I just installed a case saver from Uppracing.. fits a 15 tooth sprocket part#1031. Fits like a glove. Thanks for the heads up! I'm glad I found your video
Im at the end of my big bore upgrade on my raptor 700r. She fires right up and purrs like a mountain lion. I also put on dual full exhaust, FCI and PCV
hey can i ask u a ? i just installed a duel exhaust with pcv and my raptor 700 wont stay on ive messed with the idle but it doesnt fix the problem did u have any troubles like this? and whats a fci? is that a upgraded air filter?
Oem case saver is thin if lookin at it one way, the way intended for use it’s a half inch + which is more than enough to save the case. Has anyone actually seen ( in person ) the chain snap and bind up?
For everyone in the future who wants a temperature sensor there are cheap kits on ebay and amazon that you can buy and install that are nicer looking and cheaper
You got me worried. I have a thermostat that is sticking and that has caused the temp light to come on twice for only about 5 minutes each before i got on some higher speed stuff to cool off the engine and then park it. Hoping i didn’t damage the engine. Got a thermostat on the way.
I have the 2014 model. Can that be placed on the bottom line just forward of the Water pump? If it would work, it would be easier to see down near the foot.
What's the purpose of the exhaust block off plate? Wouldn't more air to burn off the extra gas be a good thing? What problems does it cause down the road, if you don't block it off?
the AIS is a reed valve, the valve can get weak and loose, or build up with carbon and stay open. This will cause a lean condition and engine failure! .
@Richard - I have the same question! I'd assume more air in puts more back pressure on the engine and limits potential flow? I'd think there is a balance point.. Love to see a dyno b4 and after
normally it's needed if you remove the cat(removes some popping) or want to tune the bike(or run an auto-tuner), as you can't get a good reading with extra air getting dumped in.
there are a few different options on the marked. we have actually switched over to one which incorporates 3 mounting bolts of the stator as well which give that option for guys who have already broken their case mount. Its built by a customer and is unbranded.
You missed the most important upgrade. Hugh quality steering shock!!!! Ive been riding 700R for years and let me tell you a good steering shock feels like power steering over the bumps. by far the best upgrade period. now wise up!!!
No way, cuervo is right man, ur engine actually lasting is more important then bump steer. I just bought a brand new 22 700r and these 3 mods will be the 1st things I do!!! I don't run any of my bikes unless I can check the temp.
@@JetSkiBuyFixPlaySellChannel Cool so what does bypassing the EPA crap do for the rider? More HP? Better throttle response? Just to say "Fuck You" to the EPA? And what does that hose go to and is it needed? I don't want a $20 part to ruin my $9,000 machine I'm still paying for...
Hi Mrcuervoracing I wanted to ask with a concern I have I recently bought the ais plate from you and I wanted to ask if I can put this on during the engine break in period hope you get this message
@@AfterHoursWithMrC yeah I asked this question about a year ago and still don’t know lol. I’m thinking it probably don’t do anything or they would have told me so they could sale me one.
Im not a fan of the duals for the 2015 and up head. Ive dyno tested and installed the Barker Duals for the 15+ and i see a few faults, the mid pipe is Hard Mounted, this imo will lead to future failures, excess weight, and performance is LESS then the Monster Single once engine modifications are made!!! We've made nearly 100 Hp thru the Monster Shorty and tested the other contenders on the market on the same engine and it was a HUGE difference in power. The more power over stock the bigger the gap between the Monster and others. The biggest benefit of the Barker Duals is the sound level is QUIET!!
Do you know of a way to get rid of the top speed limiter in 5th on the 2015+ raptors. I’ve heard unplugging the sensor from the clutch doesn’t work anymore.
I hit 79.84mph on my stock 2019 Raptor 700R this weekend. I think it had a tiny bit more left in it too. Do they have a limiter? (not that I really want or need to go any faster)
@@JarofMayonaise I know the 07 700 once in 5th the ecu changed timing curves so it wouldn’t pull but so many RPM in 5th. I put on a dynatek ignition and it did away with that problem.
