what he did in the video, but the entire adhesive patch stuck to the phone! I was damn lucky to be able to peel off the inner section (Really stuck to the battery, etc!), leaving the adhesive perimeter. I obviously did something very wrong, but don't know how I could have done it differently. Anyway....It worked (unlike the double sided tape the screen repair place used the first time).
At 4:40? I've actually put the adhesive on a phone, it and that STILL doesn't make sense to me. You need to slow down and show what you are doing with the adhesive away from the phone. At the very least, instructions should come with the adhesive. It IS NOT an intuitive process!
my moto play was dropped in water fr about 1:30mini n den dried it n still touch n display is not working, bt it does turn in n gives de main password page by a sound its identified
the home button sensor works, and from i can tell, everything else looks fine. I dropped it and cracked the screen. would that have damaged something that wouldn't let a new screen work properly? I bought the whole digitizer and followed these directions. The only difference is the seller said I'd have to disconnect then connect the battery again, which I did, to no avail.
hey dude... can you make a guide about repair sim card reader on moto z play. i have a problem with that. i'll be thx to you if you respond my comment and make that guide. thx
You didn't show us how you put the glue on on the actual screen so it sticks onto the body. You know the glue you took off with the heat gun to get the screen off. How and where exactly do you put it on?
A mi me cambiaron la pantalla y al mes, se me ponía en negro y si hacía presión sobre la zona superior, agarraba imagen, andaba todo menos la imagen. Lo mande a revisar y me dijeron que es el dispositivo. Que se puede haber dañado? Desde ya gracias
Seriously i dont get it. The adhesive is weird, I'm freaking out... 1 out of 3 wasted already. I cant understand how that works, the adhesive that came has 3 layers, paper, glue and plastic. The way he puts it doesn't fit with the one i got. If i pull the tab everything comes of
Get OEM Replacement Parts For Moto Z Play ： witrigs.com/d7mbg
OEM AMOLED Screen for Motorola Moto Z Play ： zegsu.com/s/di848
First of all, I'd like to say you're a life saver and literally the only video I found for the Moto Z Play, and your video was uploaded at the perfect time. Anyways, where would I get the adhesive displayed at 4:38?
www.witrigs.com/custom-lcd-supporting-frame-sticker-for-motorola-moto-z-play
Too many cut scenes, show us how you struggled with the connections so people dont think its super easy
So, if my phone works (I can hear notifications and it vibrates and I can shake it to turn on the flashlight and I can use Okay Google), but the screen is constantly in a black screen, is this what I replace?
Great video, many thanks!
My screen seems to be working fine after replacement as such, but sometimes after reboot, touchscreen is not working.
Rebooting it once or twice (using power button) or factory reset seems to be helping. Do you have any suggestions? Could it be faulty connection or screen or could it be software issue as well?
I'm also having an issue with the touchsceen which may be the same one you're having. It doesn't work unless I apply pressure to near the top of the screen with my thumb. There are several metal pads on the back of the screen in that area which need to make contact to the metal in the rest of the phone. The original screen came with small sticky metal adhesive pads which make the connection happen easier, however I'm unable to find more of them online. Hope this helps.
Sir, need to check the screen cable buckle is clasped.
Does the adhesive two-sided tape come with the screen replacement
thanks a ton! i didnt have a heatgun but i used a space heater and let the phone sit there for a little while and that glue let go. works good again.
The part linked in the description claims to be OEM. Are you sure of that? I've been through two of these so far with other sellers and you can tell these are a bit off. On each one, the flex cable design is different from the original (it has a grounding tab that appears to be designed to touch one of the RF shields on the board), the "moto" logo is too dark on the white version, the OLED display is grainy and blotchy at low brightness, and the anti-smudge coating is applied unevenly and has vertical bands running up the glass that reveal themselves when fingerprints get on it.
Another thing: in this video, when you applied the pre-cut adhesive, did you run into problems with the sheet being about 0.5mm too long? I'm experiencing this with a couple sheets from one seller. The width of the sheets was spot on, but no matter what, either the top or bottom would just rest on top of the lip of the frame instead of inside it. If I made sure both the top and bottom fit inside the frame, the middle portion would arch up. I bought 10 more sheets from a different seller, but I have serious doubts those are going to be any different.
Really helpfull video. But i have a question at the end of the video you use an "adesive" that has the shape of the screen.. do you buy that appart or it cames with the new screen you bougth? Thanks from argentina!
Is screen sticker. www.witrigs.com/custom-lcd-supporting-frame-sticker-for-motorola-moto-z-play
My moto zplay screen has gone all black but I can hear the phone working in the background.
I applied some pressure to the top area and top corners of my screen for a little while and the screen seemed to work for a little while and now, even when I apply pressure on the screen, the screen is still black but phone still working.
Do I have the same problem as in the video? Should I try to fix it myself like in the video(not a professional) or should I take it to a professional ?
If you are not completely sure or have relevant experience, it is recommended that you get it done by a professional.
