Hi everyone! I made a mistake with the injector wire at 4:00. In this video I said to tap into the green wire, which DIDN'T WORK. Instead, I spliced into the other wire. MSD Box is working properly now! Fuse tapper: www.amazon.com/Nilight-NI-FH02-Circuit-Adapter-Warranty/dp/B0742BZXC2
Great videos Donny👍 I have recently did the 3:09 rear swap. Your video was very helpful. I’m currently doing a ported 6.4 swap and have most of the supplies needed👍 thanks for the great information to reference
I have installed my followed all directions on this video. And I still get 0 reading on my msd. I tapped into the second wire and yet no reading. Just 0. Any tips ? Car starts and drives. Just mad is at 0
By far the best explanation of any TH-cam channel 👍. Like I asked in the last video. Do you recommend an email tune or a dyno tune? If the latter what’s the best way to find a shop knowledgeable on these engines? My upgrade list is as follows. 6.4 intake manifold and throttle body. 309 lsd. 100 shot wet plate nitrous system for sure. Probably a hellcat lower air box, headers, and maybe a free flowing cat back. You talked me out of the cam, I like the current drivability as it will be my daily driver. Any help advise from you or the knowledgeable comment section. Thanks again for the great video.
Sorry. It's just a mini fuse tapper. If you ask guy at auto parts store they'll know what youre talking about. www.amazon.com/Nilight-NI-FH02-Circuit-Adapter-Warranty/dp/B0742BZXC2
So I got the manifold on and did all the wiring, no check engine lights or anything and can definitely tell a tone difference. Only thing is the MSD box doesn't light up at all so I'm pretty sure its not working... tested all the connections and they're all good so I think I got a dead MSD box :(
Hey Donny, thanks for your videos I completed my manifold install because of you, one thing I need help with is how the SRV connector is locked on, mine wasn’t locked in because the tab was broken so I had to replace the connector and squeeze my hands in behind the motor to put it back on😂🤣 but I need a good explanation of how the connector is installed and Locked on the srv actuator 😂 because it still slides off. I pressed forward on the red slider tab to try to lock it in place but it won’t click in. I’m sucha noob please help
Can you tell me what else I need to buy besides the msd box and the cricket boss? Any other harness? Also how can I get a copy of the diagram? Thanks for your time
@@DonnySRT so I finally got my hands on an intake. The only question I have now are what two ground bolts did you use? I’m not very knowledgeable on circuitry or stuff like that. We’re they the ones close to the PCM and near the fuse box and ABS?
Hi everyone! I made a mistake with the injector wire at 4:00. In this video I said to tap into the green wire, which DIDN'T WORK. Instead, I spliced into the other wire. MSD Box is working properly now!
Fuse tapper: www.amazon.com/Nilight-NI-FH02-Circuit-Adapter-Warranty/dp/B0742BZXC2
Great videos Donny👍 I have recently did the 3:09 rear swap. Your video was very helpful. I’m currently doing a ported 6.4 swap and have most of the supplies needed👍 thanks for the great information to reference
I’m glad you found it helpful man! Thank you for the feedback
Thank you
Hi everyone I have a 2012 5.7 and I just bought a 6.4 intake manifold, it is possible to just plug and play the intake manifold?
So for that pink wire are you able to just crimp it into the crimp provided with the tapper instead of trying to shove the wire into the actual fuse
So for that mopar wiring 1-3 should all be orange wires since the purple is to thin to be a ground correct?
@DonnySRT After you trim the red power wire off the circuit boss can you use the scrap red wire as a ground wire for the circuit boss ?
Whats the setup on the msd
Been waiting so long for a video like this! Thank you bro, im sharing this EVERYWHERE!
Appreciate it bro! Hopefully you find it helpful
I have installed my followed all directions on this video. And I still get 0 reading on my msd. I tapped into the second wire and yet no reading. Just 0. Any tips ? Car starts and drives. Just mad is at 0
How can I get wiring diagram
By far the best explanation of any TH-cam channel 👍. Like I asked in the last video. Do you recommend an email tune or a dyno tune? If the latter what’s the best way to find a shop knowledgeable on these engines? My upgrade list is as follows. 6.4 intake manifold and throttle body. 309 lsd. 100 shot wet plate nitrous system for sure. Probably a hellcat lower air box, headers, and maybe a free flowing cat back. You talked me out of the cam, I like the current drivability as it will be my daily driver. Any help advise from you or the knowledgeable comment section. Thanks again for the great video.
