There's a 35 dollar digitizer on amazon so i'm going to clean up the gunk and the new one comes with adhesive applied. Thanks for the vid! I reached out to dodge and the technician said he's going to see how much a new "radio" costs so i'm sure i'll be doing this myself.
Had the same issues with my Chrysler 300 so I followed your instructions on how to replace and clean the screen. Everything worked perfectly fine now just took me 4 hours of cleaning. Thanks for the video.👍🏽 Saved me a lot of money.
Oh my gawd you’re a lifesaver!!! I’ve been trying so hard not to go to an audio tech and come out of pocket for them to fix my screen. So I’ve been rolling around with my screen beeping and pressing buttons on its own lol smh thank youuuuuuu Rose (my 2018 rt) is gone appreciate this
I did this and it doesn’t show anything now , there has to be something that glues the screen to the digitizer that is how it was originally so I am assuming has to be done now. I saw another person use clear gorilla tape and it worked for him but I am reluctant to do it but since it doesn’t work will it hurt anything
Well the digitizer should come with strips of double side tape on it Butt long story short the trim ring should secure the digitizer so it doesn’t move also it your screen is not visible anymore make sure that the main ribbon cable is locked into place securely
@@bj_from_the478 I did , not sure what’s wrong but now it’s just weird colors and I can press some buttons I just don’t know where they are and the music works just don’t see anything but weird blurry red and blue smudge marks etc. I thought that the screen had to be fused or glued to the lcd panel the way it comes from factory. I will check the cables again.
I did this job yesterday, I used 91% isopropyl alcohol and Gorilla tape...I also ordered a new screen. this job is not easy and my hat goes off to BJ..
Hello,quick question. I replaced the whole unit. I connected the ribbons & installed it without all the screws on the back to make surenit worked b4 i put it all together. Now i took itback out put all the screws in and its saying no signal found? What do youthink happened?
Just make sure you didn’t bend one of the pins on the back of the radio were the harness connect too give you power I’ve see people do it all the time 👍🏿
Did I miss something or you never showed the install for the new digitizer? Looks like you were cleaning glue from screen then have the unit already assembled
I super sorry I had too edit some parts because I had people walking up asking me a million ? I do apologize about that Butt too answer your ? Just peel the double side tape off and reinstall your ribbon cable and your good as gold
@@bj_from_the478 pardon but another question. Is it possible that the glue or whatever it is , might be incurred UV activated adhesive that the original production run didn’t cure? Respectfully
Just replaced the digitizer but unfortunately there are dark areas on the screen and not all area's are responding, have you experienced this issue? And do u have a link for the digitizer you've been using?
You don’t have too purchase a new radio just change the digitizer and you’ll be fine by the way the Movie Christine was a great movie back in the day 😁
Boss man I need some help wondering if you can give me some advice,,,I was having the same issue that you just fixed but none of my knobs don’t work,, ac controls don’t work,, any advice you can give me
I understand unfortunately all the 8.4 units use the amplified systems alpine Harmon kardon Boston acoustic and beats the 7” aren’t and it will pull in Butt you won’t have sound 👍🏿
First thing first they don’t ride the best pot holes will destroy them and you have too run small tires I don’t recommend them for daily driving I rarely drive mine and it’s mainly for show
@@bj_from_the478 thanks man. My screen got cracked from an impact and the touch screen/function is no longer working. I can see the different pages and settings, just can't touch/change anything.
Hey there I’m attempting to do this myself and I would greatly appreciate if you were able to help out with this how ever I am in Cali. I’m willing to working something out. Look forward to hearing from you !
Is that what causes the "ghost touching" problem? My radio touch screen in my 2017 Charger R/T randomly changes on its own like someone's touching the screen.
@@bj_from_the478 Yeah it sort of looks like the top half of the touch screen has a film or coating that is peeling or separating, like when something that's laminated starts coming apart.
I brought a replacement screen put it all together it didn’t work properly so I clean the one that I took off originally I used a magic eraser to get screen clean and clear put it all back together and boom works like new just clean all the glue off both screen use some double side tape and it might work for you like it did me no more ghosting try before you buy a replacement digitizer
That’s a great way too get it back too working Butt a lot of these vehicles I work on the screen looks bad and old the digitizer makes it look brand new thank for the info👍🏿
I just installed a new digitizer but the the touchscreen is not working? I double checked the ribbon connections, I used white double-sided Gorilla tape (didn't completely go around the screen just to make it easy in the future to remove). Any ideas/suggestions why the touchscreen is not work?