The screen on motoz2 play had a crack the phone got rained on the phone was still working but the screen is black. tried different reboots no good. what do i need to replace? Thanks
Will this affect the data on the internal memory? I have one of these phones and have some important files on the internal memory that I didn't have a chance to back up before I accidentally shattered my screen.
If I can fix the phone it will become my primary again, but at the end of the day I only really care about retrieving the data.
Not at all, the screen and memory are not related at all, so changing the screen will not affect it.
Do you have any suggestions for other stickers or perhaps a tape of the appropriate thickness in order to compensate the replacement of the original adhesive that is at least twice thicker at the top and bottom compared to the sides? Cause I have serious doubts that a single sheet of 0.1mm adhesive you're selling will hold the screen in place like it should)
Hi sir,The adhesive thickness is 0.25mm. we've tested the adhesive and it's stick enough to hold the screen tight.
It's there a video for just the glass?
Hey I can't turn it off, the screen is black do I just wait? Also did it should it boot into factory mode, like in the video?
How you Stick the display ? what is that thing ?
Recently i had changed my Moto z play display, but later my front flash is not working properly, when we press near flash it will flash but when we take hands then it will not..
Moto Athorized Technician had twiced removed screen and checked still issue is not solved .
what maybe the issue with this?
plz help me out as mobile is getting on by just display not working
I have a motor z play that's broken but no wer in Namibia can they fix it so sad 😣
I want only LCD Glue Sheet , shopping link plz
Oh boy, I don't think I can do this at home. Noticed this morning that the left side of my screen is poking out. I don't know the cause, as it doesn't seem to be a battery issue, but not sure...
Good video, but the part that shows the application of the adhesive is confusing. I ordered the adhesive on EBAY. It came without instructions, so I tried to do what he did in the video, but the entire adhesive patch stuck to the phone! I was damn lucky to be able to peel off the inner section (Really stuck to the battery, etc!), leaving the adhesive perimeter. I obviously did something very wrong, but don't know how I could have done it differently. Anyway....It worked (unlike the double sided tape the screen repair place used the first time).
Hi. sir Look at the video where the adhesive needs to be removed.
At 4:40? I've actually put the adhesive on a phone, it and that STILL doesn't make sense to me. You need to slow down and show what you are doing with the adhesive away from the phone. At the very least, instructions should come with the adhesive. It IS NOT an intuitive process!
my moto play was dropped in water fr about 1:30mini n den dried it n still touch n display is not working, bt it does turn in n gives de main password page by a sound its identified
Sir, you need to take a newspaper and wrap it in your cell phone and wait for a day to see if it will boot normally.
+Wit Rigs OK but I kept de mobile in sun for drying n after that display is not working
+Wit Rigs mobile is getting ones is coming up to de main android password screen I kno it by de main power off button switch sound
Replace the new LCD screen to try! You know the phone is open, but the LCD screen does not show anything.
I followed this exactly and the screen turns on but I cant get any touch functions to work! Im at my wits ends
Hi，There are many possibilities for this problem, there may be a problem with the motherboard.
the home button sensor works, and from i can tell, everything else looks fine. I dropped it and cracked the screen. would that have damaged something that wouldn't let a new screen work properly? I bought the whole digitizer and followed these directions. The only difference is the seller said I'd have to disconnect then connect the battery again, which I did, to no avail.
Im having similar problems. :/
Bhaiya Motorola one power ka new screen kitne me aa jayega
Great video but seems his answer to every question is "maybe main screen cable not clasped. "
what to do if u have red litmus on it moto z play motherboard too
hey dude... can you make a guide about repair sim card reader on moto z play. i have a problem with that. i'll be thx to you if you respond my comment and make that guide. thx
You didn't show us how you put the glue on on the actual screen so it sticks onto the body. You know the glue you took off with the heat gun to get the screen off.
How and where exactly do you put it on?
What is the adhesive used ? And why isn't it linked?
Is screen sticker. www.witrigs.com/custom-lcd-supporting-frame-sticker-for-motorola-moto-z-play
A mi me cambiaron la pantalla y al mes, se me ponía en negro y si hacía presión sobre la zona superior, agarraba imagen, andaba todo menos la imagen. Lo mande a revisar y me dijeron que es el dispositivo. Que se puede haber dañado? Desde ya gracias
Cambiar una nueva pantalla.
En cuanto $$$ sale cambiarle la pantalla??
Thanks! It worked!
😁
also it's got kinda copper green rust in de display connector.
Did your phone fall? If you fall over, the screen may have gone bad and you need to replace a new LCD screen.
It has been resolved by Lenovo. They accepted to repair it under warranty.
My phone wont come on after plugging in the 2 flex cables What is wrong?
Seriously i dont get it. The adhesive is weird, I'm freaking out... 1 out of 3 wasted already. I cant understand how that works, the adhesive that came has 3 layers, paper, glue and plastic. The way he puts it doesn't fit with the one i got. If i pull the tab everything comes of
Display prize
I think Moto z play has Super Amoled not LCD display
Lg k7 fix glass
My man got three hands