Build 5-inch freestyle fpv drone | SpeedyBee Master 5 HD frame
ฝัง
- เผยแพร่เมื่อ 30 มิ.ย. 2024
- This step-by-step guide to building a 5-inch freestyle drone, that is based on the SpeedyBee Master 5 HD frame and SpeedBee F7 Flight controller and ESC.
DJI O3 system is installed on this drone and I used the Xing2 2207 1750 motors.
SpeedyBee Master 5 HD Frame is designed with a wider X frame with a low center of gravity.
The original DJI O3 coaxial cable was replaced with a longer one.
Products used in this build:
SpeedyBee V3 F7 Flight Controller Stack:
www.speedybee.com/speedybee-f...
Amazon: amzn.to/3qPsItv
AliExpress: s.click.aliexpress.com/e/_DdF...
SpeedyBee Master 5 HD FPV Drone Frame:
www.speedybee.com/speedybee-m...
Amazon: amzn.to/42V8rA2
AliExpress: s.click.aliexpress.com/e/_Dms...
Xing2 motors:
Amazon: amzn.to/3PoC35R
Banggood: www.banggood.com/custlink/DDv...
AliExpress: s.click.aliexpress.com/e/_Dm2...
DJI O3 :
Amazon: amzn.to/43OjP28
AliExpress: s.click.aliexpress.com/e/_DcJ...
RadioMaster RP1:
Amazon: amzn.to/3XjHVix
AliExpress: s.click.aliexpress.com/e/_Ddl...
MATEK BEC: amzn.to/3pcA4qw
VIFLY Finder V2:
Amazon: amzn.to/3Ngy3BD
AliExpress: s.click.aliexpress.com/e/_DkU...
Tattu R-Line Version 3.0 1400mAh:
Amazon: amzn.to/3JpNTsv
AliExpress: s.click.aliexpress.com/e/_Dmg...
CNHL 1500:
Banggood: www.banggood.com/custlink/KDG...
AliExpress: s.click.aliexpress.com/e/_DFa...
Wiring Harness Tape:
Amazon: amzn.to/3NEuiqZ
AliExpress: s.click.aliexpress.com/e/_DmS...
HQProp Ethix P3.5:
Amazon: amzn.to/3NlCPxW
AliExpress: s.click.aliexpress.com/e/_Dk3...
Gemfan 51466 V2 5inch 3 Blade/tri-blade:
Amazon: amzn.to/4868Jrz
AliExpress: s.click.aliexpress.com/e/_DDT...
Chapters:
00:00 Intro Bilu MEDIA
00:25 SpeedyBee Master 5 HD FPV Drone
01:47 Components and Tools
06:58 The Build
28:42 Testing the drone
32:40 How much does it weight?
33:11Configuration and Setup
42:08 Final Thoughts and Flight Test
Support my work here: much appreciated 😊
www.buymeacoffee.com/bilumedi...
Drones:
DJI Avata: amzn.to/3zbCg3w
DJI Goggles INTEGRA :
AMAZON: amzn.to/3sF8OCq
Banggood: www.banggood.com/custlink/v3G...
DJI FPV: amzn.to/3DqBfXL
FlyWoo Nano Baby 2.0:
AMAZON: shln.top/MmiPKfdL
Banggood: www.banggood.com/custlink/DDD...
FOXEER FOXWHOOP:
AMAZON: amzn.to/3MQMb5I
Banggood: s.click.aliexpress.com/e/_Dcg...
BEST FPV TOOLS:
MINIWARE TS101 :
AMAZON: amzn.to/3WzJ19B
Banggood: s.click.aliexpress.com/e/_DBK...
Solder:
AMAZON: amzn.to/44BgT8E
Banggood: www.banggood.com/custlink/DDD...
AliExpress: s.click.aliexpress.com/e/_DDE...
Flux:
AMAZON: amzn.to/3sKFv1e
AliExpress: s.click.aliexpress.com/e/_DdQ...
MINIWARE ES15:
AMAZON: amzn.to/3qbCeqM
AliExpress: s.click.aliexpress.com/e/_Dkb...
Helping Hands:
AMAZON: amzn.to/3Mv8Umj
AliExpress: s.click.aliexpress.com/e/_Dei...