@@bj_from_the478 I removed the double side tape that came pre-installed on the digitizer and put some white Gorilla tape. I saw other videos and read online forums that the white double-sided Gorilla tape works best. I unplugged the negative cable on the battery hoping that would reset the stereo. Unless there's there's another way to reset the stereo, please advice.
Sorry it wasn’t done on purpose I had too edit some parts because I kept getting interrupted by customers Butt too answer your ? The digitizer comes with double sided tape on it and just reinstall the ribbon cable
For a digitizer that does not come with adhesive, what kind of adhesive is recommended? I have seen another video of this repair where Gorilla Mounting Tape (double sided) was used to adhere the digitizer to the screen, but I also see electronic repair tape online that is super thin and is used for replacing tablet and phone screens. The mounting tape is a lot thicker. Is there any benefit to one over the other?
@@westonbranchick1516 I ended up just buying a replacement screen. The thin electrical tape didn’t allow for a large enough air gap and caused numerous other failures (random touches, multiple touches, etc) but the thick mounting tape was too large and didn’t register touches. Not sure what I was doing wrong but I just ended up buying the replacement screen for like $300
My 2018 Dodge Durango has multi colored lines going from top to bottom, started with one, now there’s a bunch. The touchscreen works fine, will this fix that issue or do I need to replace something else?
Well that’s a 50-50 shot in the dark and I can’t say that wouldn’t work Butt a new screen looks better and if it doesn’t work you’ll have too pull it all apart again 🤔
Replaced digitizer. All functions work...except the display. As I randomly press on black screen all functions seem to work fine. Black screen so I can physically see anything.
Any suggestions? Only thing I can think of is to double check my ribbon placement being that I can literally touch and toggle buttons on the screen...just no display at this point
@@bj_from_the478 Troubleshoot: My ribbons seem to be seated properly and locked in. The 2 small notches on each side of the ribbons are definitely hooked and seated. Checked fuses also. Took them out and replaced after about 30 secs. Feels as if all the Glue is off the screen b4 I placed new digitizer. Should be because I spent 2 hours cleaning the dang thing. I bet I'll NEVER try something like this again. I Ruined my infotainment for the next 2weeks smh
Also when i was taking apart the cable that the back portion has a connection to came off does this mean anything I was able to snap it back on. This is the first cable you see on your video not the second one
Okay first thing go I too the settings and restore too factory default it that doesn’t work take it back out of the dash and unplug the unit make sure all the pins are straight you may have list one too the side
If none of that works do you recommend anything else if im not mistaken there are only 6 cables from the car to the unit. Thankyou for responding the video was great as well
What did you use to open the screen? In my Grand Cherokee im seeing weird spots in between the digitizer and the glass. Looks like mold spots and I want to clean it. My display works fine, though.
@@bj_from_the478 i figured out that if I go that deep, might as well replace the screen, but even with the mold spots it works and they arent noticeable with the screen on. They are visible if you flash a flashlight directly to the screen, so 🤷🏻♂️. For now it stays like that. Thanks for the tip and the video, though 😉
@@Kevin09210 I usually change them out for the dealerships when cars get traded in because when the screen and the interior looks good and new the vehicle looks a lot better and it looks like it’s been taken care off and they buy them 🤙🏽
@@bj_from_the478 could you please read my comment. Im not trying to rush you or anything I just want you to see them and your opinion on my situation. Thankyou for your time
@@Kevin09210 a quick point which may be of issue is the spot size. If they head towards 3/16 you might be in the early stages of digitizer delamination . The next phase will change the spots to more whitish and micro bubbly. And glitches may be crazy. Looking at your screen from a high angle and offset might show the space between the digitizer and screen and then the black spots may be more visible on the digitizer only. Hope this helps
This sounds stupid but during the process of doing this I tried to keep my screws and stuff together and misplaced them and didn’t realize til I recieved the new screen, by chance do you remember what sizes they were:/ the ones in the radio itself
i just finished cleaning mine and putting it back in my car but now it’s a black screen or a white screen and occasionally the screen turns on and works but no touch features work, is there any fix? thanks.
