Thanks for another great video guys! I'm going to need to replace both heater cores on my 2011 cascadia. I was told that they are both the same is that true? Thanks again
You can do that to but I am not sure that will work because they are supply for the front and for the rear. Depends on the setup and I don’t remember off the top of my head.
Broo una pregunta mi cascadia 2015 el ac funciona bien cuando esta parado . Pero el manejar sale como a 70 grados.pero al parat de nuevo baja la temperatura. Que podrá ser ?
Spn 521485 fmi2 I can’t see N D or R it just says gear pos.sensor detected shifts inhibited. Any idea what it could be? It will not go in any gear but Engine stars every thing is normal . Dd 15 dt12 trans auto 2015 thanks
From what I have read, it could be a programming issue. But I don’t have enough experience with DT12 transmissions. I would recommend to have someone plug in with the DDDL software and see if there is a way to possibly recalibrate or maybe reset the transmission using the software. Wish I could help you out more.
I usually drain at the radiator or depending on the job I drain at the block and the radiator. When I refill, I add at the surge tank, start the truck without the cap and allow it to run. Air will work its way out, then I add accordingly. Also, turn on the heater for the cab and sleeper while the truck is running. This will allow the coolant to run through the system, let the truck get to operating temperature and you should be fine.
hola amigo pedro una pregunta tengo un cascadia 2014 una manguera que biene del heater core anda volando quiero saber si es normal a va conectada sa algun lugar
I can smell antifreeze in the cab but no visible leaking in the cab. Had the radiator replaced for a leaking issues. Can you give a suggestion of what to do to get rid of the smell?
Depends on how bad the heater core is. But is can be a small leak or large. But if you have a leak on that side it most likely is the heater core and needs to be looked at or replaced.
One gallon a day is a lot. The heater core takes about 2-4 hours total. Between getting the part, removing the coolant and then start and finish. Which air tube are you referring to?
Señor buenas tardes, el aire dejó de soplar por las ventilas de la cara, en la posición de la cara sopla hacia el vidrio, alguna idea para resolver ese problemita, de antemano muchas gracias.
The coolant leak would affect heating, your AC condenser or evaporator would affect cooling. Have some check your system, could be the AC compressor, could be low on Freon?
Wey que será que cuando estoy andando se abre la entrada del aire de afuera y comienza hacer un ruido de viento, me toca volver a tocar el botón de recirculate para q deje de sonar apenas compre mi cascadia tiene 400.000 millas y no se q es, gracias amigo!
Hey buddy, can u let me know with the video that where is the heater core shuttoff valva located in freightliner cascadia? Actually we installed the heater core but a mechanic he shutoff the valve because coolant was leaking inside so now i don't know where is that valve located so i can turn it on and my heater work Thanks
Does anyone know the tube fitting sizes? I want to make a bypass. I just changed the thing a few months ago & its leaking again! I'm gonna submerge the thing, fill it with air & jb weld the leak with fiberglass.
@@dd15trucker22 I recommend to replace the fan blower, there is an updated harness that you will need to purchase. Sounds like the fan blower needs to be replaced.
So on that plastic intake with the screw you said you’re going to get a tool & the manufacture put it in a difficult spot why didn’t we get too see how you took that off ??? Void’s the whole video please lmk how to get that last screw off without cutting off the bracket
The part runs about $120 plus tax Then labor is about 2-3 hours, so depending on the labor rate. So let’s say about $250-$300 for labor. 120 part plus sales tax 250-300 labor $400 for parts and labor (estimate)
@@benjaminnorberg2265 nothing special just alot of maintenance. I change my oil at 20k. I change all oil and diesel filters with every oil change. I change my engine air filter every 100k miles. transmission and axle wise I change those oils every 100k i also change the power steering pump oil and filter every 100k. idk if your truck has a coolant filter but I change that every oil change too.
I just removed the air filter housing in order to give me more room to work and because coolant lines will need to be removed and the housing gets in the way. But I’m sure you can do the work without removing I just think it would be a little easier without it in the way.
es lo que le pasa a mi camion, no encontraba de donde venia ese olor, ahora manos a la obra, muy buena explicacion y muy buen video
Que Padrisimo hermano en Español!!
Un millon de gracias por el video, me sirvio mucho tu enseñanza.
Came over here because longhaul larry gave you a shout out on your fuel priming tank thought I would check you out
Thanks for stopping by, hope you like the videos.
Saludos des de n.hollywood ca
Mr.pedro muy bueno ese y todos los videos ,gracias asi son buenos para todos los operadodores podemos aserlo
Muy claro su video lo felicito gracias por compartir su conocimiento definitivamente ya me suscribi a su canal muy bien explicado saludos
Exelente video y aun mejor la explicacion del trabajo conbinado con la instruccion paso por paso en ambos idiomas saludos desde. Calexico calif.
Gracias mañana me Toca Hacer lo que nos explicas en Este video.
You guys are some beautiful people!!! Thank you very much for this video!!!
Thank you
For that 3rd screw, just drill a big enough hole in the beige plastic for the screw head to fit thru. Boom, screw access hole.