Weller Soldering mat : amzn.to/3MSciZT
HOTA D6 Pro Balance Charger : amzn.to/3qdXlZa
VIFLY Smoke Stopper: amzn.to/3BTjz5C
Precision Tweezers Set:amzn.to/3Nh9xQU
Wagner Heat Gun: amzn.to/449H86d
RADIOMASTER Tx16S II MAX :
AMAZON:amzn.to/3TwXErV
AliExpress: s.click.aliexpress.com/e/_DCU...
RADIOMASTER Pocket:
Banggood: www.banggood.com/custlink/vvv...
AliExpress: s.click.aliexpress.com/e/_Ddz...
RADIOMASTER Boxer:
Amazon: amzn.to/3qR7iwG
AliExpress: s.click.aliexpress.com/e/_DEc...
Banggood: www.banggood.com/custlink/GDm...
3D Printer:
amzn.to/3RXLVD0
Cameras:
Nikon D850 : amzn.to/3D3dLGQ
Nikon Z6 II : amzn.to/3N1B745
Nikon D810 : amzn.to/3TnFFUR
Nikon D750 : amzn.to/3DlcdZ1
Fujifilm XT4 : amzn.to/3VZj7LJ
Lenses:
Nikon Z 14-24 mm : amzn.to/3DqkYC3
Nikon F 24-70 mm : amzn.to/3z87LeM
Nikon F 70-200 mm: amzn.to/3sk3fGh
Nikon F 105 mm macro : amzn.to/3slKRwL
Nikon F 24 Tilt - Shift : amzn.to/3TQN6E0
Fujifilm 16-80 : amzn.to/3gCRx73
Action cameras:
Gopro Hero 11 black : amzn.to/3DpomwX
Gopro Hero 10 black : amzn.to/3TPIw8R
Runcam Thumb Pro : amzn.to/3Wt5ZPL
Bilu Media: Product Photography Studio and Retouching services based in Hamburg, Germany.
www.bilumedia.com
**Those links are affiliate links and I get a small kickback for them. Thank you for your support!
#fpv #drone #bestdrones #diydrone - ภาพยนตร์และแอนิเมชัน
You're missing about 500k subscribers for this type of content.
Thx
Hello my friend. What you mean exactly? Step by step and it will be, i love building drones and diy projects in general and eventually it will be reflected in the number of the subscribers if i keep doing it, and i will keep doing it because it is a passion first of all 😊
@@bilumedia I meant that this is tremendous work! Very nice!
@@dirtypeach thanks man, much appreciated, it is hard to gain subscribers, but with perseverance and passion it will happen eventually 😊
@@bilumedia You should add the "75 mm 6 pin ESC to FC" cable you used to the description.
@@dirtypeach i don’t understand what you are saying! You mean the longer one? I used the shorter one because i don’t like to see wires all over the place
You are so underrated. I can’t believe how good you explained everything really! Other videos cant compare with yours! Thank you for helping how to build my first drone❤
Thank you very much for your support and kind words. This kind of comments and appreciation keeps me doing this, because i see that i can help others and this motivates me a lot ☺️. Stay tuned, i have more more builds coming soon 💪
Thsi needs 100 times more views. Great video and editing!
Thanks for the kind words, I appreciate it very much 🤗 it will have much more views, steps by step 💪
I finally build my drone using this tutorial. Thanks a lot, @bilumedia!
My question, what can I build next, cause now I have tons of utilities :)
It is my pleasure, i am really happy that i could help you. What do you need? What kind of flight characteristics do you want? Exactly in this moment i am heading to the woods to film another build tutorial in the nature 😅. I am transforming actually my foxeer foxwhoop 25 drone intor an O3 drone, this was my first drone and i love it, of course it is easier to build a drone using a frame that is ready for the O3 as this one is not, but i love challenges and creativity and diy projects 😁! So tell me what you need and lets do it !
I am waiting for aos 7 ul frame that is stuck a little bit on the customs, but this is my next project, i have all the parts ready for it …
Lets connect in instagram, maybe you can film your drone and flying, i am curious how it turned out 💪
Congratulations on your first build 👏😊
if you read the specs there are built BEC 9 volt & 5 volt at F7 V3 Speedybee FC btw
Hello. I know! And normally you won’t have any problems at all, but my friend had a problem with the o3 turning into complete black, even if the bec was powerful enough, not with the this FC! I wanted to be extra sure, so i baby proofed this one 😅, but i am not doing it anymore unless it is absolutely mandatory, with some older units … but you are absolutely right, thanks for the valuable info 🤟
I like how you spoke about the tools. Not many, if any, that talk about the tools. I've been wondering which to get or what's needed. I like to make sure to have the right tools before starting projects. Especially like this. Also good to include that in the budget.
