For real? The important fit parts are not shown, your gloves and the words on the screen are in the way. I cant see what you're doing when you install the brake switch or control switches
Hello, I have a question, where is the small copper piece placed? I installed everything and it works but I couldn't install that small copper piece because I don't know where it has to be inserted. Could you help me please? Thank you.
@@psycho-cycler thanks for coming back at me. When I changed my handlebars I put them back together again and did not use any glue. Actually it really didn't need any glue I think I pushed it all the way on but it is on and it's not going nowhere. So thank you very much for the information. Live long and prosper.🦊
@motorpsycho2989 all good i figured it out, its actually a brass wedge that goes between the front break switch and inner housing of the switch block 👍
@danielfransson9380 no sorry i dont but if you put the brake switch in first and and push the switch towards the flat part on the brake lever there will be the smallest little gap between the back side of the brake switch and the housing. It slides in there. Does that make sence at all 🤔 i wish i did do a video of it as I've had heaps of people ask me about it now but once i finally figured it out I got the sucker in there. I could probably grab the old swich block and out and point out were it goes if that helps at all ??
So i mean yea, like you did the process. But i might as well been leaning over someone's shoulder n just watching. ** Also prob shouldn't wait til your on the second switch cover to THEN tell people to make sure they've removed the main fuse. But you failed to mention all the tedious steps IE: and which way to reinstall the break button wedge. Or the fact you need to hold onto your brass connectors that go over the throttle n idle cables, unless they bought new ones. Ok im done.
This video is about useless. Show what you're putting back in and where. Like dealing with the clips on the throttle cable to hold them in the housing.
0:32 Clutch lever replacement
1:23 Brake lever replacement
1:52 Right switch housing & grip removal
3:01 Right switch housing & grip installation
4:35 Left switch housing & grip removal
5:40 Left switch housing & grip installation
6:51 Old & new comparison
6:58 Regulator cover
Nice work. I'm considering installing the same for my 09 RK. Full-watch. 👍🏽🤠 4/7/23
For real? The important fit parts are not shown, your gloves and the words on the screen are in the way. I cant see what you're doing when you install the brake switch or control switches
Hello, I have a question, where is the small copper piece placed? I installed everything and it works but I couldn't install that small copper piece because I don't know where it has to be inserted. Could you help me please? Thank you.
Ohey, I have those Bezels on my fat boy's front lights too. They look awesome when riding and off the bike.
Awesome!
What was the stuff that you squeezed on The Handlebar before you installed the grip. Was it glue? And how much glue does it take?
Yes, it’s glue. Not so much is needed since the genuine HD accessories are all nice snug fit.
@@psycho-cycler thanks for coming back at me. When I changed my handlebars I put them back together again and did not use any glue. Actually it really didn't need any glue I think I pushed it all the way on but it is on and it's not going nowhere. So thank you very much for the information. Live long and prosper.🦊
Do you have a close up of the brass piece that goes were the frint brake switch is. Mine fell out and now have no brake light😮
Sorry, I don’t.
@motorpsycho2989 all good i figured it out, its actually a brass wedge that goes between the front break switch and inner housing of the switch block 👍
@@lnsdetailingmechanical5440 mine fell out too. don't know where it should sit! Do you have a picture or video of where it should be?
@danielfransson9380 no sorry i dont but if you put the brake switch in first and and push the switch towards the flat part on the brake lever there will be the smallest little gap between the back side of the brake switch and the housing. It slides in there. Does that make sence at all 🤔 i wish i did do a video of it as I've had heaps of people ask me about it now but once i finally figured it out I got the sucker in there. I could probably grab the old swich block and out and point out were it goes if that helps at all ??
To put my chrome housing on is there any sodering done?
No soldering necessary.
So i mean yea, like you did the process. But i might as well been leaning over someone's shoulder n just watching.
** Also prob shouldn't wait til your on the second switch cover to THEN tell people to make sure they've removed the main fuse.
But you failed to mention all the tedious steps
IE: and which way to reinstall the break button wedge.
Or the fact you need to hold onto your brass connectors that go over the throttle n idle cables, unless they bought new ones. Ok im done.
This video is about useless. Show what you're putting back in and where. Like dealing with the clips on the throttle cable to hold them in the housing.
Hello
How yo keep the switch from sliding around