Please tell me the other remaining numbers on the L series and their functions. You have explained 1,5,3,11 then please explain others to and their functions 🙏🙏🙏. I love your teaching
Thank you so much for your effort Could you please tell me what is the toolkit required to establish communication between pc and electronic governor knowing that I already have L-series software
how to find minimum position and fail direction for engines. Trying to program lg2 speed controller but the engine runs perfectly but when we shut down, it runs for a minute or two after
hi, i have an l series on a v8 engine, the problem is that it runs haphazardly. it never stabilizes. works in 50hz, The question is. How do I connect it to the computer? to verify the stability and gain parameters, I have the program and the cable com. I have the installation manual. I connect it as it says there but I can't communicate with the PC. it will be that you can help me. Thank you
@@benzblogsVlogs the actuator is a woosward. p/n 8404-4005 I have the software. Woodward L-Series Service tool rev. R version 3.0.9112.0 and I also have the cable. the connection i used is pin 1 + pin 5- pin 3 gnd pin 4 tx pin 5 rx and it does not give me communication with the pc
@@waldolisandrograizaro7810 nonof you have the software for this thin there you can calebrate for the gain and stabilty till me if you are connected to your software so we can apply the value for this okay
ok sir, where to set the digital input adjust RPM because my machine has a problem, when I increase it to 1500 RPM on the digital input selector spring on the panel, the RPM slowly drops back down to 1300 RPM, where is the problem sir?, thanks
@@michaelangelomalonzo8653 sir kong my speed controller pwedi k mg adjust ng speed pwro kong electronic engine kailangan mo ng diagnostic tool to adjaut
@@benzblogsVlogs sir automatically naba ma access natin yung program sa modules na nka belt in na from manufacturing kadalasan kse sa genset nmin hirap mg start up unstable supply sa actuator.
@@funkyallabe3316 nasa kaba ngayun sir kong hirap mag start up maraming dahilan yan sir ither naubusan ng fuel,hinangin,or kolang sa startup fueling ither my problima ang fuel sonleniod etc marami pwedi kc sir dependi rin sa area
Sir may tanong lang ako regarding the load bank pareho lang ang ginagamit natin na load bank avtron, ano ang oroblema pag yung toggle switch ay ini on ko yung 2 hiling toggle switch pero nag aanbalance ang load ano kaya ang problema ng load bank namin minsan shutdown siya
Meaning ither 1-2-3 heating coil na my problima nyan sir potol na ang lenya double check mo lang din sir if kong gomana ang contactore nya all line 1-2-3
So ganito if electronic engine yan mgkakaroon lamg sya ng communication between ecm ang dule trough can buss just connect it thin select what is the correct type of ecm fitted in your egine and config.it in the module there is a selection there for the types of emgine pls subscribe there is vedios there you watch thank you
hi benz. May tanong ako tungkol sa Lseries. Mayroon akong isang 60hz 1800rpm generator na gumagamit ng lseries. Mayroon akong 2 katanungan; 1. Ano ang aktwal na bilis ng fuel pump na kinakailangan bago namin ikonekta ang koneksyon sa Lseries? Ang Lseries ay nakatakda sa 1800, kailangan ba ng mas maraming bilis ng engine kaysa sa lseries? 2. ano ang problema kapag ikinonekta ko ang koneksyon sa lseries, ang bilis ay nagpapanatili lamang sa 1800 nang mas mababa sa isang minuto at pagkatapos ay nagsisimula itong tumaas nang dahan-dahan nang hindi humihinto.
Sir kong ang engine enjection pump mo ay 1500-1800 convertable no problem mo pwedi mo ilagay yan magkakaroon kalang ng problima nyan if yung magnitoc picup mo ay di gumana at kailanagn mo din nag configuration nyan baho gumana
@@benzblogsVlogs oo Benz, ang ginagamit kong generator ay gumagamit na ng lseries. mayroon lamang ilang mga isyu na nauugnay sa bilis. kung ikonekta ko ang socket ng lseries sa lseries, ang bilis ay unti-unting tataas mula 1800 hanggang 2000. ang magnetikong pickup ay nagbago din kamakailan. nasilbihan na rin ang fuel pump. o ang magnetic pickup ay may negatibong positibo?
