Toyota 2ZR-FE PCV valve replacement
ฝัง
- เผยแพร่เมื่อ 7 ก.ย. 2024
- A walkthrough of how to access and replace the PCV valve on the 2ZR-FE 1.8L engine. You'll need the following components:
-Toyota PCV valve, 12204-37010
-22mm deep socket; 12mm and 10mm sockets also
-torque wrench
PCV torque: 15 ft-lbs
Bolts and nuts torque: 21 ft-lbs
no wonder I couldn’t find that #?!! thing! Hidden away like a buried treasure. Thanks for the map!
Thank you very much, you saved me a whole lot of time... 10 minutes to watch your video, 10 minutes to set game plan and 30 minutes to do job complete and test drive...
Benifits of changing pcv valve will it stop oil burning of 2zr fe?
I learned long ago to remove plastic dipsticks and set them safely aside before doing any serious work in their vicinity ... it only took one (or maybe two) broken ones to teach me that simple but valuable lesson.
Yup. Removing the dipstick aids in this process
Thanks. Spent 30 minutes looking for the damn thing. I was beginning think it was made obsolete. Just did an 04 and it was easy peasy. I guess some Toyota engineer wanted to add a challenge
Thanks for this, this video saved me a LOT of money, I was about to go in to a garage to have this done because I could not find the location of the PCV.
2008- 2009
I used a 7/8 box wrench for the valve removal...smaller than having to use a 22mm deep-well socket and ratchet plus it has an angled head...and I didn't twist over the intake as much. Thanks for this video.
Shit!!!! I could not find the PCV valve... Thanks a million for this video!
Thanks, your vid helped a ton! FYI a 7/8 deepwell will work too. 7/8" = 22.2mm.
Job went good. If your car is older or higher mileage, spray fasteners with WD40 or PB blaster first. Also re-tighted intake fasteners evenly a little bit at a time in a rotating pattern. Having a good assortment of socket extensions and swivel/universal joints helps too!
FYI if you do this I would suggest replacing the intake gasket, it orange rubber but if the tabs that stick out at the ends are black it's going bad and it may give codes especially in cold weather.
Thanks for this video. Replaced the PCV in my 2010 Corolla today.
The hardest part was getting that bolt in the lower right corner of the manifold. What was Toyota thinking with the placement of the valve? 😂
Benifits of changing pcv valve? Will it stop burning oil?
@@junaidkurd5034 Preventative maintenance to prevent pressure buildup from busting oil seals and causing oil leakages.
Thanks for the video. Those coolant hoses on the Throttle keep it from icing over and sticking when cold dense air rushes into it in very cold weather.
This is why Corolla has bad performance. It sends warm air into intake.
@@theodorekell so then bypass it....
@@theodorekell Almost all modern engines use coolant to heat the throttle body to keep it from freezing... It's standard practice everywhere. It doesn't impact performance. The amount of heat it transfers to incoming air is absolutely insignificant. Cold air intakes are extremely overhyped and air charge cooling only becomes a serious concern with forced induction.
@@mannys9130 Thanks anyway. But my Corolla comment was just Corolla/performance pun
Thank you sir no one covers this year engine everyone does 08 and older
Thanks for the video it really helped but not on my back lol it took awhile my brother has a 03 and it's on top of the valve cover it took 2 seconds and done but not on my 13😢
Thanks for the video, it is very informative.
Yes there is an intake gasket, and no I didn't mention it for this video. It's pretty easy to change out though.
Is it the same location on al 2zr fe engins including the toyota yaris 1.8 sr...hrlphelphelp
Thank you for video, i want to mention that thier is a 12mm bollt on left down side, behind genrator
Thanks for the part number
Very informative thank you
FYI, this is also possible on Toyota Avensia T27 2zr-fae, but it is realy difficult because of 2 bolts holding air intake, one close to generator and one close to valve body water piping. Also extreme difficult because of wiring between starter and manifold. You need to take out engine cover from below to access wiring clamp
Just did this today on a T27, there's an extra bolt on the left bottom of the inlet manifold. I had to remove the alternator to get to it. I see what you mean about the wiring behind the starter motor, I was able to get my hands in from underneath and cut the tie off, proper pain it was.
@@big_rideryou dont rely have to remove the alternator to get to tht bolt. jus use 2 small extentions
@@rommell9666 yeah I did try that but struggled to get it off, so in the end unbolted the alternator. It made it much easier.
I have same engine. I did everything exactly. But manifold did not go out from the place. Seems down on the left side something holding it. My hand can not reach or see what is attached, so i had to put everything back. At least cleaned throttle body :) and Fuel Rail valve regulator. I even couldn't see bolt around generator. Really shit motor of toyota. Auris much more easier
Thanks for your excelent video.
Thanks you!! I have a question, What is the frequency for change this Valve PCV?
