How To Front And Rear FJR1300 Brake Fluid Flush
ฝัง
- เผยแพร่เมื่อ 27 ธ.ค. 2015
- Flushing the FJR1300 brake system with new fluid is not hard but does take some time, especially if you have an ABS model. I show you the simple way of actuating the pump but alternatively you can access the battery area and jump the sky blue to black wires using the long diagnostic procedures (that varies per generation) you can google for. Bear in mind a normal flush will not 100% clear the system of old fluid, you do need to actuate the ABS pump once. The flush order is front left, front upper right - for the front circuit. Front lower right then rear, for the rear. Then hit the ABS on the rear and do the rear again.
Visit TwoWheelObsession.com for all the new content!
My Bike Reviews:
• 2014 Yamaha FJR 1300 E...
My How-To Videos:
• How To Detail A Motorc...
My Vlogs:
• The Start Of TwoWheelO...
Gear Overview Videos:
• Sena GP-10-A0202 Water...
All AIMExpo 2014 Coverage:
• 2014 AIMExpo Show Demo...
Leesburg Bikefest 2015 Videos:
• Complete Leesburg Bike...
Follow on Facebook: / twowheelo
Some music by ichillmusic.com
Join My FJR Enthusiasts group: / 793722307402142
AIMexpo 2015: • 2015 AIMexpo .
If you have a common question it is probably answered here: twowheelobsession.com/faq/ .
Police Motorcycle Competition:
• Full Video With Crashe... .
My editing/gaming build consists of:
• Playlist
My FZ09 / MT09 Mods:
Front Cowl: amzn.to/2jHBG5Q
Fog Light Kit: Yamaha Part BS2854A30000
Fog Light Bracket: Yamaha Part BS2854A50000
EBC HH Pads NEED 2 SETS: amzn.to/2soiCwe
Radiator Guard: amzn.to/2AnMz6P
LED Signals NEED 2 SETS: YME-W0789-00-00
LED Flasher Relay: tstindustries.com/TST-LED-Fla...
Gilles Tooling Brake Lever: amzn.to/2AnQaSl Yamaha Part 1RC-H39A0-V0-00
Gilles Tooling Clutch Lever: amzn.to/2BFqUp1 Yamaha Part 1RC-H39B0-V0-00
Rizoma Reverse Retro Mirror NEED 2: amzn.to/2gLbW7X Part BS070B
Rizoma Bar adapters NEED 2 Part LP300B
Rizoma Universal Bar Ends Pair: amzn.to/2kV9fp5 Part MA534B
Yoshimura R77 Full Exhaust WORKS Finish: amzn.to/2BC8yoJ
USB Port & Pigtail Kit: amzn.to/2zYGtL3
X-Grip: amzn.to/2ifSBwc
RAM Mount: amzn.to/2jHlFNs
Short RAM Arm: amzn.to/2BGcchl
Rubber Footpegs: amzn.to/2jI15fL
Yamaha Comfort Seat: amzn.to/2BE8TY6 Part BS2F47C0V000
Quickshifter Part BS2E81A0V000
Stoltecmoto.com Full Suspension & Brake Relocate Kit
Vcyclenut.com ECU Flash & Dyno Tune
Nelson-Rigg 2015 Magnetic Tank Bag: amzn.to/2AnFxPn
Nelson-Rigg Sport Tail Bag: amzn.to/2kha8rV
TWO recommended products: www.amazon.com/shop/twowheelo...
Visit TwoWheelObsession.com for all the new content!
My other channels:
CigarObsession: / cigarobsession
My Bike Reviews:
• 2014 Yamaha FJR 1300 E...
My How-To Videos:
• How To Detail A Motorc...
My Vlogs:
• The Start Of TwoWheelO...
Gear Overview Videos:
• Sena GP-10-A0202 Water...
Follow on Facebook: / twowheelo
Some music by ichillmusic.com
Join My FJR Enthusiasts group: / 793722307402142
If you have a common question it is probably answered here: twowheelobsession.com/faq/
My editing/gaming build consists of:
• Playlist Some background music by www.ichillmusic.com #motorcycle #motorcycles #howto #motovlog #review
As an Amazon Associate I earn from qualifying purchases. - บันเทิง
Normally, I love your tutorials - they are very thorough and informative, however, this tutorial falls short. What I was anticipating was a start to finish detailed video showing the actual bleeding process (front and rear), the recommended brake fluid type, the sequence, and other tips. I would recommend you remake this tutorial if you still own your FJR1300.
First -- thank you for all the very helpful videos. Really appreciate all the information and help.
Would it be possible to add a video that shows the actual drawing out and filling of the brake fluid (and clutch fluid), please? It would be nice to see how to use the vacuum tool to suck out the clutch brake fluid and at the same time fill the reservoir with fluid as you are drawing it out from the bottom, and show what it looks like when the old fluid is all drawn out and the new/clean fluid starts coming out.
motorcyclist magazine shows this procedure, just search for them on youtube
I didn't catch it in the video if it was mentioned, but the front bottom bleeder (the linked piston on the front caliper) is fed by the fluid reservoir for the rear brake, so be sure to watch the fluid level in that reservoir, not the one on the handlebar, when bleeding that one front piston.