Beware not wearing complete ppe during taken video and posting TH-cam. That can use your opponent to report in HSE department. Unsafe act and be reflect to your company. Just saying
Benz, you are doing a great service to those interested. Keep educating. Technical Education is a must for the youngsters.
Thank you and bless you have a great day ahead🥰
Good day sir, maganda para Sa mga beginner para matuto ng troubleshooting . Galing mo talaga sir.
Sir salmat po sa pgtitiwala
Mastar Benz video is no 1 kindly keep the background low next time it's difficult to hear ur sweet voice
Its ok sorry
ayos! tuloy lang benz.. good luck!
Salamat wyn bless always ingat palagi
Thank you sir may natutunan n nman about mpu..
Welcome sir
You are real hero
Please tell me the other remaining numbers on the L series and their functions. You have explained 1,5,3,11 then please explain others to and their functions 🙏🙏🙏. I love your teaching
1-5 is voltage supply 12-24vdc 1+ 5- 3-11 is mpu
Thank you so much for your effort
Could you please tell me what is the toolkit required to establish communication between pc and electronic governor knowing that I already have L-series software
Lseries adpater wire
Goodwork sir benz..
Thank you sir
Great job!
But what about the shield cable? Shouldn't it be grounded from one side?
No need sir
Juat connect the red and the black cable in correct number it hundred percent work
keep it up happy new year
Thanks rhod
nice share knowledge
Thanks sir blesa u
Sir Woodward L Series 8404-1001 tool kit. Price please. . How can l purchase.
Sir im not sure the pricess but you can check in the internet
Coming to the magnetic pick up side between 3 and 11 , which one is positive and negative
No deference the magnitic picup wire is no problem this ac 5v ither interchnace
bro this is three phase or single phase because in your module line to line is 240 and line to neutral is 120
but in your output is 3 phases
Yes
how to find minimum position and fail direction for engines.
Trying to program lg2 speed controller but the engine runs perfectly but when we shut down, it runs for a minute or two after
What engine your using and what kva?
hi, i have an l series on a v8 engine, the problem is that it runs haphazardly. it never stabilizes. works in 50hz,
The question is.
How do I connect it to the computer? to verify the stability and gain parameters,
I have the program and the cable com.
I have the installation manual. I connect it as it says there but I can't communicate with the PC.
it will be that you can help me. Thank you
L-series or heinzman pandaroz
You need the software for that in order to connect the computer
@@benzblogsVlogs
the actuator is a woosward. p/n 8404-4005
I have the software. Woodward L-Series Service tool rev. R version 3.0.9112.0
and I also have the cable.
the connection i used is
pin 1 +
pin 5-
pin 3 gnd
pin 4 tx
pin 5 rx
and it does not give me communication with the pc
@@waldolisandrograizaro7810 yea it is woodward you have the toolkit for this
@@waldolisandrograizaro7810 nonof you have the software for this thin there you can calebrate for the gain and stabilty till me if you are connected to your software so we can apply the value for this okay
sir, how do you reset the l series in software ?
Sir reset only can do the alrms if u want to remove juat connect your est toolkit thin find the reset to remove the alarms
ok sir, where to set the digital input adjust RPM because my machine has a problem, when I increase it to 1500 RPM on the digital input selector spring on the panel, the RPM slowly drops back down to 1300 RPM, where is the problem sir?, thanks
@@Izanzedarr make sure that the calibration is correct and the configuration must correct
Sir pag underspeed alarm??
Naandar naman mga 1minute biglang magshutdown??ano po kaya problema
Cummins 120kva
6bt engine
Check mo ang speed mo ano bayan 60 or 50hz
Pag 50 -1500rpm dapat pag 60 1800rpm dapat okay para di mag shut down
Naglalaro lang sa 800-900 rpm sir kaya nagsshutdown
1800rpm sya 60hz
Ano po kaya sir pwede kong gawin??
@@michaelangelomalonzo8653 sir kong my speed controller pwedi k mg adjust ng speed pwro kong electronic engine kailangan mo ng diagnostic tool to adjaut
Sir ask lng po ako pg mg configuration tayu need ba talaga sa loptap or sa module lng Kong mg loptap may software na bayan Ang modules naka bilt in
Yea sir para ma acces mo yung di maaces na dapat maconfig
Kolang kc pag sa module
@@benzblogsVlogs sir automatically naba ma access natin yung program sa modules na nka belt in na from manufacturing kadalasan kse sa genset nmin hirap mg start up unstable supply sa actuator.
