Hey Chris some really good info there and I like the way you explain what you are doing and why you do it at each step along the way it makes it a lot easier to follow👌 That budget gun does an amazing job at laying the base and the clear as the finish is really nice, seeing as you are not in a booth your jobs always seem to come out very clean👏👏👍John UK
Great teaching video. I owned an aircraft paint shop and would have to teach the guys the right way to prep and paint before they attacked a major job. I wish I had this video then. One little trick on the proper fluid volume. Turn off the air and then note the fluid stream…make it just less than a full stream. This also tells you about your reducer amount on a high solids paint.
Great video. Question for you How do you remove or lower the amount or remove the cloud that is in the air when spraying the clear coat. I'm in a garage not a booth
Great video! Can you tell about the light you attached to the gun? Does it help to get even coats when you spray? I usually get decent results when my lighting is good but that's not always the case. I have never tried to attach a light to the spray gun...
I like it, mostly fore basecoat or if I'm clearing something low where I don't have enough light . It's only 60 bucks and comes in handy. Here's the link amzn.to/3KI9GNK
I use Sata-95 for base and a Iwata for clear. I don't use the light on the spray gun. I like to do collision work, body work, primer, prep work, buffing black paints.
It depends, I use the spot panel upol for most jobs because it dries a bit quicker. If your doing a full paint use the overall upol clearcoat it stays wet longer .
Hi chris I used this primer and I let it dry over a week cause the wheather didnt permit when ivwas sanding it it was a nightmare it didnt dry i spent hours sanding it was clogging all my sand paper what else you used beside reducer to make it dry faster do u have any dryin issues or clogging the paper ? Whats a better primer option that will sand smooth easily ? Thanks again
Chris is it possible to spray upol 2253 as a high build primer with the R500 or is that asking too much from the 1.7 tip? If so any settings would be appreciated.
1.7 would spray upol high build no problem. If you get alot of texture or orange peel it might be a little big so switch to the 1.5 if you have it. If you don't it's not a big deal the 1.7 will work. As far as the settings I would adjust you fan the width you like it and start with the fluid at 3 turns out from closed. The air pressure at about 15 to 18 psi. Appreciate the comment and support!
Just did clear on the hood and it came out perfect a little dirt cuz I'm in the garage. Doing a g20 van . last thing to paint is that big panel on the drivers side. No windows . i be a little scared. Ill let u know.
Getting ready to do sealer and the biggest panel how long can I let that sealer go before I put the base on I got some other things I got to do can I go 36 hours? I turn down the heat in the garage a few hours after spraying.
@@davidgentz1731 check your TDS (technical data sheet) for the product your using. 36hrs may be to long to wait. Typically tje longest you should wait is 24 hrs. After that you need to scuff it up again before basecoat. I like to stay within a 4 hour window.
![[LIVE] : ONE ลุมพินี 83 วันนี้!! คู่เอก "พันฤทธิ์ vs ซุปเปอร์บอล วันของโอม MBK"](http://i.ytimg.com/vi/1b4pkKHa_Fk/mqdefault.jpg)
Since I have not sprayed a clear coat as of yet your info is great. Very much appreciated. You are a good teacher.
I appreciate that!
Hey Chris some really good info there and I like the way you explain what you are doing and why you do it at each step along the way it makes it a lot easier to follow👌
That budget gun does an amazing job at laying the base and the clear as the finish is really nice, seeing as you are not in a booth your jobs always seem to come out very clean👏👏👍John UK
Happy it was helpful brother! Appreciate the support!
Awesome I'm in the learning process thanks to your videos
Appreciate the comment and support! Your welcome!
I watch your videos all the time good job excellent information 👍
I appreciate that! Thanks for the support!
thank you for your tips and experience
My pleasure!
Great job.....and explanation !! Love this channel !!
Thank's David, appreciate the comment and support!
Looks beautiful great job thank you 👍
Thank's Joan appreciate the comment and support!
A headlamp on the gun cup, Bloody Genius!!!
Good video. Thanks for all the great tips.
Thank's Bud!
Yeah I'm going to try your way hope it works for me I got some runs today I got to fix it I'm so mad now
So many good tips in this video. Thankyou.
You're so welcome! Appreciate the comment and support!
Looks good. Two coats of base and a drop coat. Metallic paints I use the cross spray technique.
Right on! Appreciate the comment and support!
Great video learn a lot
Thank you very much for a detailed instructions! Great video. Do we need to address a dry edge created by the sealer? Thanks.