Good idea. I need to put some on the shelf. Most guys here put a longer swingarm on and the chain makes contact less often with the roller due yo a changed angle and ride height. But yeah idk what the hell they were thinking
808sand Blvke yeah! Changed out for a TM roller with the groove and it got rid of 95% of the noise. If I tightened my chain just a bit it would be gone all together
It's looking like my 08 raptor was better. Never had issue with overheating and I ride trails in the desert at low speeds 90+ heat sometimes 110 and never seen the temp light ON. I do notice alot of heat coming out due to fan being ON almost always. I do wonder at those times what the temp is so I might just get one of those.
When would you ever look at a temp gauge mounted down there?! Again, by the time you do your stock light would be already be on! That's just a waste of time and money... Save it and buy a Trail Tech with temp gauge/gps/tach/mph/etc.
Hello from FLORIDA thanks for your videos they’re very helpful I’m got a used raptor 700 and I want to do some maintenance like engine oil change I see on the manual the recommendation according to my rather I should use 10w40 or 20w40 but which brand should you use for 100% trail/mud ridding?
Hey what's up man great video I just picked up a 2018 raptor 700 R yesterday and I just wanted to check with you regarding that block off plate. Will that void the warranty because I have a two year warranty on the engine and transmission from the dealership that I paid for so I was just curious. Thanks again for the information sir
the dealer can choose to void warranty for any modifications or reason. You can return the bike to stock at any time, just keep all the factory parts handy.
OK awesome I appreciate your advice, i'll be doing these mods pretty soon once the engine is all broke in. I got the same color as the one in the video it is a great looking bike
It's the best looking because you can't afford a special addition they are way better looking but just to me but if you ride a lot of dirt the graphite will be for you
this is a customers bike. there isn't much difference between the SE and the base besides Color and shocks. the shocks are cheap to change, even buying the OEM SE shocks are super cheap. If you think you are somehow Better or Smarter because you paid more to have the "SE" color then you are mistaken. one can easily change all the components and add the bumper and heel guards aftermarket or gytr and upgrade the shocks for the same cost and then not be stuck with a Burgandy red frame.
I've owned several raptor 660 and all were junk. If they have not fixed their design for the 700 then there is no way in hell i will own one of these pieces of shit.
That grey on grey with the black frame is sick! Remember buying my AIS block off from you guys. Definitely recommend CuervoRacing.
Highly agree with the case saver and the temp gauge
I just installed a case saver from Uppracing.. fits a 15 tooth sprocket part#1031. Fits like a glove. Thanks for the heads up! I'm glad I found your video
Found that part comes with a chain roller know what’s that is?
Ive got my temp thru my trail tech vapor. Best investment so far
Thats the cleanest 2018 i ever saw, keep it up
I have an 07 SE2 Raptor 700. Blue powder coated frame with white and blue plastics. sharp lookin bike...
cool tips, gonna get one of these things soon, thanks for the vid!!!
Why, they’re weak . Especially if you build up the raptor just a hair
@@susdadu weak
Im at the end of my big bore upgrade on my raptor 700r. She fires right up and purrs like a mountain lion. I also put on dual full exhaust, FCI and PCV
hey can i ask u a ? i just installed a duel exhaust with pcv and my raptor 700 wont stay on ive messed with the idle but it doesnt fix the problem did u have any troubles like this? and whats a fci? is that a upgraded air filter?
For the Reed valve can you just use a rubber cap cilcone and small hose clamp
Stage 5 fuel controller really opened up my 700R. Then the exhaust and intake.
First thing i would get for that is some heel guards/nerf bars.
Oem case saver is thin if lookin at it one way, the way intended for use it’s a half inch + which is more than enough to save the case. Has anyone actually seen ( in person ) the chain snap and bind up?
I would also recommend draining your coolant and switching to engine ice coolant. I dis that the day i bought my 2014 700r SE.
beautiful quad
What’s your thoughts on a digital thermometer, I’ve seen one online which doubles showing what gear your in as well?
Cheers
honestly, you don't want to see how hot your engine is. It'll scare you a lot.
Love ur videos.. keep up great work! 👍
For everyone in the future who wants a temperature sensor there are cheap kits on ebay and amazon that you can buy and install that are nicer looking and cheaper
You got me worried. I have a thermostat that is sticking and that has caused the temp light to come on twice for only about 5 minutes each before i got on some higher speed stuff to cool off the engine and then park it. Hoping i didn’t damage the engine. Got a thermostat on the way.
