Man I love the corvette body. I’m in the process of building a limitless speed run car. I thought I ordered that same body but it’s the 1/10 size 🤦🏻♂️. Gotta find the right C7 body.
Hey homie... The BEST way to trim the wheel wells is wrap a piece of sand paper around a spray can or bottle that fits inside the wheel well and twist and rotate with like 400 grit. can also adjust the diameter of the can or bottle by wrapping 2' tape around it to make it wider. its the best symmetry.
Thank you sir. Never will I lock my front and rear diffs. I'm running 500k front and rear. Think about it. If your road is slightly curved and your vehicle drifts slightly off track, there will be one tire that will break traction being they can't "differentiate" in speed to compensate movement. Therefore I would say it's the best if both worlds if you run a thicker viscosity fluid inside so you won't hurt from that. Running a locked diff depends on your road. Not your setup.
Hey man, love your videos. You mentioned as power goes up, amperage goes down.. if the inverse were to happen, like power and amperage continuing to climb, does that mean you can gear up?
Oh by the way great videos I’ve seen most of your videos you have great advice far as using the drill I didn’t know you can do that. I think go over the data more would be great information for most people to get a better understanding what it all means.
What are you using for your front suspension. I know it’s a link or toe link but what exactly are the specs? I’m curious and it’s a good idea to getting the ride height just right. I also like the idea of having it stiffer than fluid.
Awesome vid! I need to check my data logs for my monster Mojave. The spool should be here any day! I might have to hit you up w some advise since I’m doing this on 6s only.
Damm good video again , can u go more in depth on data log, one day, and how to gear up or down from it, lot of people dnt understand it , i know i dnt plz
So what body mounts are you using on this? And are these custom made pinion gears or are they readily available? I looked at a few other posts but didn’t see anything on both of these topics. Any help is greatly appreciated.
It is stock regarding the body mounts. It's an infraction so they are already there made out. The gears I ran you can buy from Sagacustoms.coms they have the highest quality gears.
@@InnovationRC Perfect thank you. I wasn’t sure since I’m running the limitless and the body mount is slightly different so I just figured I would doublecheck thank you. In the process of getting this ready for spring.
Yes long and hard I've thought. The only reason why I made a gt car is because delta came out with the c8 body.. I would further desire this body than the Toyota because everyone runs it for speed. I prefer a change if taste. Additionally it's pretty aerodynamic.
I swear to god sometimes you do things that i just did like the gold with black color. dont tell me red is in there someday. Lol.. On the cleaning part have you heard of honda polish? Its a spray can that uses dry wax to get in between dirt and surfaces. Honda designed it to collect dirt particles so that it can be removed using gravity. It is also a plastic and rubber lubricant and sealer it also makes water evaporate; I use it to clean my dirt bikes and quads(atv) it cleans and polish. It may not he legal in all states i have to buy mine and have it del to a local shop then i have to pick it up. Cheers
No red. What car do you have that's painted the same? That's too funny very ironic. I've been going with my channel theme color for the past year to match my other cars paint jobs
I would not to much cut from the body. special i can see on the front. If you was you cutting the body symetric this should not happen on only one side. That means, i would work on the dampers or maybe the chassis are not 100% in straight line. Interessting are also it is on front and back on the same side. Right? So i think you have to addust your dampers or chassis position.
Agreed, only cut from the side fender a little. But it is from the air pushing the body down. Bending the plastic body posts slightly. I will do something to reinforce the body to stay consistent at speed
Hello brother, it would be very helpful for us Latinos who follow you if you activate the subtitles in Spanish that would help you also have more subscribers
On PC, I think you can go to at the bottom of the video, on mobile find the 3 dots that will be settings: settings> subtitles> auto translate> language of preference.
If you haven't seen the FULL 141 Mph pass click the link here! 👇 th-cam.com/video/OK4zk6PBR9w/w-d-xo.html
Man I love the corvette body. I’m in the process of building a limitless speed run car. I thought I ordered that same body but it’s the 1/10 size 🤦🏻♂️. Gotta find the right C7 body.
Mann I love your channel, keep it going!
Great video, big thanks for sharing it😎👍
Sweet build and great tips. Good luck brother
Thanks Brother certainly appreciate that!
YOU KILLIN IT BROTHER!
Thanks badger!
Very informative video as always brother 🤟🏽
Appreciate that Kaycee!
yo B you knocked out the park with this informative video bro. Great job my brotha 👊👊💯💯👍👍
Glad you liked it thanks man
Thank you so much for making this very informative video!!
Love the videos bro big van
Good and very informative video bud 💪🏾💯
Thanks Coach!
It never ceases to amaze me how amazingly well you can handle that rc at those speeds, I have difficulty with my crawlers at their top speed lol 😂
I used to think the same way back when before I ever did speed!
Great video, specially how u inform us.
Glad you liked the video!
Ready for the "Hunaudières' straight"... 👍‼️💯🏁🏎️🤓
Yes thanks for the wing info! Brackets are on their way! Frankenstein
awesome setup and information
Thank you sir! Glad you found it helpful
@@InnovationRC 👍👊😃
Thanks for this interesting Video ✌💪
Hey homie... The BEST way to trim the wheel wells is wrap a piece of sand paper around a spray can or bottle that fits inside the wheel well and twist and rotate with like 400 grit. can also adjust the diameter of the can or bottle by wrapping 2' tape around it to make it wider. its the best symmetry.
You broke the world wreck world record for fastest rc car in the world
That's great piece of info right here :)
Thanks.
Q: 7:12 Do you have full locked diffs?
Thank you sir. Never will I lock my front and rear diffs. I'm running 500k front and rear.
