I can't find a qualifying adjective to describe his splendid work. You learn only by watching your videos, thanks for sharing. Greetings from Montevideo, Uruguay.
When you can replace a clutch with your eyes closed, you know you're on top of your game. But combining it with martial arts, now that's taking it to another level. Can't touch this, man.🥷
Great video! I’m not a mechanic and managed to change my clutch following this video, so happy! Was quoted £900 by a garage. I bought a sachs clutch kit from GFS for £155 and £23 on 2L of Comma MVMTF Gear Oil 75W gearbox oil. Common socket sizes - 10mm, 13mm, 16mm, 18mm. Both 3/8th & 1/2” + extension bars & wobbly bits. Torx bits for trim and anti roll bar drop link. Mostly Halfords socket set. I did use an electric impact wrench aswell. Special tools - 17mm Alan/hex key for gearbox drain plug 9mm thin long socket for pressure plate. 36mm for axle nut 8mm long spline bit (tool station set) drive shaft 6mm Alan / hex bit (tool station set) internal drive shaft £10 cheap clutch alignment tool Red grease - rubber grease Black grease - high temp gasket sealant Couldn’t get passanger drive shaft out the hub so had to work around it disconnected from the gearbox. Couldn’t get the gearbox in, gearbox was fowling on the subframe. Had the engine height incorrect. Adjusted the jack and gearbox went straight in. Make sure clutch goes in the correct way round!! Be easy on the clutch for the first hundred miles. Took me 12 hours over 2 days. Would say 8-10 hours if you had no issues. Thanks again for the great video!
I just done a clutch on a a1 and had completely different gearbox to this 1 ,slave cylinder was built in to release bearing and the box was alot bigger than this 1
Hi,I find coincidentally your channel and i remarque that you work only outdoor on the vehicles.You dont need an warm and cozy Studio for working! Respekt and one subscription from Luxemburg👌👍🖖
So at 31:30…. What is been tightened / loosened when he puts the bell housing back on? Amazing vids… have to find the time now to watch them 😂 (helps when work is very quiet!)
A master class again & in real cold weather (even with the night heater) Noticed how you made life hard for yourself on the offside drive shaft as you placed the camera in the best position to suits us and not yourself. Why do you spin the tool up just before in goes onto the nut (?) Never used these neat tools myself that save so much time.
Glad you noticed that. 😆😁.. It does get a bit awkward how I have to position myself so it’s not in the way of the camera .. which part of the video you’re refer to .. spinning power tools. Is it to undo the clutch plate ..?
@@WMCS I believe he's referring to the 3/8" electric ratchet tool. Glad I'm not the only one noticing the finesse you have w/them. If I may - I think you do that so that the socket quickly seats on the nut/bolt rather than moving the tool around to do so.
Great work! Have you made any customisations via the one key app to any of the modes on your m18 impact wrench? If so, how do you have it set up? Just curious as you use it very well
I remember it clear as day. Was an old school Vauxhall vectra just under 200k miles .. up to about 6 years ago on average most cars was roughly 120-150i miles. Since then in average 60-90k miles or bigger ones and 40k miles on average smaller cars.
From what I've seen, I think usually for a standard flywheel, so long as it's still in decent shape he'll reuse it. If it's a dual mall flywheel I've always seen him replace them.
![Best 1.4 TFSi TSi Mods & Upgrades [Seat, Audi, VW, Skoda Tuning Guide]](http://i.ytimg.com/vi/_F9ex36vx7M/mqdefault.jpg)
www.williamsmobileclutch.co.uk 🇬🇧
Submit enquiry for price and repair date availability.
Thanks to our TH-cam customer for this repair.
I can't find a qualifying adjective to describe his splendid work. You learn only by watching your videos, thanks for sharing. Greetings from Montevideo, Uruguay.
Thankyou.
You are the best mechanic greetings from belgium 👍
Thankyou. And greetings to you as well
From mechanic to mechanic, awesome work mate 👌 you deliver a great service for people. Keep it up. Regards from the Netherlands
Thankyou.
Excelente trabajo, este es como mi coche me servirá para un futuro. Gracias 🤙🏼
When you can replace a clutch with your eyes closed, you know you're on top of your game. But combining it with martial arts, now that's taking it to another level. Can't touch this, man.🥷
😆😁.. always makes me laugh your reviews. Much appreciated
Awesome video as usual
Awesome video as usual ❤
The daddy of clutch replacement 👊
Bravo Kevin ottimo lavoro ottimo video in ogni particolare al prossimo un saluto Gek.
Fantastic job kev,well done bud,happy christmas and all the best for the new year sir
Thankyou Stephen. And happy new year 🥳
Top job well done mate 👍👍
Ciao kevin ,numero 1 buon anno
Great video! I’m not a mechanic and managed to change my clutch following this video, so happy! Was quoted £900 by a garage. I bought a sachs clutch kit from GFS for £155 and £23 on 2L of Comma MVMTF Gear Oil 75W gearbox oil.
Common socket sizes - 10mm, 13mm, 16mm, 18mm. Both 3/8th & 1/2” + extension bars & wobbly bits. Torx bits for trim and anti roll bar drop link. Mostly Halfords socket set. I did use an electric impact wrench aswell.
Special tools -
17mm Alan/hex key for gearbox drain plug
9mm thin long socket for pressure plate.
36mm for axle nut
8mm long spline bit (tool station set) drive shaft
6mm Alan / hex bit (tool station set) internal drive shaft
£10 cheap clutch alignment tool
Red grease - rubber grease
Black grease - high temp gasket sealant
Couldn’t get passanger drive shaft out the hub so had to work around it disconnected from the gearbox.