That's a beautiful colour
nah nah the best model is the 2017 model. blue and gray
Harley you mean the 2019 ?
@@quadsticiles8403 Ah Yeah thats the 2020 700
I got the 2019 700r GYTR blue black
@@quadsticiles8403 700r and not se? What's the difference only form no function?
Does putting a ais block off on a raptor with a stock pipe affect the tuning negatively? Or does it improve it?
Awesome 👌 getting 2022 raptor soon
Make a video installing the ais block off plate ive been wanting to do it to my 16 raptor
I need a raptor
What are the benefits of installing the air block off plate? I'm a new Raptor owner. Mine is completely stock but I'm looking to do upgrades
curious about this too. is it just that the stock valve goes back quick?
Thank bro
So the monster shorty pipe is the best to get the most out of my raptor? Or do you recommend the regular size can?
I don’t know if it’s me but I like more the face of the old raptor 700
Benjamin sides same
Finally someone !! Benjamin sides I think the same thing!!!
Benjamin sides i like made in japan
My 09 made in jpn is made 100x better then my 15 made in usa.
It’s just you homie. The old ones cool the news ones are real cool. 06-07 models were beastly tho
Do you sell case savers? If not, which one do you recommend? Thank you.
I have the 2014 model. Can that be placed on the bottom line just forward of the Water pump? If it would work, it would be easier to see down near the foot.
Just got my 2023 700R SE with the red frame. Does that AIS block off plate void the warranty?
What's the purpose of the exhaust block off plate? Wouldn't more air to burn off the extra gas be a good thing? What problems does it cause down the road, if you don't block it off?
the AIS is a reed valve, the valve can get weak and loose, or build up with carbon and stay open. This will cause a lean condition and engine failure! .
MrCuervoRacing well, that's not a good thing. I guess a block off plate is a great idea.
YAMAHA'S rule!
Is this an emission thing? Does it increase HP or just eliminate problems later?
@Richard - I have the same question! I'd assume more air in puts more back pressure on the engine and limits potential flow? I'd think there is a balance point.. Love to see a dyno b4 and after
normally it's needed if you remove the cat(removes some popping) or want to tune the bike(or run an auto-tuner), as you can't get a good reading with extra air getting dumped in.
What are those tires
I need to upgrade to one of these I only have the 350 model
I like him so much
then marry him
XD
much appreciated.
Dang that's clean but I got the one with the red frame
1320_club _007 yeah it's Decked out 80 hp all custom
So what the reed value thing for and what will it add by adding the piece
Welcome to 2018 where manufactures need reed valves on 4 strokes to meet epa restrictions.
Would you say this is the best case saver available for the raptor? Want to make sure she has the best protection possible.
there are a few different options on the marked. we have actually switched over to one which incorporates 3 mounting bolts of the stator as well which give that option for guys who have already broken their case mount. Its built by a customer and is unbranded.
Hello! Can I specify a link where to buy such an engine temperature sensor?
You missed the most important upgrade. Hugh quality steering shock!!!! Ive been riding 700R for years and let me tell you a good steering shock feels like power steering over the bumps. by far the best upgrade period. now wise up!!!
Whats the diffrence between that and precision steering stabilizer
No way, cuervo is right man, ur engine actually lasting is more important then bump steer. I just bought a brand new 22 700r and these 3 mods will be the 1st things I do!!! I don't run any of my bikes unless I can check the temp.
Nice
With the ais block off plate help it run cooler because stock is so lean?
What is the advantage of blocking off the reed valve?
Bypass the EPA crap.
@@JetSkiBuyFixPlaySellChannel Cool so what does bypassing the EPA crap do for the rider? More HP? Better throttle response? Just to say "Fuck You" to the EPA? And what does that hose go to and is it needed? I don't want a $20 part to ruin my $9,000 machine I'm still paying for...
@@JarofMayonaise it helps with decel popping.I just cut the hose right above the reed valve cover and plugged the hose.
Don't forget nerf bars !!!
Sorry guys im so lost on the AIS.. if i delete it will it make my bike spit flames or be louder or does it do the complete opposite?
What are the best octane fuels to use at the different ATV horsepower levels and setup's. Stock set up, 50hp-60hp, 65hp-75hp, 80hp+ and up....?.?.?
