Woodturning. Making money using just Carbide Chisels.

This will sell well and made only with Carbide tools.
To buy any of my Carbide tools or cutters visit my website;
www.ukwoodcraftandcarbidechisels.co.uk
www.buymeacoff...
Thanks for watching.
#Axminster 1628 lathe.
#wood
#woodturning
#carbide chisels
#Pine
Please Note;
These videos are meant for the purposes of entertainment. Any attempt to imitate or copy what I do must be done at your own risk. My practices may not always be correct or the safest for you. I strongly recommend that you find your own way of turning. You are responsible for your own safety while woodworking. Read and understand the operation and safety manuals supplied with your tools and machinery to ensure you are safe while using such equipment.

[@markduggan3451]

I had some of that pine from the "donate box" at my local B&Q and have found it turns very well.

[@glennteagleofukwoodcraftca5308]

Nice one. Happy turning.

[@Blitz-yn4kf]

It is finger tear out Glenn (thats the excuse I use )

[@alangibb3100]

Glenn & Liza What a great wee bud vase project it turned out smashing for pine. And I have been using YOUR carbide tool a lot lately and am starting to get very used to them, great job well done.

[@glennteagleofukwoodcraftca5308]

Thanks Alan. Glad you are enjoying using your carbide. Happy turning mate.

[@davidrobertson1344]

Watching the shavings when you were using the round, just like what I would expect from a skew. Very nice

[@glennteagleofukwoodcraftca5308]

Thanks David. Glad you enjoyed it.

[@indianatone218]

Nice job from a bit of tat .thanks for showing us .

[@glennteagleofukwoodcraftca5308]

Welcome to the channel Indiana. Glad you liked it. Toodle pip for now. Glenn & Liza

[@davidrobertson1344]

Pine is really attractive.

[@glennteagleofukwoodcraftca5308]

It can be. Has some lovely grain patterns.

[@perrys5954]

I love that center thing you put in the 4 jaw chuck before you have a tennon cut. such a quick change out! Please please does anyone know what it is called? I have a drive spur which is great for starting but its a lot of fiddling threading it off the lathe then mounting the 4 jaw chick. My 4-jaw looks just like the one in the vid so really really wanna find/get that removable spur thing. Oh and thanks for the great video Glenn I feel like I learning so much from you!!

[@glennteagleofukwoodcraftca5308]

This is what it is called on their Ebay site: WOODTURNING DRIVE CENTRE SET 3/4" X 16 TPI INTERCHANGEABLE DRIVE HEADS RDGTOOLS or just go to RDG Tools.

[@perrys5954]

@@glennteagleofukwoodcraftca5308 Wow thanks so much for such a clear and precise answer! I appreciate you! As a new subscriber I can't wait to catch up on so many great videos you have on your channel!

[@glennteagleofukwoodcraftca5308]

@@perrys5954 There are plenty for you to watch. Thank you for subscribing. Very much appreciated. Happy turning.

[@michaelwillson6847]

Cracking little bud vase m8 i do allot of work with live edge and pallets actually just dismantled couple large ones the other day and had some nice square maybe 5 inch by 5inch by 5 inch may need try something with them. Also would you be open to me sending you couple nice bits of wood to demonstrate something nice with 🏴󠁧󠁢󠁳󠁣󠁴󠁿👍

[@glennteagleofukwoodcraftca5308]

Hi Michael, that sounds great. Thank you very much. Much appreciated. Email me for details. [e-mail]

[@michaelwillson6847]

@@glennteagleofukwoodcraftca5308 will do I'll drop you email some point today and catch up about it. God some what I think is bog oak/elm mahogany and some spalted beech I'll send down. 🏴󠁧󠁢󠁳󠁣󠁴󠁿👍

[@glennteagleofukwoodcraftca5308]

@@michaelwillson6847 All donations appreciated.

[@glennteagleofukwoodcraftca5308]

@@michaelwillson6847 All donation to the channel are greatly appreciated. Thank you.

[@fergusrb]

Do you know a catch is good for old people? It makes the hart race, the adrenaline pumping, improves the reflexes as you duck real quick, but the only down side is some times you have to go in the house to change your pants.

[@glennteagleofukwoodcraftca5308]

Bad catches, not so good. It wasn't a catch I got on the last turning though that threw the pot off, it was because I had made a dovetail in the wooden chuck for something else I had turned, forgot about it and didn't do one on that piece. Thought it was funny though. Did say that they were selling fast, so fast that they are actually flying out of the door. Lol.

[@Hienwoodcarving]

❤❤❤❤❤

[@glennteagleofukwoodcraftca5308]

Glad you enjoyed it.

[@markb8954]

Too bad your audio is so muffled, it really makes listening difficult. My problem is how many bud vases can one make & give away, let alone sell.

[@glennteagleofukwoodcraftca5308]

It's my power cap faceshield that makes my voice sound a bit muffled. Nothing I can do about that I'm afraid. I will not turn without it on. When you do production turning, time is money. I would not be turning as slow as on these videos if I was in production mode, as explained in previous videos. Doing these videos is purely to help others. Make and sell/give away as many as you can.

[@markb8954]

@@glennteagleofukwoodcraftca5308 Thanks. Maybe you can squeeze a mic up inside the shield?

[@glennteagleofukwoodcraftca5308]

@@markb8954 We tried wireless mics a while back, but they cut out and we didn't know. Inside the shield, the power cap is really noisy. I like to give instruction as I go along. Most would stop and talk. Then the videos would be too long. If I fast forward or cut, then people complain as they don't like it. We just put the videos out now. If you watch it, you watch it. If you don't, you don't. There is no one else showing how to use carbides like I m using them. You learn something in every video. I don't like to have wires hanging whilst turning. Safety first.