Hi my friend, i talk about them because you need them to do the job, now some of them are sponsored tools and are expensive, but if you do this a lot they worth the cost, if not then there are some cheaper alternatives 😊!
The best video of building drones I've ever seen!
Thank you very much, I am very happy that i helped in some way, if you need help just ask 😊
GREAT VIDEO MAN
Thanks man 😊
Excellent instruction! Thx for that!
You are very welcome 😊! Thanks for your kind words !
Amazing video! Million thanks made everything much clearer and now I can't wait to start building my own 😊
Thanks David for your support and kind words ! this is what keeps me doing these videos 😊. If you need help with your build please feel free to reach out to me on instagram : bilu.media! Good luck with your build :)
This video clearly explain the betaflight that i need to know for my first build. Thank you for sharing! God bless.
Thank you my friend for your kind words! If you need any help let me know 😉
Love your video man❤
Thank you my friend 😊
Wow nice video keep up the good job
Thanks man 🤗, much appreciated . I have 5 more builds coming this summer and some of them are custom made with designed 3d parts to fit my vision ☺️
Heat gun is overkill for heat shrink tubing...just use the shaft of your soldering iron if you dont feel comfortable using a lighter
maybe you are right, but I have it and this is why I am using it, if I am travelling I use a lighter and it works just fine, thanks for the tip 👍
Hi all!
All worked during testing. But stoped (see no reason why)
Might be somebody in south California can help me with my problem ?
Will be highly appreciated
Make a video on how to update fatshark doninator on macos pls 🙏
Hi, i would love to do that, but i dont have the fatshark system !
Hi, great video, I’m assembling the same drone and I also wanted to get my esc facing forward and my fc facing backwards for the O3 unit but the cable is too small, where did u get a longer cable?
Hi, thank you very much! yeah the original cable is too short for this frame, here is the cable that I used : bit.ly/3FG6jmy, the V2 frame I understood that is a little shorter and doens't need this cable, but I am not entirely sure!
Man are you using the goggles 2 ? did you figure out your osd?? I am struggling the second day trying to figure out the OSD. I have the Uart 4 for msp in the ports and still have no osd. Can you help please?
Hei Man, sure 😃
I struggled the same, i know your pain, but don’t worry, we will make it work, let’s talk on instagram, it is easier there :bilu.media
Great video , can I ask where you got those large instruction sheets? I will be building my first drone the Mario five shortly, but your video is very instructive to learn from.
Great tutorial!!!!!
Thank you man 🙏😊
Hi i recently purchased master 5 v2 frame, but as per manual i fixed front arm on forward facing of drone but i cant able to see holes 7:29. Forwad facing has long arm right.
Hi, maybe the v2 frame has different mounting? Or maybe it has a defect!
You can send me a picture of what you mean on instagram so i can see what is the solution for this. Bilu.media
I've watched so many drone tutorials for my first fpv build and a several for just the speedy bee master build and omg you are so much better at explaining things and you dont leave stuff out. Little details like the capacitor direction that no ever drone videos mentioned... and yes i should i guess have known that but didnt as a first time builder. I'm glad I found your video before I finished my build but I'm a little late and need to somehow undo this capacitor from my ECU =/ any advice?
Thank you very much for tour kind words, I really appreciate what you said and I am very happy that i could help you 😊!
I don’t understand what you did exactly with the capacitor! You put it in the wrong direction? I mean the minus on the plus? You can make a picture and send me on instagram so i can see and try to help you ! Bilu.media
Hello. So Thank You so much for this video. I just finished my master 5 build using your video. I have one issue. I can’t get sat lock!!! Are you having this issue. I’m using the bz-181 gps.