What matters more about octane rating is your engine compression.
Daniel, where do you buy the temp gauge?
Any recommendations for a big 3 kit for a 2018 raptor 700r SE?
Didn’t the 2011 and maybe 2012 have a temperature gauge that worked like that I know they definitely had a speedometer If I’m not mistaken ?
They did not i don't believe
The special edition models had speedometers
Hi Mrcuervoracing I wanted to ask with a concern I have I recently bought the ais plate from you and I wanted to ask if I can put this on during the engine break in period hope you get this message
What are the benefits of the block off plate?
I was wondering the same thing. Not quite sure the full reason behind changing it
@@AfterHoursWithMrC yeah I asked this question about a year ago and still don’t know lol. I’m thinking it probably don’t do anything or they would have told me so they could sale me one.
do u have a link for the temp gauge?
Nice color
What does that plate even do the ais?
What do you think bout the Barkers duals Big 3 kit?
Im not a fan of the duals for the 2015 and up head.
Ive dyno tested and installed the Barker Duals for the 15+ and i see a few faults, the mid pipe is Hard Mounted, this imo will lead to future failures, excess weight, and performance is LESS then the Monster Single once engine modifications are made!!! We've made nearly 100 Hp thru the Monster Shorty and tested the other contenders on the market on the same engine and it was a HUGE difference in power. The more power over stock the bigger the gap between the Monster and others. The biggest benefit of the Barker Duals is the sound level is QUIET!!
1 pipe per cylinder.
I just installed a block plate and now it’s running hot, anybody experience this slso
Where can i get the blockoff plate?? I have 2017 700r
Jiap Aguilar message us or call 951-743-6328
Also on EBay Ais block off plate link in discription
MrCuervoRacing ok thankyou
Great video with some excellent information. I just found your channel - subbed!
Scott
What big 3 do you recommend for that Raptor 700?
A L B PC5 MONSTER FCI
Monster pipe, fci and pcv. Give us a call and we can discuss options on that.
MrCuervoRacing what will adding those do to your raptor??
Junior Lara safety, safety, safety
what is the big 3?
Do you know of a way to get rid of the top speed limiter in 5th on the 2015+ raptors. I’ve heard unplugging the sensor from the clutch doesn’t work anymore.
I hit 79.84mph on my stock 2019 Raptor 700R this weekend. I think it had a tiny bit more left in it too. Do they have a limiter? (not that I really want or need to go any faster)
@@JarofMayonaise I know the 07 700 once in 5th the ecu changed timing curves so it wouldn’t pull but so many RPM in 5th. I put on a dynatek ignition and it did away with that problem.
Hi! I have a 2020 raptor 700, I just ordered a monster exhaust intake and pc5 do I need that block off plate aswell?
highly recommended. check our eBay listing. MrCuervoRacing ais.
@@MrCuervoRacing thank you!
are the newer ones any different than the older ones?
Bridgette Freihaut frame and suspension are pretty much the same
What aboout the noisy stock bearingless lower chain roller, that was number 1 on my list.
Craig Rodriguez yes, you can replace with the earlier years roller 06-12
MrCuervoRacing oh cool, I put a TM on mine but didn't know when the bearing was eliminated. Thanks
Good idea. I need to put some on the shelf. Most guys here put a longer swingarm on and the chain makes contact less often with the roller due yo a changed angle and ride height. But yeah idk what the hell they were thinking
Craig Rodriguez That’s what that noise is? I always wondered what that damn noise was.
808sand Blvke yeah! Changed out for a TM roller with the groove and it got rid of 95% of the noise. If I tightened my chain just a bit it would be gone all together
Where can i get one of these bike from???
Yamaha dealer ship or a recreational dealer
It's looking like my 08 raptor was better. Never had issue with overheating and I ride trails in the desert at low speeds 90+ heat sometimes 110 and never seen the temp light ON. I do notice alot of heat coming out due to fan being ON almost always. I do wonder at those times what the temp is so I might just get one of those.
If ur fans come on thats usually not good never had my fans turn on amd yes they work
@@TA-jp6df your fan may be working but is your sensors working properly the fan should always kick on from time to time every ride bro
Will that case saver fit with a 15t front sprocket?
yes
MrCuervoRacing awesome, thanks
What size is that coolant hose?