I just changed my PCV valve and I noticed 2 issues that I didn't see covered in the video. My engine had one more hose located at the top of the manifold to disconnect and the wire loom on the right side and underneath on the right side of the manifold connected to the same cable were a big problem, another poor design. They took me the longest of anything to get disconnected. After pulling up the manifold and inspecting them they looked redundant. I also noticed when loosening the bolts on the manifold they were torqued way higher than specified, they were installed at the factory. I thought I was going to need a breaker bar to loosen them. The PCV valve was stiff to back out and stiff to re-install. Good luck on your PCV valve change, they appear not all to be the same.
muchas gracias bien explicado a pesar de no entiendo inglés pero entendí bien saludos desde Perú
I'm looking to purchase a used Corolla soon.This video made me want to avoid this engine,because I clean my PCV valve once or twice a year.
Love the video brother, thank you!! However, is there a gasket that needs to be replaced?
Good to replace intake gasket at same time
You can plug the coolant hose with something the right size
Make them difficult to replace so that the dealers will make more money. What's new.
Hi, great video. My Corolla has the same engine. When you disconnect the intake manifold, do you have to put new gaskets on? Also, before going to all the trouble to replace the PCV valve, is there any way to diagnose that it's faulty? Cheers, Jim Sydney, Australia
Thank you
What was the symptoms of failure? Mines doesn’t have a code but it showing some symptoms like stalling when idling for a while. This happens when AC is off and headlights off.
After you remove the intake manifold, I can see the openings. What can you spray in there to clean it?
Thanks I have a Toyota Yaris 2010 imported.from Japan nd have this motor.
Thank you for the video!!!
Nice, thanks for doing this. I hope I never have to change this on my 09 Vibe. Am I correct that there is no intake manifold gasket or did you just not mention/change it?
unfortunately PCV location for corolla.
Holyshit just skip to the 2:20 timer
LOL Why?
The real content is 2:30 into the video...
I have same engine. I did everything exactly. But manifold did not go out from the place. Seems down on the left side something holding it. My hand can not reach or see what is attached, so i had to put everything back. At least cleaned throttle body :)
Do you have to replace the intake manifold gasket????
Thats insane, such a complicated place to put it, geez
toyota wants me to pay 238 to change this bullshit? LOL shitty placement but easy to do
avin
I am thinking if we remove the intake and use an extension with a deep socket, will that be enough to get to the pcv? If so, will save a whole lot of disassembling.
You can't reattach the hose to the valve when you're done.
anyone know where its located on avensis t27 d4d 2010?
Should the gasket be changed?
If I know this earlier I would not buy this car! In addition to the removal of transmission fluid dipstick!
would this apply to my 2010 Scion XD AT? one online manual write up, requires discharging the fuel system along with draining the coolant. my coolant bypass lines into the throttlebody are 90deg hardlines into the hose.
Thanks for the video, very helpful! Have u seen the PCV valve location on The Camry, OMG! Any chance you’ve come across that model? Would love to see a video
great video. does this model have a egr valve?
I love my Toyota Corolla but what in the world were they thinking when they decided to put the valve in that area
thanks but what the need for changing this valve? whats the work of PCV valve? and when we should change it?
What causes the 2ZR engine rev to be unstable? (RPM goes up and down when i am pressing the vehicle on an open stretch of road)
Oxygen sensor clean it and check your car coals and plugs too
Did you says 21ft lbs on those 12 bolts & nuts?
i think this applies to camry 2011 surely
Hi I have same car do you know where the fuel filter is located? I know there is one in the fuel tank but is there another one located in the engine bay? Thanks
The Muffin Man it’s apart of the fuel pump assembly you would have the change the whole thing you can’t just change fuel filter, sucks because assembly is like 500$
Hello I am looking for a pcv valve for motor 1,4 d4d 2007
This engine is available in a Yaris. Must be fucking fun to work on.
no enginearing there what so ever
I wish TH-cam would force uploaders to watch their own videos.1:37 in and nothing of any use so far. Don't be afraid to edit your videos. Lol.
Wtf Toyota these used to be right on the side of engine
what is the reason to change PCV valve what the issue?
If it fails it can cause Oil leaks or a vacuum leak.
my XD started burning above avg oil amounts. The pressure in the engine will unseat the oil dipstick occassionally. And my oil press. switch started to weep oil. Im about to make this repair today.
Watch another youtube foot pounds of torque was not 21 on the bolts but 28 so much you also just explained instead of demonstrated by actually doing i believe is very important for me to see not just explain verbally
Terrible design
Mannnn toyota is being selfish now! 😡😡😡😡 on my 2007 corolla everything is easy even the transmission fluid easy to check and change but Now i have 2016 corolla s plus everything is pain in the butt!
I'm so done with Toyota ! Taking apart half of the motor to change a pcv valve
Lol
Yep, me too. In a couple years my 2017 Toy Corolla SE with a 6-speed manual transmission is paid off, I want to sell it and buy a 1988 Pontiac Fiero GT 5-speed. I can replace everything on the engine myself for very little money, insurance would be next to nothing, and it is a fine looking car. And no stupid Push-to Start button.