@@bj_from_the478 the problem was the blue cable with the brown tape not being plugged in, it was ziptired under either the inside and i never saw it to put it back in it’s very simple and easy!
Hey BJ where are you located ? I’d love to have this service done on my 2018 charger. It’s ghosting bad to the point I have to ride with the radio off.
@@bj_from_the478that’s what’s wrong with mine! Going to try to do this myself and just replace the screen. It’s just come away from the radio. It was going bad when I bought the thing at two years old. Boy was I taken! I paid cash!
@@bj_from_the478 la084x01-sl01 or SL02 is $300 to $450 depending where to order it from. Just trying to justify the savings and time. Video of the guy with lcd swap makes it look like 1, 2, 3 and done. Is my brother's truck and we need to fix the lcd. Thanks
I have a contract with the dodger dealership too fix there cars so there OEM Parts that are given too me per vehicle the ones on Amazon will work just aswell just read the reviews before you order it. The key too make this thing work correctly is too make sure you perfectly clean the screen and get all the glue off 👍🏿
Just so y’all know, the chip that’s located on the bezel, i broke mine and it didn’t break the digitizer or touch screen. I think it’s a thermometer for the automatic AC. Which that’s a horrible place to put it considering how hot the Uconnect screen gets.
@@bj_from_the478 I did this repair today actually, took out the unit, cleaned the glue off the touchscreen and digitizer then placed double sided tape in between the two on the black border around the digitizer. So far no ghost touching. Only costed me some goo gone spray and the tape. Used your video as inspiration as well.
@@_.kvng.ky_1081so what your saying is just take off the original digitizer clean up the LCD screen and just slap the new one on with no glue or adhesive ? If that’s the case why not just clean up the old digitizer and re-use it
@@americanpatriot8996 the new digitizer should come with the adhesive strips on the outer layer. if throwing the old one back on just use double sided clear gorilla tape. he has another video looks just like this showing him putting the same digitizer back on using gorilla tape on the putter layer
Sorry I had too edit because I had some customers outside talking loud and there choice of works weren’t good so I apologize about that if you need technical support you call always reach out too me 🙏
Sure butt your not going too want too use any thing like that on a lcd screen prime example spray wd40 on you Tv screen in your house and let me know the outcome you’ll be in Best Buy tomorrow buying a new TV 😁 just be careful because that lcd screen is very sensitive and you can damage the screen 👍🏿
I have new videos out about changing the lcd screen butt I made this video almost three years ago so the prices of the lcd has gone down tremendously 👍🏿
![Repair Your Dodge Uconnect 8.4 Touch Screen [ Digitizer Yourself ] Save Money 💰](http://i.ytimg.com/vi/wb3IgOoiLUw/mqdefault.jpg)
![Repair Your Dodge Uconnect 8.4 Touch Screen [ Digitizer Yourself ] Save Money 💰](/img/tr.png)
Please checkout my channel I have several updated videos in full detail with tons of helpful tips thanks for tuning in 🙏
did you put a new digitizer on and did you use glue or? that part must’ve got cut out
There's a 35 dollar digitizer on amazon so i'm going to clean up the gunk and the new one comes with adhesive applied. Thanks for the vid! I reached out to dodge and the technician said he's going to see how much a new "radio" costs so i'm sure i'll be doing this myself.
Did u do it how did it come out?
@@gtkid3289 waiting to get a quote from the dealership before I do
@@killswitchh I crack my screen and i can hear the beep when I touch ot
@Mrv1960 eh, I'd rather save 300 and remove some gunk
@Mrv1960 only time will tell. Worth it to me.
Had the same issues with my Chrysler 300 so I followed your instructions on how to replace and clean the screen. Everything worked perfectly fine now just took me 4 hours of cleaning. Thanks for the video.👍🏽 Saved me a lot of money.
Glad I could help 🤙🏽
I could’ve saved more time just getting a replacement screen and you could’ve had the job done in 15 minutes
Yea it’s bad in them 300s 🤦🏾♂️ do we have to replace the screen or just clean it ?