Couldn’t get the gearbox in, gearbox was fowling on the subframe. Had the engine height incorrect. Adjusted the jack and gearbox went straight in.
Make sure clutch goes in the correct way round!! Be easy on the clutch for the first hundred miles. Took me 12 hours over 2 days. Would say 8-10 hours if you had no issues. Thanks again for the great video!
I just done a clutch on a a1 and had completely different gearbox to this 1 ,slave cylinder was built in to release bearing and the box was alot bigger than this 1
Verry hard working g in this cold weather happy holidays and keep it save
Thankyou 🎄🎄🍻
sounds nice for a 1.4 , and that's a thumbs up from me buddy 👍🎄🎄
I’m definitely going to book you in. My car has done over 60k
Great job
Hi,I find coincidentally your channel and i remarque that you work only outdoor on the vehicles.You dont need an warm and cozy Studio for working! Respekt and one subscription from Luxemburg👌👍🖖
Thank you very much for subscribing 🍻🎄🍻
Робота супер ,префесіонал
have a good week my friend! 🍺
☕️ 🥐 🎄🌧️
@@WMCS 💪
Awesome man👌🏽
Can you tell me what is the exact name of the Milwaukee impact wrench and ratchet?
So at 31:30…. What is been tightened / loosened when he puts the bell housing back on?
Amazing vids… have to find the time now to watch them 😂 (helps when work is very quiet!)
good job
Very very great form Italy
A master class again & in real cold weather (even with the night heater)
Noticed how you made life hard for yourself on the offside drive shaft as you placed the camera in the best position to suits us and not yourself.
Why do you spin the tool up just before in goes onto the nut (?) Never used these neat tools myself that save so much time.
Glad you noticed that. 😆😁..
It does get a bit awkward how I have to position myself so it’s not in the way of the camera ..
which part of the video you’re refer to .. spinning power tools.
Is it to undo the clutch plate ..?
@@WMCS I believe he's referring to the 3/8" electric ratchet tool. Glad I'm not the only one noticing the finesse you have w/them. If I may - I think you do that so that the socket quickly seats on the nut/bolt rather than moving the tool around to do so.
Hi, Impressive :) clutch replacement. Need to get me them power tools. Question, what's the black sealant and red grease called?
Clutch master
Thanks
Thanks for the kind gesture. It’s been well received and very much appreciated.
Kind Rgds.
Kez.
Great work! Have you made any customisations via the one key app to any of the modes on your m18 impact wrench? If so, how do you have it set up? Just curious as you use it very well
Yes I do customise it to for different settings. I use 4 for degrees and 123 for nm of various strengths.
@@WMCS Interesting, thank you for your reply, what do you mean by degrees?😅
How much would it cost to replace the clutch? Including labor costs?
best regards William today plays argentinian from argentina best regards William
Viva Argentina 🇦🇷
Hi bro Amazing ! Whats product to clean clutch as brakes cleaner ? Thx
That’s correct. Brake/clutch cleaner.
Kevin what’s the oldest original clutch you’ve taken out of a vehicle and what was the highest mileage car you’ve worked on with the original clutch?
I remember it clear as day. Was an old school Vauxhall vectra just under 200k miles .. up to about 6 years ago on average most cars was roughly 120-150i miles.
Since then in average 60-90k miles or bigger ones and 40k miles on average smaller cars.
@@WMCS That’s a lot on it’s original clutch. I guess a lot of it is down to driving techniques.
Hai.👍
Fantastic lot of work how long did it take mate
Roughly about 3 hrs I think.
@@WMCS really good I’ve messed around with cars all my life old now lol
How long did the clutch replacement take Kevin?
This particular one can be done in about 3 hrs .. not too bad.
@@WMCS
Thanks for the info buddy
How do you determine beforhand wether or not the flywheel needs to be replaced? I see sometimes you change it and others you do not.
It's a solid flywheel on that Audi version so just a 3pc clutch kit needed
From what I've seen, I think usually for a standard flywheel, so long as it's still in decent shape he'll reuse it. If it's a dual mall flywheel I've always seen him replace them.
👍👍👍👍👍💪💪💪💪
Do you change on automatic 1.4 on this car?
Only manual gearbox.
Mate how many clutches do you in a day?
min 2. average about 4-5. this guy is a machine
👍👍👍👍👍👏👏👏👏👌👌👌👌🙂
Like, 🤙
Thankyou.
🎬📽🛠🔧⚙👍👍👍😉
09:57 Was that right tie rod off?
From the amount of rust on the thread I’d say it’s been off for well over a year.
@@WMCS No need to mention the broken back up sensor terminal wire.
Am I a fool or did u mean sway bar link. Driving without a tie rod is not really possible the tire would swing left and right.
Toyota rav4 año 2005
The front coil spring being unseated on full droop is a bit concerning! That needs helper springs.
James that is a coil over ..
@@WMCS I know mate, but it shouldn't be loose from the top mount like that. It should be seated against the top mount at all times.
Not on coilovers.
and I thought changing the plugs on my Subaru was a pain in the...
aren't those 1.4 tfsi engines known as one the most unreliable engines ever made
Not as far as I’m aware.
I know the very early VW golf ones used to have issues with the plastic chain guides. But that was recalled.
You're probably thinking of the earlier 1.4 TSI twincharger EA111 with the oil consumption issues.
😁👍👍👍 habe ich vor zwei Wochen auch gemacht 😁👍
Excellent.. I’m two weeks behind 🍻🎄😆