Thanks I just commented on that
Gracias m3 ayudo mucho tu video u are the best bro thanks
Good video Carlos. Keep'm coming!
Thanks good for a your video 1 million likes for you
You are the best, very good video. 👍
Thank you.
Gracias x tu ayuda me ahorraste $500 dllrs 👍🏻👏🏻👏🏻👏🏻👏🏻🤛
Me da gusto 👍🏼
Gracias por poner el video de mucha enseñanza.
you should do a video of how to replace the AC evaporator
Great idea, thanks. I am trying to change it up to more DIY videos.
Saludos maestro Pedro muy buen vídeo
Gracias
Muchas gracias bro! 👍🏽
good video bro, keep it going 💯👍
Very helpful video 👍 thank you
1 million likes for uThanks good your a video
Great explanation!
Great video,from a great person!!!
I love you can explain it both ways. Just subd
Gracias muchas gracias. God bless you always
Very helpful video .
Thanks for another great video guys! I'm going to need to replace both heater cores on my 2011 cascadia. I was told that they are both the same is that true? Thanks again
Yes they are the same.
yes, my 2015 has the same size
YOU'RE THE BEST ... THANK YOU SO MUCH
You are welcome.
Shut off valve's are on the left rear side of the EGR cooler above the turbo.
You can do that to but I am not sure that will work because they are supply for the front and for the rear. Depends on the setup and I don’t remember off the top of my head.
Just changed mine. Just seems like the heater core has some play where it can move around in the box. Is that your experience
Awesome 😎 thank you 🙏
Ese problema tengo en este momento y quiero hacerlo yo. Una pregunta maestro habrá algún material q se pueda usar para tapar esa pequeña fuga?
Normalmente se tiene que cambiar las partes para sellar. Las ligas o seals se pone duro como plástico.
Pero diga cual mangers en cual salida o Entrada.. Lo digo para Los ke por primera ves somos dueños de una cascadia
Buen día,,, disculpe la molestia quiero saber por dónde drena el condesandor de aire acondicionado ya que el que traigo yo tira el agua por dentro
Debe de tener un canal de drenaje. Puede ser que está tapado. En frente por lado del pasajero revisa la manguera.
Broo una pregunta mi cascadia 2015 el ac funciona bien cuando esta parado . Pero el manejar sale como a 70 grados.pero al parat de nuevo baja la temperatura. Que podrá ser ?
If the truck is leaking coolant inside the truck turn the shut off valves to the off position until you get the problem fixed.
How can you do that sir. Where can i find the valves?.I’m trying to do that until i get to a safer place.
The valves are located on the passenger side. Just above turbo to the left. There should be two valves near the number 5 cylinder.
Spn 521485 fmi2 I can’t see N D or R it just says gear pos.sensor detected shifts inhibited. Any idea what it could be? It will not go in any gear but Engine stars every thing is normal . Dd 15 dt12 trans auto 2015 thanks
From what I have read, it could be a programming issue. But I don’t have enough experience with DT12 transmissions.
I would recommend to have someone plug in with the DDDL software and see if there is a way to possibly recalibrate or maybe reset the transmission using the software.
Wish I could help you out more.
when you drain and refill coolant, do you drain from radiator, and then refill at surge tank? how do you prevent air pockets from damaging components?
I usually drain at the radiator or depending on the job I drain at the block and the radiator. When I refill, I add at the surge tank, start the truck without the cap and allow it to run. Air will work its way out, then I add accordingly. Also, turn on the heater for the cab and sleeper while the truck is running. This will allow the coolant to run through the system, let the truck get to operating temperature and you should be fine.
hola amigo pedro una pregunta tengo un cascadia 2014 una manguera que biene del heater core anda volando quiero saber si es normal a va conectada sa algun lugar
El core tiene dos mangueras y el sleeper tiene dos mangueras. Cual manguera hablas?
I can smell antifreeze in the cab but no visible leaking in the cab. Had the radiator replaced for a leaking issues. Can you give a suggestion of what to do to get rid of the smell?
It maybe linking from the block
Hi pal got a similar issue, just wanted to know if it pours a lot,coz mine leaks so much
Depends on how bad the heater core is. But is can be a small leak or large. But if you have a leak on that side it most likely is the heater core and needs to be looked at or replaced.
How long did it take to remove the air tube?would this explain a gallon a day loss
One gallon a day is a lot. The heater core takes about 2-4 hours total. Between getting the part, removing the coolant and then start and finish.
Which air tube are you referring to?
Señor buenas tardes, el aire dejó de soplar por las ventilas de la cara, en la posición de la cara sopla hacia el vidrio, alguna idea para resolver ese problemita, de antemano muchas gracias.
Puede ser el control o puede ser atrás del tablero. Las puertas. Empieza con el control total prueba con otro primero
Saludo hermano quiero saber donde va la manguera del agua y cual sería la otra manguera que lleva espero su respuesta
Son cuatro mangueras, una es supply y return y las otras dos son para la cabina para el calentón del sleeper.
Can the coolant go up and over into the A/C area
@@daveh2068 if coolant leaks it can go down and around the floor. What is happening with your truck? Give me more details and I can try to help.