@@donariusragland6319 no you don’t need to replace your screen. Just be very careful cleaning it with goo gone
Oh my gawd you’re a lifesaver!!! I’ve been trying so hard not to go to an audio tech and come out of pocket for them to fix my screen. So I’ve been rolling around with my screen beeping and pressing buttons on its own lol smh thank youuuuuuu Rose (my 2018 rt) is gone appreciate this
Is there a glue or something that you need to use to get the new digitizer to stick to the screen ?
Well the digitizer comes with strips on it
I did this and it doesn’t show anything now , there has to be something that glues the screen to the digitizer that is how it was originally so I am assuming has to be done now. I saw another person use clear gorilla tape and it worked for him but I am reluctant to do it but since it doesn’t work will it hurt anything
Well the digitizer should come with strips of double side tape on it Butt long story short the trim ring should secure the digitizer so it doesn’t move also it your screen is not visible anymore make sure that the main ribbon cable is locked into place securely
@@bj_from_the478 I did , not sure what’s wrong but now it’s just weird colors and I can press some buttons I just don’t know where they are and the music works just don’t see anything but weird blurry red and blue smudge marks etc. I thought that the screen had to be fused or glued to the lcd panel the way it comes from factory. I will check the cables again.
I did this job yesterday, I used 91% isopropyl alcohol and Gorilla tape...I also ordered a new screen. this job is not easy and my hat goes off to BJ..
Thanks I greatly appreciated the comment and you tuning into my channel
@@bj_from_the478 Hi BJ, you have some killer skills, knowledge, and patience, keep up the good work.
Hello,quick question. I replaced the whole unit. I connected the ribbons & installed it without all the screws on the back to make surenit worked b4 i put it all together. Now i took itback out put all the screws in and its saying no signal found? What do youthink happened?
Just make sure you didn’t bend one of the pins on the back of the radio were the harness connect too give you power I’ve see people do it all the time 👍🏿
@BJ_From_The 478
Thanks. i will check that out.
@BJ_From_The 478 That wasn't the problem, so im back to square one.
Did I miss something or you never showed the install for the new digitizer? Looks like you were cleaning glue from screen then have the unit already assembled
Yes he never placed the digitizer back. I’ve seen people put a new adhesive like double sided tape in between the LCD and the old digitizer
I super sorry I had too edit some parts because I had people walking up asking me a million ? I do apologize about that Butt too answer your ? Just peel the double side tape off and reinstall your ribbon cable and your good as gold
Mannn we missed the main part we all wanted to see lol. I appreciate the video I truly do but everyone speaks about double sided tape to reinstall
Do you put double sided tape along the whole screen interior or just the edges???
I just did this for my 18 grand cherokee but I replaced the old digitizer instead of a new one and the strip disconnected. Any tips??
Did you put tape for a thermal break in place of the glue? Or did you put new glue in?
Is the glue electrically conductive? Have you any experience with Subaru legacy 2019 screens?
Haven’t had too fix that particular model butt I’m sure it can be done ✅
@@bj_from_the478 I believe it can be but thus far no one can source a new digitizer.
@@bj_from_the478 pardon but another question. Is it possible that the glue or whatever it is , might be incurred UV activated adhesive that the original production run didn’t cure?
Respectfully
What causes my radio to come on for like 5 mins n den go off .do I need to jus clean the screen first before purchase a new one
What digitizer do you recommend?
Pulled the black wire off accidentally. Any suggestions or am i screwed
Not necessarily I think it’s a ground wire strip the wire back and ether glue it back or use some tape I think you’ll be fine
Can the old digitzer be cleaned and put back on. 2016 mazda 6 they dont sell a replacement digitzer
Just replaced the digitizer but unfortunately there are dark areas on the screen and not all area's are responding, have you experienced this issue? And do u have a link for the digitizer you've been using?