Been looking everywhere on the Internet and I think it is 3/4 inch
mohawk front tires
When would you ever look at a temp gauge mounted down there?! Again, by the time you do your stock light would be already be on! That's just a waste of time and money... Save it and buy a Trail Tech with temp gauge/gps/tach/mph/etc.
How bout a different drain plug
We offer our Drain plug Reducer kit
MrCuervoRacing Where to buy the parts online? How about temp gauge on the handle bar for better visibility?
2:56 U-P-P racing 😂😂😂😁,,, c'mon now! I know y'all got the same picture in y'all heads for a second there, don't front!!!
Where did you get your front tires at
Michael Talbot those are Mohawks. Thru Www.sandtoyzunlimited.com call John , tell him Cuervo sent ya
Oh yeah that’s right my dad knows the owner of it
Hello from FLORIDA thanks for your videos they’re very helpful I’m got a used raptor 700 and I want to do some maintenance like engine oil change I see on the manual the recommendation according to my rather I should use 10w40 or 20w40 but which brand should you use for 100% trail/mud ridding?
I woke use ams oil or Lucas oil or yamalube
I am Spanish and I did not understand, what 3 things are?
RockaBilly A temperature gauge in the tube, a case saver piece that protects the engine case from the chain and a seal piece for the hole in exhaust
Hey what's up man great video I just picked up a 2018 raptor 700 R yesterday and I just wanted to check with you regarding that block off plate. Will that void the warranty because I have a two year warranty on the engine and transmission from the dealership that I paid for so I was just curious. Thanks again for the information sir
the dealer can choose to void warranty for any modifications or reason. You can return the bike to stock at any time, just keep all the factory parts handy.
OK awesome I appreciate your advice, i'll be doing these mods pretty soon once the engine is all broke in. I got the same color as the one in the video it is a great looking bike
these bikes overheat?
no, but any bike can get too hot if abused
Where can I get all three parts?
give us a call 951-743-6328
or email sales@cuervo-racing.com
the AIS plates are listed on eBay
What exactly is the AIS, an air injection system? Is it electronically controlled. Can it be removed without it causing an error code?
Chris Potts yes . No code. An electronic valve controlling a reed valve
MrCuervoRacing. So it goes from the intake to the cylinder head or ?
When you let off the throtle it introduces air in the cylinder right?
Chris Potts yes. Fresh filtered air from intake thru valve them to the exhaust thru a transfer port in the head
Why those front tires look like mine tho 😭
Bc they’re not uncommon
Jaxson Goodman it was a joke because my tires are worn to shit
BIKE
If it ain't a drw case saver it ain't worth buying
Those have quite a few problems they cause in the process of trying to solve a rare one that can be fixed with proper maintenance.
It's the best looking because you can't afford a special addition they are way better looking but just to me but if you ride a lot of dirt the graphite will be for you
this is a customers bike. there isn't much difference between the SE and the base besides Color and shocks. the shocks are cheap to change, even buying the OEM SE shocks are super cheap. If you think you are somehow Better or Smarter because you paid more to have the "SE" color then you are mistaken.
one can easily change all the components and add the bumper and heel guards aftermarket or gytr and upgrade the shocks for the same cost and then not be stuck with a Burgandy red frame.
@@MrCuervoRacing facts Big Facts
I love the red frame
The grey is dull as fuck. Apart from that it's a nice bike
Sub'd
The first must buy is a dirt bike
Grew up on nothing but dirtbikes. First time I didn't have to put my feet down or lean the bike against something I fell in love. 2019 Raptor 700R.
☝🏻☝🏻☝🏻☝🏻😏
I've owned several raptor 660 and all were junk. If they have not fixed their design for the 700 then there is no way in hell i will own one of these pieces of shit.
#1 a better quad
And watch the shitty factory rear tires the sidewalls will fold up on you and roll your 700. I warned you
Aluminum is better then that shit plastic
Fast machines 500r energy absorption is why poly is used
Fast machines 500r autism
New ones are garbage 2010 se was perfect
I’m mad u called it a bike I’m so pissed dislike from me 👋🏽
Dumb...