I don't really have a problem with the edge of sealer but I did use upol #9 blender on the edge. I didn't show it in this video.
@@GarageNoise 👍👍👍
Nice looking good 👍
Thanks 👍
Great teaching video. I owned an aircraft paint shop and would have to teach the guys the right way to prep and paint before they attacked a major job. I wish I had this video then. One little trick on the proper fluid volume. Turn off the air and then note the fluid stream…make it just less than a full stream. This also tells you about your reducer amount on a high solids paint.
Right on! Appreciate the comment and support!
Awesome work! Thank you for the tips 👍! I heard Devilbiss FLG-5 is a good spray gun! That you want give it a try!
Thank's brother! I heard the same thing about the flg5. Appreciate the comment and support!
Another great tutorial!
Thank's brother!
Top job, Mate.
👍
Great video. Question for you How do you remove or lower the amount or remove the cloud that is in the air when spraying the clear coat. I'm in a garage not a booth
I have the perfect video on that topic! th-cam.com/video/At_WlTqXkt4/w-d-xo.html
Can you do a video showing gun prep/cleaning when switching from primer to sealer to base to clear etc..
Sure, will do!
Great video.
👍thank's Dan!
Awesome job!
Thanks! Appreciate the support!
Great video! Can you tell about the light you attached to the gun? Does it help to get even coats when you spray? I usually get decent results when my lighting is good but that's not always the case. I have never tried to attach a light to the spray gun...
I like it, mostly fore basecoat or if I'm clearing something low where I don't have enough light . It's only 60 bucks and comes in handy. Here's the link
amzn.to/3KI9GNK
Awesome 👍
Thank's Dave! Appreciate the support!
Perfect
👍
I use Sata-95 for base and a Iwata for clear. I don't use the light on the spray gun. I like to do collision work, body work, primer, prep work, buffing black paints.
👍
How that clear coat is different from the standard Upol you normally use? How big of a job would be to decide which one?
It depends, I use the spot panel upol for most jobs because it dries a bit quicker. If your doing a full paint use the overall upol clearcoat it stays wet longer .
Hi chris I used this primer and I let it dry over a week cause the wheather didnt permit when ivwas sanding it it was a nightmare it didnt dry i spent hours sanding it was clogging all my sand paper what else you used beside reducer to make it dry faster do u have any dryin issues or clogging the paper ? Whats a better primer option that will sand smooth easily ? Thanks again
What primer were you using?
You probably were using a 1k primer. If so get rid of it and use a 2k which is catalyzed so you won't have that issue.
Can you show the name and brand of reducer you are using?
I use usc slow in this heat
amzn.to/3Au3s0Q
would this video be applicable to a gun like the new version r500 ? that's what i have .
No, but I have plenty of video's sharing gun setting with the new R500
Hi when l paint my car white colour the colour it's change to cremi (yellow) what's problem
Not sure, the whole car or is it just a spot
Chris is it possible to spray upol 2253 as a high build primer with the R500 or is that asking too much from the 1.7 tip? If so any settings would be appreciated.
1.7 would spray upol high build no problem. If you get alot of texture or orange peel it might be a little big so switch to the 1.5 if you have it. If you don't it's not a big deal the 1.7 will work. As far as the settings I would adjust you fan the width you like it and start with the fluid at 3 turns out from closed. The air pressure at about 15 to 18 psi. Appreciate the comment and support!
@@GarageNoise you are awesome. Youre videos have given me great start on how to use the R500 to its max potential.
👍
My base started to spider web. Does anyone why?
Sounds like a chemical reaction. Shoot a photo to my email I'll try to help ya out.
garagenoise247@gmail.com
6:25
The missing link was the fluid volume from close, i base coated today. Came out beautiful. Thanks
Ok, good to know . Happy it worked out.
Just did clear on the hood and it came out perfect a little dirt cuz I'm in the garage. Doing a g20 van . last thing to paint is that big panel on the drivers side. No windows . i be a little scared. Ill let u know.
@@davidgentz1731 awesome! Happy to hear it. Keep you spraying speed at a good pace and don't spray scared and you should have no problem on the g20.
Getting ready to do sealer and the biggest panel how long can I let that sealer go before I put the base on I got some other things I got to do can I go 36 hours? I turn down the heat in the garage a few hours after spraying.
@@davidgentz1731 check your TDS (technical data sheet) for the product your using. 36hrs may be to long to wait. Typically tje longest you should wait is 24 hrs. After that you need to scuff it up again before basecoat. I like to stay within a 4 hour window.