Okay what type of cleaner did you use because that LCD screen is very sensitive too certain cleaners and it can leave blemishes on the unit
BJ! Is that what makes my Challenger act like Christine. She is possessed. Dodge said I need a whole new radio
You don’t have too purchase a new radio just change the digitizer and you’ll be fine by the way the Movie Christine was a great movie back in the day 😁
Yea they said 5g’s. They kept redirecting me and said I can only buy a full radio from them😂
Boss man I need some help wondering if you can give me some advice,,,I was having the same issue that you just fixed but none of my knobs don’t work,, ac controls don’t work,, any advice you can give me
What leqiud u use for remove gillu
Is it possible if i have a 8.4 Uconnect and need to replace the whole head unit. Can i simply go with a 7” to save money?
I understand unfortunately all the 8.4 units use the amplified systems alpine Harmon kardon Boston acoustic and beats the 7” aren’t and it will pull in Butt you won’t have sound 👍🏿
When I disconnect the negative battery do I only do the one under hood or both n the back as well before uninstalling the radio
Have uhad any problems running 24's at thinking about getting a pair pros and cons please
First thing first they don’t ride the best pot holes will destroy them and you have too run small tires I don’t recommend them for daily driving I rarely drive mine and it’s mainly for show
I’m doing this and when I pulled the screen out of the frame I pulled the wire out. Do you know where it goes and what it does?
that little wire from the black metal frame is a ground, which makes the touch screen work via electrical conductivity via your finger.
I broke mine and it still works
I wonder if this why my radio comes on for like 5 mins n den it goes off
What’s the link to get an OEM digitizer
What would use the razor for?
The razor was use too get between the digitizer and the lcd screen some I can start the removal process
What’s the screen part number since I’m replacing it since there a black dot on the screen on my buddy’s radio
If my screen is cracked and the touch function is no longer working do i need just the screen? Or the whole Digitizer?
Just the digitizer
@@bj_from_the478 thanks man. My screen got cracked from an impact and the touch screen/function is no longer working. I can see the different pages and settings, just can't touch/change anything.
@@matthewjacques392 glad I could help
Hey there I’m attempting to do this myself and I would greatly appreciate if you were able to help out with this how ever I am in Cali. I’m willing to working something out. Look forward to hearing from you !
Sure reach out too me when you start your journey and if you have any? Call me 478-262-9307 Monday -Saturday 10am-7pm eastern standard time 🙏👍🏿
@@bj_from_the478where are you located?
@ATROXCUSTOMS I’m located in Macon Georgia
Is that what causes the "ghost touching" problem? My radio touch screen in my 2017 Charger R/T randomly changes on its own like someone's touching the screen.
That your issue
@@bj_from_the478 Yeah it sort of looks like the top half of the touch screen has a film or coating that is peeling or separating, like when something that's laminated starts coming apart.
@@dwunnamillion its actually glue in between the two, the heat from the car and from the heat hitting the screen causes the delamination.
Same problem, same car! I got a 2017 Dodge Charger with the same problem
I brought a replacement screen put it all together it didn’t work properly so I clean the one that I took off originally I used a magic eraser to get screen clean and clear put it all back together and boom works like new just clean all the glue off both screen use some double side tape and it might work for you like it did me no more ghosting try before you buy a replacement digitizer
That’s a great way too get it back too working Butt a lot of these vehicles I work on the screen looks bad and old the digitizer makes it look brand new thank for the info👍🏿
So im having a issue where the touch doesnt work at all do yoy think this sort of repair could fix this issue
I just installed a new digitizer but the the touchscreen is not working? I double checked the ribbon connections, I used white double-sided Gorilla tape (didn't completely go around the screen just to make it easy in the future to remove). Any ideas/suggestions why the touchscreen is not work?
The digitizer should have came with double sided tape on it you probably have it too far away from the lcd
@@bj_from_the478 I removed the double side tape that came pre-installed on the digitizer and put some white Gorilla tape. I saw other videos and read online forums that the white double-sided Gorilla tape works best. I unplugged the negative cable on the battery hoping that would reset the stereo. Unless there's there's another way to reset the stereo, please advice.
do you have a link to the part?
Totally skipped installing the digitizer. Did your replacement have an adhesive strip or did you use something else? How thick?
Sorry it wasn’t done on purpose I had too edit some parts because I kept getting interrupted by customers Butt too answer your ? The digitizer comes with double sided tape on it and just reinstall the ribbon cable
@@bj_from_the478 Okay, mine did not come with double-sided tape. They said they no longer provide it (this Amazon dealer).