Hi my friend, my pleasure :) Did you make the necessary settings for the GPS in BF? I didn't show all the steps here, you have to select the GPS from the configuration tab in BF and in the ports tab you have to select GPS for the UART that you are using for that GPS! and after that you have to go to the Fail Safe tab and define how you want your drone to behave when it enter a fail safe situation ! I ended up not using the GPS because I don't fly so far with it, I am building a 7 inch drone and it has GPS! and there is a trick to get satellie lock faster, you have to wrap the gps wire in cupper foil and attach a black wire to that foil and connected to the ground wire together from the GPS, but make sure to wrap that coil afte intor a cloth tape or an electrical tape because it is conductive!tell me if you figure it out please
@@bilumedia Thank You for the reply. I have narrowed it down to ELRS interference. I move the GPS away from the ELRS receiver and antenna that are both sitting in the back and inside my house I get 18 sat locked! I tested it out with the gps zip tied to the front of the quad and I had 23 sat locked. So it’s definitely something to do with the ELRS antenna or RX.
@@emafpv glad that it worked after all 👍. happy flying 🛩
Do you fixs these drones? Because I have one that a friend gave me and I can't figure out what is wrong with it. I would like to try to fly it. If you can get back to me thank you.
Sure, lets talk on instagram : bilu.media
عاش يا نجم
حبيبي الله يسعدك😊
Im currently building this.. little by little.
I bought the V2 version. Very nice drone. I will have to buy a different GPS mount as it comes with a 181 mount and i bought the 880 gps.
The V2 already comes with the GoPro mount in the box.
i got v2 as well. did you have the same issue with camera cable?
@@andreikaliachka279 I am not using the DJI O3 unit.. I am building it with a Foxeer Trex Micro camera, and a Foxeer Extreme 2.5w VTX.
DJI system is too expensive for me right now.
@@andreikaliachka279 the o3 is short by default, in the video i changed it to a longer one ! So you need to change it unfortunately, becarefull how you take the cable out, i damaged the connection a little bit and i had to open the camera again, in the camera you have at the end of the connection a little mechanism that clicks, this one you have to pull out carefully 💪
If you have a printer you can easily modify it, i made my own parts for my custom made 3 inc whoop and for my foxeer foxwhoop 2,5
@@bilumedia yeah I have a 3d printer. I will have to create a custom rear end for it.. because I purchased the RP3 receiver that comes with 2 antennas and the default yellow TPU piece it comes with is for only one antenna.. the receiver TPU part is also interfering with the mmcx antenna connector of the VTX and I did not notice and selected the 181 GPS when I checked out the order and I had purchased the 880 GPS which is way bigger. So I'll have to redesign that rear end.
Hey, thanks for the video.I hate that mateksys BEC board. the pads of BEC ( in/out you had soldered ) easily peel off.
Hi, my pleasure 😊 ! Do you use flux? It helps a lot and the solder sticks very good and it never peels! Maybe your solder is not good too! I use 63/37 solder! So it should not peel at all, be careful because if it peels so easy you will loose your feed in your goggles and the crash is inevitable!
First of all, thanks so much for your video. It help me a lot. I have a question about motor, in speedybee website say it use 2306 1900kv but you use 2207 1750kv. Will it impact to performance? I cannot find 2306 motor here but 2207 are available so I wonder can I use 2207 instead. Thanks so much.
Hello, you are very welcome! Happy to help 😊
2306 is more for “cinematic” flight and 2207 is more for free style flight! But you wont feel the difference at all! You can use freely 2207 but be sure to be 6s, 1750 is 6s and 1950 is 6s too but it is a little bit less powerful bit not by much! So you are safe with 2207 👍
@@bilumedia Got it, thanks so much for very detail information.
@@jonathanoeijoeng you are very welcome, anytime 😊
👏👏👏👏
Thank you ☺️
I like it ❤
It is fantastic drone 🥰
Very nice Video!
Is it possible to connect the Dji Remote Controller 2 to this exact same build?
Sure you can do that! At some point if you see in the video I removed 4 wires from the cable that connects the dji air unit to the flight controller. The red and black are for powering the unit and the other 2 are actually for the sbus, so they are for using the dji rc2, and of course you will not need to solder the external elrs reciever as I did 😉
Thank you very much!