Think about it. If your road is slightly curved and your vehicle drifts slightly off track, there will be one tire that will break traction being they can't "differentiate" in speed to compensate movement. Therefore I would say it's the best if both worlds if you run a thicker viscosity fluid inside so you won't hurt from that. Running a locked diff depends on your road. Not your setup.
Hey man, love your videos. You mentioned as power goes up, amperage goes down.. if the inverse were to happen, like power and amperage continuing to climb, does that mean you can gear up?
Voltage goes up, amperage goes down to get to the same place the lower voltage was at. Probably worded it wrong 😀
Oh by the way great videos I’ve seen most of your videos you have great advice far as using the drill I didn’t know you can do that. I think go over the data more would be great information for most people to get a better understanding what it all means.
Glad you found it useful Danny. I intend on making a better, updated video soon
What are you using for your front suspension. I know it’s a link or toe link but what exactly are the specs? I’m curious and it’s a good idea to getting the ride height just right. I also like the idea of having it stiffer than fluid.
I use tie rods. You just need to get rods that are adjustable around the same length as the shocks
For sure you will hit even higher speeds!😍. Why is there never a link to the tires in your description? 🤔
1/8 BSR foam tires, I ran pinks in back purples in front. I normally don't do links on everything I normally run! But if you ask you'll receive!
Awesome vid! I need to check my data logs for my monster Mojave. The spool should be here any day! I might have to hit you up w some advise since I’m doing this on 6s only.
Absolutely do so anytime. Message me on instagram I get those like texts
@@InnovationRC I don’t have ig lol. Are u on fb?
@@InnovationRC hey how do I get the speedo on the screen like that!? What do you use?
Damm good video again , can u go more in depth on data log, one day, and how to gear up or down from it, lot of people dnt understand it , i know i dnt plz
Can can certainly do it again, I do want to keep testing and eventually get a new PB, so I can confirm my information. We will see in the future
Simple Green will oxidize aluminum. Not sure if it corrodes it too .
Where did u get the body looks nice
Super informative Bro...Which Rear Spoiler is that?
Glad you found it helpful Junior, the rear wing is an outcast 8s wing! I stated it in the previous 141 Mph run video!
@@InnovationRC Respect Bro Nice numbers Keep Pushing
Hey 👋 what wing have you got on your gt build I also want one but don't which one will fit.
And your looks nice 👌
Thank you so much! It is an outcast 8s wing!
@@InnovationRC thanks I got the 8s wing but I have having trouble attaching it on my car but now I'm all sorted thanks 😊👍
So what body mounts are you using on this? And are these custom made pinion gears or are they readily available? I looked at a few other posts but didn’t see anything on both of these topics. Any help is greatly appreciated.
It is stock regarding the body mounts. It's an infraction so they are already there made out. The gears I ran you can buy from Sagacustoms.coms they have the highest quality gears.
@@InnovationRC Perfect thank you. I wasn’t sure since I’m running the limitless and the body mount is slightly different so I just figured I would doublecheck thank you. In the process of getting this ready for spring.
Yo what's up bro do u use turnbuckles for ur rear shocks
i have that same tee shirt!!
Awesome!
What fan mount and center brace is that? I’m looking for them now.. could help thanks
Could you link me to that motor mount please n thanks for the very imformitive video love the connent
Look up
Practicalprototypesolutions.com
appreciate that thanks man did you see the arrma 1\5 scale exb ... I Might need.... Bad.
Be funny to watch him race people with it
Have you thought about running a toyota gtone body for lower resistance?
Yes long and hard I've thought. The only reason why I made a gt car is because delta came out with the c8 body.. I would further desire this body than the Toyota because everyone runs it for speed. I prefer a change if taste. Additionally it's pretty aerodynamic.
What pinion/spur size are you using?
34 pinnon 42 stock center diff 8s
I swear to god sometimes you do things that i just did like the gold with black color. dont tell me red is in there someday. Lol..
On the cleaning part have you heard of honda polish? Its a spray can that uses dry wax to get in between dirt and surfaces. Honda designed it to collect dirt particles so that it can be removed using gravity. It is also a plastic and rubber lubricant and sealer it also makes water evaporate; I use it to clean my dirt bikes and quads(atv) it cleans and polish. It may not he legal in all states i have to buy mine and have it del to a local shop then i have to pick it up. Cheers
No red. What car do you have that's painted the same? That's too funny very ironic. I've been going with my channel theme color for the past year to match my other cars paint jobs
I would not to much cut from the body. special i can see on the front. If you was you cutting the body symetric this should not happen on only one side. That means, i would work on the dampers or maybe the chassis are not 100% in straight line.
Interessting are also it is on front and back on the same side. Right? So i think you have to addust your dampers or chassis position.
Agreed, only cut from the side fender a little. But it is from the air pushing the body down. Bending the plastic body posts slightly. I will do something to reinforce the body to stay consistent at speed
should i get an e revo 2.0 or a udr
I'd get a 6s typhon with a good 6s battery. Still come out cheaper than both of those options with better performance as well 😃
@@InnovationRC thanks for the advice
Hello brother, it would be very helpful for us Latinos who follow you if you activate the subtitles in Spanish that would help you also have more subscribers
Thank you for bringing it to my attention! I will get on that right now for you.
Edit* see if it works now
On PC, I think you can go to at the bottom of the video, on mobile find the 3 dots that will be settings:
settings> subtitles> auto translate> language of preference.
Only english comes out
PPS motor mount? Link??
Bob mahoney on Facebook or practicalprototypesolutions.com
Can I pls get a shout-out because I have subscribed and I liked