@@funkyallabe3316 ues sir if you have the laptop to configure it
@@funkyallabe3316 nasa kaba ngayun sir kong hirap mag start up maraming dahilan yan sir ither naubusan ng fuel,hinangin,or kolang sa startup fueling ither my problima ang fuel sonleniod etc marami pwedi kc sir dependi rin sa area
Thanks for you
can you send my factory passwords Perkins
@@yassinalrasheed7002 please send me that password
Sir may tanong lang ako regarding the load bank pareho lang ang ginagamit natin na load bank avtron, ano ang oroblema pag yung toggle switch ay ini on ko yung 2 hiling toggle switch pero nag aanbalance ang load ano kaya ang problema ng load bank namin minsan shutdown siya
Ok sir ganito lang yan unbalance meance 3phase ang load mo tama
Meaning ither 1-2-3 heating coil na my problima nyan sir potol na ang lenya double check mo lang din sir if kong gomana ang contactore nya all line 1-2-3
@@benzblogsVlogs thank you God bless
Sir ask lang po,, pano naman po yung may engine interface mudule pano po wiring diagram and mga connection po nya,, salamat po
Sir electronic engine po ba ibigsabihin mo
Opo sir
So ganito if electronic engine yan mgkakaroon lamg sya ng communication between ecm ang dule trough can buss just connect it thin select what is the correct type of ecm fitted in your egine and config.it in the module there is a selection there for the types of emgine pls subscribe there is vedios there you watch thank you
👍😍
Why always this failler 3 time I replaced work good then proplem
Wich one sir lseries actuator?
The problem is nit in the lseries make sure you install properly the mpu and the avtuator itself ok
@@benzblogsVlogs after i put new one he worked for one mouth then the engine hunting RPM not stable
@@wasifali4983 hunting happen if you have water in fuel and and in proper config of lseries thin the magnitic pickup
sana eto na sagot sa poblema ng genset namin..thanks sir
N prob sir i welling to help if posible
Benz bro i have same jobs to you. Sir i want to this jobs aboard , please inform me. I want to do. This work with you in your shop..
Inshallah check this site www.jubailibros.com i hope there still hiring
hi benz. May tanong ako tungkol sa Lseries. Mayroon akong isang 60hz 1800rpm generator na gumagamit ng lseries. Mayroon akong 2 katanungan;
1. Ano ang aktwal na bilis ng fuel pump na kinakailangan bago namin ikonekta ang koneksyon sa Lseries? Ang Lseries ay nakatakda sa 1800, kailangan ba ng mas maraming bilis ng engine kaysa sa lseries?
2. ano ang problema kapag ikinonekta ko ang koneksyon sa lseries, ang bilis ay nagpapanatili lamang sa 1800 nang mas mababa sa isang minuto at pagkatapos ay nagsisimula itong tumaas nang dahan-dahan nang hindi humihinto.
Yes sir ano po ba yun
Sir kong ang engine enjection pump mo ay 1500-1800 convertable no problem mo pwedi mo ilagay yan magkakaroon kalang ng problima nyan if yung magnitoc picup mo ay di gumana at kailanagn mo din nag configuration nyan baho gumana
@@benzblogsVlogs oo Benz, ang ginagamit kong generator ay gumagamit na ng lseries. mayroon lamang ilang mga isyu na nauugnay sa bilis. kung ikonekta ko ang socket ng lseries sa lseries, ang bilis ay unti-unting tataas mula 1800 hanggang 2000. ang magnetikong pickup ay nagbago din kamakailan. nasilbihan na rin ang fuel pump. o ang magnetic pickup ay may negatibong positibo?
Beware not wearing complete ppe during taken video and posting TH-cam. That can use your opponent to report in HSE department. Unsafe act and be reflect to your company. Just saying
Hello
I have a 2880A016 rev cable.
5450-1033 adapter.
But still can't connect to lcg. Can you help
@@ramzanzainool5774 is this for LSERIES? You need 232 to usb converter to work in the computer
Yes this is the L series, i am able to communicate but the rpm maintain 1800rpm under the load.
does not maintain 1800 rpm under load