For a digitizer that does not come with adhesive, what kind of adhesive is recommended? I have seen another video of this repair where Gorilla Mounting Tape (double sided) was used to adhere the digitizer to the screen, but I also see electronic repair tape online that is super thin and is used for replacing tablet and phone screens. The mounting tape is a lot thicker. Is there any benefit to one over the other?
I also have this question.
@@westonbranchick1516 I ended up just buying a replacement screen. The thin electrical tape didn’t allow for a large enough air gap and caused numerous other failures (random touches, multiple touches, etc) but the thick mounting tape was too large and didn’t register touches. Not sure what I was doing wrong but I just ended up buying the replacement screen for like $300
Is it ok to use some of the cleaner to get the glue off of the ribbon cable at the bottom of the screen?
My 2018 Dodge Durango has multi colored lines going from top to bottom, started with one, now there’s a bunch. The touchscreen works fine, will this fix that issue or do I need to replace something else?
You need to replace the LCD
So if my screen is ghosting I basically need to take it apart and clean it throughly??
Well that’s a 50-50 shot in the dark and I can’t say that wouldn’t work Butt a new screen looks better and if it doesn’t work you’ll have too pull it all apart again 🤔
@@bj_from_the478 I actually watched your video top to bottom and took everything apart it was so much adhesive. Funny thing I fixed it last night
Just what I need thanks for the video
Dang I pulled mine off by accident....... any suggestions
Replaced digitizer. All functions work...except the display.
As I randomly press on black screen all functions seem to work fine. Black screen so I can physically see anything.
Okay was your reason for changing the digitizer was that the touch screen wasn’t working or was the screen black from the beginning
Changed because of ghost touching. Screen always worked and Screen was never black. Random ghost touches only
Any suggestions? Only thing I can think of is to double check my ribbon placement being that I can literally touch and toggle buttons on the screen...just no display at this point
@@hellyea939 just open it back up and make sure the ribbon cable is seated correctly
@@bj_from_the478 Troubleshoot: My ribbons seem to be seated properly and locked in. The 2 small notches on each side of the ribbons are definitely hooked and seated.
Checked fuses also. Took them out and replaced after about 30 secs.
Feels as if all the Glue is off the screen b4 I placed new digitizer. Should be because I spent 2 hours cleaning the dang thing.
I bet I'll NEVER try something like this again. I Ruined my infotainment for the next 2weeks smh
Hey just replaced my digitizer put everything back in the car how it was and now my bluetooth and car play connect but no sound any word of advice
Also when i was taking apart the cable that the back portion has a connection to came off does this mean anything I was able to snap it back on. This is the first cable you see on your video not the second one
Okay first thing go I too the settings and restore too factory default it that doesn’t work take it back out of the dash and unplug the unit make sure all the pins are straight you may have list one too the side
If none of that works do you recommend anything else if im not mistaken there are only 6 cables from the car to the unit. Thankyou for responding the video was great as well
Are these screws Phillip head screws? Or? Plan on doing this over the weekend
Yes they are
What did you use to open the screen? In my Grand Cherokee im seeing weird spots in between the digitizer and the glass. Looks like mold spots and I want to clean it. My display works fine, though.
I used a plastic tool and a razor
@@bj_from_the478 i figured out that if I go that deep, might as well replace the screen, but even with the mold spots it works and they arent noticeable with the screen on. They are visible if you flash a flashlight directly to the screen, so 🤷🏻♂️. For now it stays like that. Thanks for the tip and the video, though 😉
@@Kevin09210 I usually change them out for the dealerships when cars get traded in because when the screen and the interior looks good and new the vehicle looks a lot better and it looks like it’s been taken care off and they buy them 🤙🏽
@@bj_from_the478 could you please read my comment. Im not trying to rush you or anything I just want you to see them and your opinion on my situation. Thankyou for your time
@@Kevin09210 a quick point which may be of issue is the spot size. If they head towards 3/16 you might be in the early stages of digitizer delamination . The next phase will change the spots to more whitish and micro bubbly. And glitches may be crazy. Looking at your screen from a high angle and offset might show the space between the digitizer and screen and then the black spots may be more visible on the digitizer only. Hope this helps
Hey how Can k contact you to do my Dodge Charger Daytona . It have the same screen with does problems
478-262-9307 Monday-Friday 9 am-7pm 🙏
The Antenna wire came undone. Where do do I reconnect it to??