Well all your videos helped me "give in" and traded my Kawasaki C14 for a 2015 FJR just this past Saturday and & love my new bike. Thx again for all your informative videos and if I have a technical question on my new bike I will drop you a line, ride safe & stay safe.
Thank you for taking the time to make these great videos! They’re super-helpful and very much appreciated.
Nice, detailed video. Enjoyable to watch!
Brian, thanks for the video, was able to all my fluids on my motorcyle in a few hours. Keep the videos coming.
Cool!
Thanks for the tips. This really helped me with my FJR.
.
.
.
Thanks
And the ability to observe the bike's engineering when any fjr panel is removed, camera movement is limited and lighting is ok is a bonus.
.
.
.
Thanks. Just performed the brake/clutch service as per this vid. 👍👍
Can you tell me if you have to activate the abs pump prior to doing the fluid flush on the front right caliper lower nipple (back) or do you do this prior to going a ride.
After returning from activating the abs pump is it just the back brake caliper that needs bleeding?
Hey man. It seems I'm not understanding fully....do you bleed all 4 brakes initially....the actuate the ABS via the stopping method and then bleed the rear two brakes (the one nipple on the front and obviously the back)? Also, the rest of your videos are extremely thorough and show every little detail, however on this one you do not show the actual process of bleeding and refilling the reservoir (which would help me out tremendously as I am a total newbie). Just a thought, but thanks for all your help so far as I'm a new FJR owner and subscriber
Good question I asked the same, I think to be certain I would repeat the entire process once you have test ridden it and actuated the abs, it’s only going to be a little extra dot 4 fluid
Nice video. Do you know how much fluid to buy before starting? It is not listed in the manual. DOT4
Great vid cheers
Managed to get the tool for my FZ1 not sure if it's the same part. It's an interesting test the bike does :) but you're right it's essentially a jumping few pins.
+Bikers Quest Different part and it's just 2 pins.
So once you have done rear brake flush, and actuated the abs, do you need to reflush rear brake system again, or just front nipple or back?
Hi mate, i've been enjoying the videos for a while now, so thanks for them! I was just wondering if there's anything I should be looking out for, other than the usual stuff, when buying used? I'm looking at a 2004 with 68K but with a FSH, looks very clean from the pics... I'm in the UK... Thanks :)
+Tris Desnos Nothing unusual, same as any other bike. Just make sure all recalls have been done if it's older.
+cigarobsession cheers mate
Thanks Bryan . save me having to take it all the way to a Yamaha dealer
Great video. What is the linked braking like in real world use, Is it worth the extra complication in your opinion?
+poldsmobile Phil Harrison Oh absolutely, makes braking silky smooth and you don't need to get the balance perfect each time with the controls.
How much fluid do you need to purchase to do the whole system?
I have an 09 FJR with no clutch, I have to pump the rear brake peddal or it just will not work, but if I use the front hand brake, both front and back engage just fine, any ideas as to what causes that ? or what my problem is ?
+ROB NAVAEI do a complete scheduled service including full fluid flush and seal change.
You need to explain why the brakes still work while it is on the stand but the abs pump needs to cycle to bleed the fluid out of the pump. Does the fluid by pass the abs pump under 6mph or does it still go through the pump like ever other abs pump braking system. Or is this whole hooking wires together a crock of .... so the dealer can get payed.
+Bill Hart I don’t know what the threshold is but yes there is a bypass
How much fluid do you need for full cluch & brake fluid change? Thanks!
1 large bottle is more than enough.
1 large bottle... meaning 1 liter or 1/2 liter?
@@GeorgeMaxxim My Gen 2 took a 12 oz (350 ml) bottle plus I little from a second bottle to flush the brakes and clutch.
So, you are saying that just flushing twice doesn't get the fluid in this ABS reservoir? That would mean the fluid sits there isolated until such time as you activate the ABS? It wouldn't be doing all that much harm to leave it then, would it?
Yes it does do harm. The ABS system is prone to rust and failure with old fluid trapped in it for long periods of time. You must actuate it to get out the old fluid.
In your other video you implied you have to lock up both front and back because there are two separate reservoirs. Is this correct?
Correct. Or use a tool/jumper like in my later vid to manually actuate the system, if available for your particular model.
What's the mpg on your FJR1300?
39. My last one got 41 before the days of ethanol.
+TwoWheelObsession Alright, online on fuelly.com it says average mpg about 45MPG. I have a Ninja 300 and I can only manage to get about 45MPG. Do you have any tips? I should be getting about 55MPG or higher. My bike has 11,000 used tires are balding and I am a new rider with 1,000 miles under my belt.
Thanks
+counkev MPG greatly depends on where you ride and how you ride it. I ride it WOT a lot. Sure if I ride like a granny I can get way more. Who cares about MPG anyway? It is what it is.
Similar procedure for a 2013?
+MrHeepspo same
Do all 07's have abs?
yes
Did I miss something? You never show how to actually flush the resevoirs, how to use the vacuum pump, how to refill / bleed.
4:54 That's what she said.