@@Peterlustig234442 my pleasure 😊
Building v2 of this frame up right now with an 03air i took off a bnf quad where it was mointed in tpu.. i saw you had a metal bracket to screw it down (this would be ideal with the new heatsink)..where did that come from please. Great tutorial helped me out getting back into building after a 7 year break
really happy that my vide helped you get back into building FPV 🥰! the heat sink is from the frame itself, there are a lot of heatsink for the o3 air unit in the market, some of them are generic and some specific a particular frame... for example the SpeedyBee Mario 5 that I will build soon on the channel has a Pro version with a very nice heatsink and it protects also the Air unit, you can check it here : bit.ly/42Bu2PD
Are you using v1 or v2 frame?
Hi, it is the V1 frame, but it is applicable to the V2 as well. I had a lot of people contacting me and the followed these steps, but for the V2 frame. Small differences is there of course 😊
What GPS is that?
this is the iFlight M8Q-5883 gps!
Great video! I have build mine after this video :) But i like to uppgrade FW to BF4.4. Can you do a video how to uppgrade FW? :) :)
Thank you, it is not hard at all! Maybe after new year i will do a short video about this 🤟
The Name of the Tubes is stand offs
Thanks 😁
Hi, great video. We are doing this build soon. what length cable did you use for the dji 03 air unit?
Great video!
Been looking at that frame but I can't tell if it has 30x30mm holes that allows to mount a HDZero Freestyle VTX. :)
Thanks my friend, actually it has :), i just measured the holes where is my O3 mounted and there are 30x30 holes too, you can see it here too :th-cam.com/users/shortslQhKrGesv-U , if you want me to measure or check anything for you, just say 👍
@@bilumedia thank you for checking!
It helped me alot. Atleast I know what frame and stack I will be using for my first drone build.
@@Daniel_SWE I am really happy that I could help you in some way 😊. This is why I did this channel, to connect with people and help them with what I can, because we are people and we should help each other not the other way around 💪
this video was very helpful thank you so much
i have couple questions this will be my first quad
i have dji rc2 but.. is elrs better? should i sell my rc2 and get a new remote for elrs?
SpeedyBee F7 V3 looks expensive... can i use cheaper stack for example SpeedyBee F405 V4?
You are very welcome :), did you build the drone or not yet? let's speak on instagram : bilu.media, we can talk easier and I can help you with all what you need 😊
Can we use hdzero Googles with dji 03 camera?..
Hello. No, Dji O3 system is only compatible with DJI goggles such as : Goggles2, Goggles V2 & Integra
Great video !
What accum did you use ?
You mean the lipo batteries?
I have a lot of them:
Cnhl 1400
Cnhl 1050
Iflight 1400
Gnb 1500
Gnb 1300
Gnb 1100
Gnb 4000 li-ion
All of them are 6s for this drone 😊
and im new to this build (and diy itself), I believe there are no capacitors in the frame box. I should buy it separately ? or it will come with batteries?@@bilumedia
@@andreikaliachka279 the capacitor comes usually with the stack(fc +esc), did you buy the stack or not yet? The speedybee stack comes with bigger capacitor, but be careful, don’t cut the legs of the capacitor short because you will have problems, actually the new frame doesn’t have a battery plug, right? If not then it is not a problem because the wires will not take all the place and you will have space to wire the capacitor, but put them first and see where they sit and after solder them, and be careful the capacitor to not touch the frame, it can make a short!
@@bilumedia wtf. I found a big bench of accessories in my f7 kit. It is much more fun then Lego
@@andreikaliachka279 😂 yeah it is a lot of fun, i love building drones, i want to transform my foxeer foxwhoop into an o3 drone and it is not made for this, it is challenging and i love this because i have to cut things to design tpu parts and it is a lot of fun, and a 7 inch drone is coming too, i am waiting for the frame, and i rebuilt my flywoo 2.0 drone woth a happy model mobula 8 😃, the video will come soon 💪
What was total cost?
only the drone is about 600 Euros and the goggles 2 850 Euros and the remote controller can start from 50 euros up to about 500 for a good one
Hello. I'm having a problem with uarts settings. I used dji rc2 so no additional receiver. Could you please teach me the correct uarts settings?
Hi my friend, you have to go the Receiver tab and select SBUS instead of CRSF because this is the correct protocol for the DJI RC2 and I hope you didn't cut the brown and yellow wires from the DJI air unit cable 😁 because they are for the comunication between the RC and the receiver on the air unit! tell me if that worked!