Awesome video. Im currently in process of doing this mod myself. Already have manifold on just need to order wiring parts for the runners.
Thanks man! It's pretty straightforward with the wiring. Just make sure you have the actuator already installed!
Where is the part # and pinned comment for 1:15?
Sorry. It's just a mini fuse tapper. If you ask guy at auto parts store they'll know what youre talking about. www.amazon.com/Nilight-NI-FH02-Circuit-Adapter-Warranty/dp/B0742BZXC2
So I got the manifold on and did all the wiring, no check engine lights or anything and can definitely tell a tone difference. Only thing is the MSD box doesn't light up at all so I'm pretty sure its not working... tested all the connections and they're all good so I think I got a dead MSD box :(
I've heard about similar issues from a few people about having a dead MSD box
Every time I ground pin 2 it shuts everything else off is there anything I may be doing wrong ?
Where did you get the electrical plug to the SRV servo at the back of the intake?
Awesome 👍
Hey Donny, thanks for your videos I completed my manifold install because of you, one thing I need help with is how the SRV connector is locked on, mine wasn’t locked in because the tab was broken so I had to replace the connector and squeeze my hands in behind the motor to put it back on😂🤣 but I need a good explanation of how the connector is installed and Locked on the srv actuator 😂 because it still slides off. I pressed forward on the red slider tab to try to lock it in place but it won’t click in. I’m sucha noob please help
Could be how Installed the wires in the connector? Do the wires just push in to the slots of the connector?
Great video bro.. helped a lot. Have you seen anything on ways to do the swap with out the cirkit box?
Thanks. i've heard of some people doing it without but I chose to keep it because of existing documentation with it
Im actually gunna do this to my 06 rt charger wich is cam heads torque converter gears
Sounds like the car is gonna be a beast
Where is the online wire diagram? I don’t see it in the description
You're right. Im trying to find the best way to upload it. I will reply to you when I figure it out
@@DonnySRT did you get that figured out? I'm about to attempt this on my Durango
@@DonnySRT did u figure it out
Can you tell me what else I need to buy besides the msd box and the cricket boss? Any other harness? Also how can I get a copy of the diagram? Thanks for your time
Hey Bill, I made a playlist where I have videos that should answer all of your Qs. One video has links to every part I used
@@DonnySRT I appreciate the reply. I did find the other video explaining the parts. Awesome job on providing this build. Best video by far.
Thanks man. Hopefully it was helpful
How much more power do you think you will get with this mod ? Thanks for the video you cleared up a couple of things for me.
This mod is mostly a mid-range power adder. Some people have seen around 25 ft-lbs of torque and around 20 hp in the middle
So what wire off the msd box sends the signal to the actuator to go into short runner mode?
Hey boss I’m interested in doing this pretty soon where can I find the link to that diagram
mario johnson yea bro dm me on Instagram
@@DonnySRT I don't use Instagram, is there another way to get the diagram
You said you have to buy another plug. Where did you buy your plug I'm needing one
Which plug are you talking about
@@DonnySRT the plug at 1:45
@@punisherhemi6008 I made a video with the links to everything. it's a wiring harness repair set
any idea if this would work with a 2012 rt? not sure if the wiring or electronics are different
I don’t see why it wouldn’t. Works for people with the 13 and 14
DonnyR/T cool cool. def gonna be getting this soon then. digging your build too man. keep it up 🤙🏼
Thanks man. Let me know if you’ve got more questions
@@DonnySRT so I finally got my hands on an intake. The only question I have now are what two ground bolts did you use? I’m not very knowledgeable on circuitry or stuff like that. We’re they the ones close to the PCM and near the fuse box and ABS?
What did you do with your EGR tube
My motor doesn't have an EGR thingy at the front
Dont you have to cut the redwire in half
6:16
🔥🔥🏁👍