YAMAHA FJR1300 REAR BRAKE FLUID CHANGE ! Is THIS how YOUR dealer SHOULD do IT..!
ฝัง
- เผยแพร่เมื่อ 4 ก.ย. 2024
- This is how to do your own brakefluid change on the REAR BRAKE of your Yamaha FJR1300. Its easy as you can see in my video, and you save a lot of money too..!
Here you can find my Yamaha FJR1300 playlist:
• Yamaha FJR1300 2007
Motorcycle Maintenance For Beginners - AND What You Need To Know
With this DO IT YOURSELF video you can save a lot of money.
So be sure to watch this WHOLE video, so you don't mis important information.
Don't forget to SUBSCRIBE, LIKE and SHARE this video with your all your friends on FaceBook and WhatsApp.
If you want to support my channel, so I can make more of these maintenance video's for you,
please push the --- ♥️ THANKS -- button below. Any amound is more then welcome.
Have a look at my 'The Old Mechanic FAN WEAR' store:
my-store-cb705...
#theoldmechanic #motorcyclemaintenance #yamahafjr1300
Good job ....but I think the rule of thumb is "always bleed from the farthest bleed valve" which means for bleeding rear brake, since the reservoir is close to the rear tire, then you do the front bleed valve first. I am talking about the bleed valve on the front which works in tandem with rear break. (aka combined, or sinced). I am not talking about front brake. (too many rear and front ... might confused folks).
I just bought a pack of those trim removal tools after your other vid. Makes removing those quick fasteners a lot easier than a screwdriver.
I enjoy watching someone that not only knows what they are doing but will take the time to explain why you should and why you should not, thank you .
Sir,
After Delboy's Garage taught me to push the brake fluid from caliper , I no longer go back to the first method (feeding the fluid from the top). Pushing the new fluid from the caliper to the spare tank takes much less time.
You need a 60 ml generic syringe (with a wide nose), connect the tube to it, open the SCREW BLEEDER, and push brake fluid from the caliper upwards. Sometimes very little air penetrates through the threads of the SCREW BLEEDER, and then the air bubbles are removed in the traditional process that you demonstrate (a few clicks and the air is out). To avoid this, you can screw the SCREW BLEEDER with Teflon tape.
Another easy and simple operation that helps to drain air bubbles: With the help of a strap, leave the brake lever pressed for several hours with light pressure (not to press hard),
But surely you already know that.
perfect videos u make ..i learn from u.give more fjr1300 videos about light's adjust front ..back...battery change...feuses ..and more..i am knew owner. thnx
I'm from Poland but I like to listen the way you are pronouncing words. 😊
Hiw tô bleed the ABS??
Thank you for sharing your knowledge.
Your welcome 😉
thank you
And the ABS sistem? How can purge?
Hello Old Mechanic hope your well. I see that some antilock break systems require the software to complete the job. So not all bikes do? Also thanks for the tip on the front caliper on bleeding for the rear.
Randy
Common problem on the FJR1300..that rear brake lever pivot getting dry and lots of road grime in the pivot.
Right 😉👍🏻👊🏻
I love this guy's videos but I am a little bit confused. Is it not necessary to Bleed the air from the brake lines?
I have a 2014 Yamaha FJR 1300A (Red) and usually let the dealer do that procedure.
Is it enough 2,5 dcl for change both sistem, front and rear.? I buy 250 mll of brake fluid..
Unfortunately you never got rid of the old fluid in the ABS Pump. Watch the videos below. This should better your exercises.
I how your next job was you suspension knuckle 😳
In English just pronounce it 'dia-fram'. 😘👍
guindo youssouf. tegunisene motards fjr YAMAHA ala douanes escorte motards