I have a complete step by step build video coming soon 👍
I finished my build and it flys really well! Thank you so much!@@bilumedia
Hello, I just finished this build. I'm at the step that I get all beeps properly. But when I disconnect the battery the vifly finder buzzer doesn't beep. Could it be that in needs to be charged somehow? Thanks.
Hi. So when you plug the battery it beeps, right? If this is the case then the unit is working, but when unplug it it doesn’t beep at all, this means that the battery is empty! It should work directly out of the box. I would fly a little bit, try at least 5 batteries and see after if something happens!
Edited response: I fixed it, I had messed up the + and - signs. It works fine now. Thanks for your help!
Radiomaster Tx16s kumandası yazılım sürümü kaç kullanıyorsunuz hangi sürümü tavsiye edersiniz acaba Türkiye'den selamlar
Hello, i have edge tx and i am
Using elrs 👍
How long the cable from the camera from vtx that you swap ?
Hi, mine is 14 cm, i am not sure how you measure it, i measured it from the back of the camera to the back of the air unit, so didn’t consider the parts that are in the units! But you can ask speedybee and they will tell you which one to use…
8:12 those are standoffs
Thanks 😁. Now I know, there are a lot of things that miss match like bolts and nuts . It is a mystery for me 😂
Hello Bilu, I follow your channel, I am a writer. I live in Brazil, presenting a lot with your videos. I'm building a drone of this model. Please clear my doubts. What is the reference of this GPS?
Hello my friend, thank you very much 😊, what you mean by the reference of the GPS? It is the iflight m8q-5883, but i recommend to use the new m10 gps instead of this one, iflight has it and few others too!
Hi! A question: I've built the same frame with the same stack (I haven't seen your video before I've put it all together. Unfortunately, it would save me a lot of time :))
But the stack mounting bolts are too long, so they protrude from the bottom. Seems stable, though...
Was it the same case for you?
Hi. You mean the screws are too long and there is a part remaining on top? If that is the case then yes, but under the esc i put another rubber grommet, but it is small ! You can send me a picture on instagram so is see what you mean : bilu.media
Is the battery strap included in the frame kit or did you buy it separately? If you bought it separately, what size is it? I bought this frame and I can not see this in the kit frame BOM list
Hello my friend. The strap comes with the frame, actually i think you get 2 straps! If you didn’t get it, please contact SpeedyBee and they will send you the straps 👍, the strap size is 250mm
@@bilumedia Thank you very much for the prompt reply. The frame kit is on its way, I just checked the materials list included in the kit and I didn't see the straps, it's good to know that they are included. Thank you so much.
Is F722 stack much better than F405 stack also from Speedybee ?
It is better yeah, but you don’t need that much power in most cases, f405 is very good 👍
will it be cheaper if I buy it ready for fly or if I buy it in parts and assemble it myself
It can be a little cheaper to build it, but mostly it is a must have skill to have in order to repair the drone after crashing…
Truly was necessary the larger coaxial wire for the 03?
Hi. Yes it is necessary, at least in version 1, maybe the v2 doesn’t need longer one!
👏👏👏👏👏🎮🚀💻🥽🪛🔧
Need to flash esc firmware?..or already..because 1 my motor not beep
It should work without flashing anything! Check your wires, maybe some wires are touching! You can send me a picture on instagram : bilu.media
U skipped the most important part the ports set up …….
You are absolutely right, my bad, sorry for that! If you need help with that part I can help you out ... I missed that completly in the edit !
@@bilumedia it’s ok brother you’re coverage is insane !!! I will be getting this quad end of month.
I just got a speedy bee f7 AIO and the dji port is inoperative and won’t pick up VTX on beta flight nor speedybee app :(
Thank you very much 😊! I just took a look at your AIO and it seems that DJI should be configured on UART 6, did you configure it like this? You can give me a picture of your ports on Instagram: bilu.media. Let's solve the issue and get you in the air 💪😀
Smoke stopper is a gimmick and doesnt actually work.
I guess you can connect a bettery and on the othe side connect 2 touching wires and see if the red light is on or not 😀
It saved me many times
music is such a pain I left at 30 seconds
Sorry for tour experience my friend, but this is how i create my videos for now… thanks for the feedback