I accidentally took the ribbon gold thing off my screen. Do I need a new one?
I’m sorry you took off witch ribbon cable
This sounds stupid but during the process of doing this I tried to keep my screws and stuff together and misplaced them and didn’t realize til I recieved the new screen, by chance do you remember what sizes they were:/ the ones in the radio itself
I’m finding some replacements on Amazon with the option for LCD(more expensive) vs non LCD. What’s the difference and does it matter?
Replacing the digitizer is always cheaper than replacing the screen the digitizer is just the Touch panel the lcd is the screen like your TV
Thank you I appreciate the help!
Was there a specific brand or it doesn’t matter?
Hey bro I cleaned it and everything but the touch won’t work no more any way you can help me ??
Make sure the ribbon cable is secured properly
Were you able to get it working
Yes sir great video💪🏾💪🏾
Clean video brotha🤘🏾 great knowledgeable dialogue
I just used a blow dryer while the screen was sitting up right!
I tried this but couldn't get it to work. I had a guy tell me he was able to get most of the bubble out by just using a blow dryer?
i just finished cleaning mine and putting it back in my car but now it’s a black screen or a white screen and occasionally the screen turns on and works but no touch features work, is there any fix? thanks.
Okay can you give me a call 478-262-9307 it’s some questions I need too ask you
Same here wondering why is this happening after fix
@@wansmith7499 you may need too check the ribbon cable again too make sure it’s plugged in correctly
@@bj_from_the478 the problem was the blue cable with the brown tape not being plugged in, it was ziptired under either the inside and i never saw it to put it back in it’s very simple and easy!
Put mines back together now touch not responding at all..any ideas? Using same digitizer
My screen won’t let me select nothing do you have any tips what I did wrong
Sure let’s start did you change the digitizer
What state are you located ?
Georgia
Hey BJ where are you located ? I’d love to have this service done on my 2018 charger. It’s ghosting bad to the point I have to ride with the radio off.
I’m in Macon ga my number 478-262-9307
Color damage solution?
Sorry butt I’m not understanding your ? Does the lcd have some discoloration on it
Was your screen blank before u installed the screen? Or u still could see your controls on screen?
It wasn’t it actually worked and played fine some of the touch screen wouldn’t work it had a mind of its own
@@bj_from_the478that’s what’s wrong with mine! Going to try to do this myself and just replace the screen. It’s just come away from the radio. It was going bad when I bought the thing at two years old. Boy was I taken! I paid cash!
Bro saved my pockets 🙏🏽🙏🏽💯
Anytime 👍🏿
@@bj_from_the478478, do you live in Macon ga? How much will you charge to fix my daughter radio? I’m from south Ga
Why not just change the lcd? Less time consuming. $$$? Difference?
OEM screen is 1,300 if the customer wants too pay for a new screen I’ll change it
@@bj_from_the478 la084x01-sl01 or SL02 is $300 to $450 depending where to order it from. Just trying to justify the savings and time. Video of the guy with lcd swap makes it look like 1, 2, 3 and done.
Is my brother's truck and we need to fix the lcd. Thanks
Ebay has a lq084x5lx01 for $200. That s the lcd screen with touch screen assembly
Where can I order the digitizer?
Your local dealership or Amazon
How do I know if I order right o e off Amazon
Did you use glue it back together
Sorry no glue is used on the new digitizer it will come with some double sided tape 👍🏿
Hey BJ do you make custom subwoofer box? I got a 2022 Dodge Charger Widebody and i want a nice custom box for 2 12 inch Audiopipe txx bdc2 12
I sure do hit me up tomorrow 478-262-9307
Hello great video, what is the factory part number that you referenced?
I have a contract with the dodger dealership too fix there cars so there OEM Parts that are given too me per vehicle the ones on Amazon will work just aswell just read the reviews before you order it. The key too make this thing work correctly is too make sure you perfectly clean the screen and get all the glue off 👍🏿
@@bj_from_the478 thank you. I ordered mine today. Fingers crossed she goes back together well. :). Thanks again.
