Hunter PGP Rotor Adjustment
ฝัง
- เผยแพร่เมื่อ 14 ก.ค. 2020
- ►Hunter PGP Rotor: amzn.to/4aaFeFn
►Hunter PGP Ultra Rotor: amzn.to/3PkEoxX
Liked our video? Consider supporting us by purchasing this controller through our affiliate links above (we get a small commission), or joining our Patreon: / smartirrigation
Chris from Smartirrigation.com shows the smart way to adjust the spray pattern on a Hunter PGP Ultra rotor. These adjustments work on all residential Hunter rotors, including the PGP, PGP Ultra, and PGJ, as well as the Orbit Voyager II. Chris also warns against tempting shortcuts that can cause costly damage to your sprinklers.
For more smart irrigation tips, subscribe to our youtube channel and visit our official website: www.smartirrigation.com - แนวปฏิบัติและการใช้ชีวิต
Liked the video? Help us make more at www.patreon.com/SmartIrrigation
Thank you very much for explaining this so that anyone can understand how to adjust this sprinkler. I've watched other videos, but none explained this as well as you did. Kudos!
Thanks for the kind words!! I'm glad the video helped you adjust your sprinklers!
I've seen numerous vids on how to set the Hunter rotor right stop and no one explained it better than you. No one mentioned that there is an official Hunter method and an acceptable alternate method. No one said to not use channel locks on the shaft but I always wondered about that. Thank u.
Thanks for great comments.
Best video I have seen for adjusting the hunter heads. Informative in just the right areas
Thanks for the support and feedback! We're glad it made a difference!
Thank you thank you so very much for your educational video of how to adjust it helped me out so greatly adjusting all the sprinkler heads on my one-block condo property with over 150 sprinkler heads and over 30 different zones. Taking it slow Zone by Zone going around adjusting every single sprinkler had getting the coverage that I need for my big fields and small boulevards. 100% thank you
Very glad that we could help and that it made your day a bit easier! Its what we're trying to do!
Great video. Just bought one of these as a replacement. Info was very helpful. 👍
Thanks and glad to be helpful!
Hi Chris. GREAT video. Hopefully it will enable me to set my Hunter PGP sprinkler heard. Thanks!!
Glad you liked the video! Did it end up helping with setting your PGPs?
Thanks for the tips.
Anytime!
Great tip! That'll save me some time for sure!
Glad to help!
I've only seen that end stop adjustment on Rain Bird 5000 heads, I'm definitely going to have to try that trick.
Glad we were able to show you something new! Let use know how it worked out for you
Explaintion will done. Thank you so very much.
You are most welcome!
Good stuff!
Thanks!
This helped thanks!!
Absolutely! Be sure to stop by soon, we hope to keeping making more of these videos if people like them!
Thank you this information. I now see why I am unable to properly, and fully, adjust my sprinklers; I do not have that adjusting tool you showed in the video. Where can I obtain one?
Glad it was helpful!! You can get a pack of 3 on Amazon for about $10, or if your local sprinkler supplier sells hunter then you can purchase a single tool from then!
Thanks. I will try that.
You bet! How did it work out for you?
This is a great tip! Does it also work on the Hunter I-20?
Yes it does.
Thank you Chris! I guess my question was, is it possible to use the “unofficial way“ to rotate the shaft COUNTERclockwise if the right stop is too far right. It looks with Rainbird 5000 you can rotate the shaft in both directions when adjusting the stop. What is your experience? Thanks again for your time!
Yes you can. We do it all the time. It's similar to setting a pop-up spray head that way.
When using the unofficial way I presume you don’t have to hold the ribbed part below the shaft when turning…since it won’t affect how it’s secured into the housing?
Thank you! I noticed my Hunter PGP will automatically rotate from right to left but then get stuck at the left. If I rotate it a bit more left, it will swing back to the right. However, several heads are sticking to the left (maybe not rotating to the full left stop). What is going on here?
It sounds like the gears inside these heads are stuck or broken. Since these heads aren't designed to be opened or taken apart, unfortunately it sounds like you will need to replace these heads.
What if the right fixed stop is too far to the right? How do you adjust? Thanks!
Two methods. First try turning the whole head in the ground. If that doesn't work you can remove the inside cartridge from the case by unscrewing it, then reposition it where you want and tighten the cartridge back into the case.
So in order to have less right rotation, would I need to spin the head all the way around to the right or can you twist it left?
If you need it to stop sooner in the right direction you would turn the stem or riser (not the top) to the left. Then with the Hunter key reajust the left stop. So twist to left is correct.
@@SmartIrrigation1 Thank you!
How do you turn the head off? I want my system to run but one head is malfunctioning so I am needing to turn off a single head
Replace the malfunctioning head would be my first choice because there is no easy way to turn off just one PGP. Remove and cap it at the fitting in the ground if no longer needed but be carful because it could affect the coverage.
My heads are rotating a full 360, it seems.
Some heads are only 360 degree heads, designed to only spray in a full circle. However, if you have an adjustable PGP, you should be able to use the tool and turn it counter clockwise in the adjustment slot to reduce the arc of the circle that it waters. Hope this helps!
Liked the video? Help us make more at www.patreon.com/SmartIrrigation