Sir my truck ac not working coolant little bit leak bottom on the ac filter
Dd15 Cascadia
The coolant leak would affect heating, your AC condenser or evaporator would affect cooling. Have some check your system, could be the AC compressor, could be low on Freon?
Wey que será que cuando estoy andando se abre la entrada del aire de afuera y comienza hacer un ruido de viento, me toca volver a tocar el botón de recirculate para q deje de sonar apenas compre mi cascadia tiene 400.000 millas y no se q es, gracias amigo!
Hey buddy, can u let me know with the video that where is the heater core shuttoff valva located in freightliner cascadia? Actually we installed the heater core but a mechanic he shutoff the valve because coolant was leaking inside so now i don't know where is that valve located so i can turn it on and my heater work
Thanks
There are two valves on the passenger side of the block that supply the cab. Start there, most people shut them off
Does anyone know the tube fitting sizes? I want to make a bypass. I just changed the thing a few months ago & its leaking again! I'm gonna submerge the thing, fill it with air & jb weld the leak with fiberglass.
I believe 5/8 and 1/2 is the OD of the hoses. Call your local Freightliner. They might be able to provide you the size of each.
when I turn on the heater I get a headache, I don't see a leak but the headache starts when the heater is turned on. Any suggestions?
Is the vent open? Is it air from the outside? What happens when you close the circulation?
Where are you based out. Just in case I wanna use your services? Thanks for the upload brother
I am in Southern California. Montebello, Ca 90640
@@CarlosDieselElectric thanks budd. Appreciate all the great info you share with us.
Yo lo cambié amigo pero sigue saliendo aire caliente por las ventilas dime que puedo haver
How do you get rid of the nasty coolant smell coming out of the vents once the core heater is installed?
Apparently the Loves mechanic that installed mine didn’t drain the coolant out before installing.
Sometimes the smell is in the carpet or insulation. Only time will allow the smell to go away.
@@CarlosDieselElectric thanks for the valuable information
Try to rinse and dry everything that got wet then put dryer sheets under the carpet. Coffee grounds help too.
I have a quick question. I am trying to replace a AC Blower Resistor, but I can’t find where it located at. Can you show where it is?
What is it that is happening?
@@CarlosDieselElectric stuck at one speed
@@dd15trucker22 that might be the blower itself. Have you tried with another fan blower?
@@CarlosDieselElectric I have not
@@dd15trucker22 I recommend to replace the fan blower, there is an updated harness that you will need to purchase.
Sounds like the fan blower needs to be replaced.
do you need too drain all the antifreez from the system?
I would drain about 5-10 gallons of antifreeze. Since the heater sits up high, the amount of coolant isn’t too much.
Pinch off the hose's you don't need to drain coolant you will only lose what is in the heater core.
clip này hay lắm ạ
❤❤❤❤❤❤❤
So on that plastic intake with the screw you said you’re going to get a tool & the manufacture put it in a difficult spot why didn’t we get too see how you took that off ??? Void’s the whole video please lmk how to get that last screw off without cutting off the bracket
Again you said the antifreeze tubing you didn’t show it @ the end of video 🤦🏻♂️ bruh 😂😂
How much coolant do you have to drain?
You will still have coolant present, but I remove about 5 gallons or so from the system.
Que Sera la Contreras esta bien tyenenbion y no enbria aber sime pueden ayudar
Hey buddy! How much was it for this repair?
The part runs about $120 plus tax
Then labor is about 2-3 hours, so depending on the labor rate. So let’s say about $250-$300 for labor.
120 part plus sales tax
250-300 labor
$400 for parts and labor (estimate)
@@CarlosDieselElectric thank you for replying and helping us out with valuable information!
What is the hose sizes? Inside diameter
Maybe 1/2 or so. They are usually a dealer only item due to the prefabricated bending.
Teléfono por favor gracias
That guy need a rebuild yesterday
I agree, hopefully he can get some more miles out of it.
I'm at 1418748 all original miles
That is impressive, I have not come across a DD15 with that many, just one with 1,249,000 miles.
@@CarlosDieselElectric I just recently replaced the rod bearings and main rod bearings and the oil pump. besides that everything else is original
@@jorgefacio690 Any tricks you do to get that many miles on your truck?
@@benjaminnorberg2265 nothing special just alot of maintenance. I change my oil at 20k. I change all oil and diesel filters with every oil change. I change my engine air filter every 100k miles. transmission and axle wise I change those oils every 100k i also change the power steering pump oil and filter every 100k. idk if your truck has a coolant filter but I change that every oil change too.
Hi
Damn i think i have this problem coolant under floor mat
Remove the panel and take a look. Takes a few minutes
I dont see how air filters in the way unless youre 400 lbs
I just removed the air filter housing in order to give me more room to work and because coolant lines will need to be removed and the housing gets in the way. But I’m sure you can do the work without removing I just think it would be a little easier without it in the way.
@@CarlosDieselElectric thank you sir. Its a great video. Ive just subscribed. I really appreciate you.
Mine leaked at 830000
you should do a video of how to replace the AC evaporator