@@onevisiononegoalonegod744 well if you need some pointers hit my line 478-262-9307 I’ll help 🤙🏽
Just so y’all know, the chip that’s located on the bezel, i broke mine and it didn’t break the digitizer or touch screen. I think it’s a thermometer for the automatic AC. Which that’s a horrible place to put it considering how hot the Uconnect screen gets.
Sir you should be able too solder that wire back too the bezel
what is that, wifi connection? @@bj_from_the478
Anybody know a place I can take my durango to in dc md VA area to pay to get this done? I don't trust myself to do this lol.
hello BJ I’m from Los angles can you please help me to do it ?
Sure if you want me too fix it just ship me your radio and I’ll fix it
@@bj_from_the478 and how long it takes you to finish everything?
@@bj_from_the478 How much is gonna be ?
uconnect sucks this is a recall , worst company is one that doesnt fix or pay for a problem that is theirs ,
Or you could spend a little over 200 and have one shipped from China. That is an upgraded part number.
Where are u located bro?
Macon Ga
Ima just get a whole new radio I already want the Tesla screen anyways
Why not put the digitizer back on?
Because a bad digitizer looks awful old and dirty
Also I’m cleaning the glue off the screen no the digitizer
@@bj_from_the478 I did this repair today actually, took out the unit, cleaned the glue off the touchscreen and digitizer then placed double sided tape in between the two on the black border around the digitizer. So far no ghost touching. Only costed me some goo gone spray and the tape. Used your video as inspiration as well.
@@vapesan666 greatly appreciated thanks glad it helped
How thick double sided tape did you use on the black boarder
Great video
Thanks
What did you use in between the lcd and digitizer?
You don’t have too use anything just clean it properly and install the new digitizer and your good
@@bj_from_the478 thanks 👍🏾 do you have a link as well to the one you use, tried looking up the number in the description it didn’t show anything
@@_.kvng.ky_1081so what your saying is just take off the original digitizer clean up the LCD screen and just slap the new one on with no glue or adhesive ?
If that’s the case why not just clean up the old digitizer and re-use it
@@americanpatriot8996 the new digitizer should come with the adhesive strips on the outer layer. if throwing the old one back on just use double sided clear gorilla tape. he has another video looks just like this showing him putting the same digitizer back on using gorilla tape on the putter layer
U in Atlanta lol I need mine did
I’m in Macon Ga
Did you go to him ?
@@BunnySTL na I ended up getting a whole new one off Facebook market for 300
🔥🔥💯💯💯
Thanks dude wish me luck!
Let me know how it turns out
Turned out great! It took forever to get that glue off but awesome thanks again!
why you cut the part when you put the new one???
Sorry about that check my channel out I have some updated version videos that maybe helpful
I did this and it lasted almost a year now doing it all over again this time I'm just replacing the entire unit...
You didn’t show putting the replacement screen on
Sorry I had too edit because I had some customers outside talking loud and there choice of works weren’t good so I apologize about that if you need technical support you call always reach out too me 🙏
Thanks.. did you replace the outside touch or just clean it.🙈 my English not will
I replaced the outside glass touch screen
Couldn't you just clean the glue off the old screen and reuse it ?
You can try it Butt a new one looks better
WD40 works wonders for glue removal.
Sure butt your not going too want too use any thing like that on a lcd screen prime example spray wd40 on you Tv screen in your house and let me know the outcome you’ll be in Best Buy tomorrow buying a new TV 😁 just be careful because that lcd screen is very sensitive and you can damage the screen 👍🏿
@@bj_from_the478 Why would I spray WD40 on a perfect working TV?
Can I send mines and pay you to fix it lol.
You sure can
I just bought a new screen for 200 online lol.
How do it turn out
Great, far less effort than this haha.
@@angryitalian3430 that’s what up
What site ?
I was just easier and cheaper to install the whole screen. Paid $115 on EBay.
I have new videos out about changing the lcd screen butt I made this video almost three years ago so the prices of the lcd has gone down tremendously 👍🏿
@@bj_from_the478 you are right. Prices have gone way down on these. Dealer 2 years ago wanted $1500 to install a new oem stereo.
90% rubbing alcohol worked really well to
You missing details bro