Finally, A cheap fix for the ford mondeo mk5 inner cv joint, bearings available online .
ฝัง
- เผยแพร่เมื่อ 1 ส.ค. 2022
- Alan Howatt Thanks Alan, could you say it on a video to inform people? Part No 2116-CA220 Brand is Febest. Now mine is the 2.0l tdci 2015 6 speed, Manual box, i think the shaft is different on the 1.5tdci. Cheers.
www.ebay.co.uk/itm/1945539197... - ยานยนต์และพาหนะ
![[4K] TREASURE(트레저) “KING KONG” Band LIVE Concert 킹콩은 라이브를 찢어🦍 [it’s KPOP LIVE 잇츠라이브]](http://i.ytimg.com/vi/p8bLLOxPDD8/mqdefault.jpg)
That Monika is getting too 'cheeky' Alan ! 😜🤣
I'm going to start calling Monika "SpannerEyes", cos every time I see them, me nuts tighten. 👍
Not a grease expert here but just to share what I know.
For the inner joint the needle bearing loading and speed characteristics is different. So the inner joint uses a 'bearing grease' while the outer CV joint (which has ball bearings and the load are concentrated on two points on the bearing) needs to have 'EP grease' (extreme pressure) which has molybdenum disulphide added for the protection properties.
And regarding mixing - for outer joint if non- EP grease is used then you would expect the CV joint to fail much sooner due to inadequate protection, on the other hand if EP grease is used for the inner joint it's generally accepted as the difference is really negligible.
If inner joints are regularly failing, maybe the cheaper grease is the cause? I wonder what the failure rate would have been with EP grease...
@@simontist More likely to do with the joint design - probably a bit underengineered but that's nothing we can do, other than clean up the whole thing as much as possible, having only fresh grease and hope it would last.
I've watched a good few of his videos. Brilliant mechanic. Saved a fortune on my own Mondeo.
I think everyone was happy shortly after that video started 🤣
Already replaced the entire shaft on my mk4 :(. Also a pain to diagnose these...mine was clunking at low speed when lifting off the throttle, garage initially replaced wheel bearing and outer joint, there was some slack in the bearing splines but the clunking came back after some time. Nearly replaced my bloody gear box as the sound was resonating in the gearbox housing, but finally a mechanic decided it's the inner joint, can't buy it alone so replaced the entire shaft. Problem solved but bloody hell...bearing, outer joint and then entire shaft replaced, when it could have cost so little.
20,589 views Aug 2, 2022
Alan Howatt Thanks Alan, could you say it on a video to inform people? Part No 2116-CA220 Brand is Febest. Now mine is the 2.0l tdci 2015 6 speed, Manual box, i think the shaft is different on the 1.5tdci. Cheers.
In what way is it different mate?
Alan. Yet another great tip for my next high mileage Mondeo taxi with transmission judder. Brilliant,
Great tip Monika, Alan and Rob, Thank You👍😎
Well done to both of you for sharing that info, it will help so many people to save a few quid. Regards from Galway 😉👍🍻💚 💙💛
Loved Monnie in this I want to own things and be happy, ps give her her sunglasses back 🤣
Cheers Alan (and Rob). Fitted this bearing yesterday. Still only £40 on eBay :)
i could completely eliminate the very, very bad vibration on my s-max only by turning the joint 120° in the housing. it was only supposed to be used for troubleshooting, but it has now lasted for several thousand kilometres.
All good information thanks Rob & Alan
Great video Alan, love the end shot with the drone 👍
Morning Alan. It’s fantastic people share their knowledge with you the best mondingo fixer ever 🤣
Thanks for sharing the tip Alan! 👍
Who's Martin Lewis?? Alan and Rob are the new money saving experts 🤑🤑
Spanners & Smiles, Ur a good bloke Alan 👍👍
Hi Alan 👋. Thanks for sharing that's good to know they fit the mk4 too .cheers 😀
Thanks Alan for your fast last reply,as I said before iam travelling back from southern Spain (Almeria), now my engine light came on in the last 300 miles since the start of the journey. Iam now in barcalona 1400 miles to go fingers crossed 🤞 sounds like the boost pipe tear but it's still running fine
Fanks, Rob.
Thats brilliant Alan thank you.
Loving the sneaky creepy Klaus reference, as always great work - cheers keep it up :)
Allen
Great money saving tip I bet their is a C V Joint out their on a other maje and model cat that would fit and save people a fortune but how would you find this Info out like this video
Phil in stoke
Well done Alan. Good advice
Always greate to see sweet Monika 😊👍
nice one alan, see ya
Nice nice.. and great crane video.
Oh Alan for the first time i seen one of your taxis in Luton airport other week. :)
Probably something to do with train strikes people getting taxi's all over the place so they don't miss flights or appointments.
I’ve seen them many times in Hertfordshire, once even in Central London too
Look like that part fits the SMax also which would probably do the galaxy aswell👍
Need to find the tripod joint for the mk2 focus st as that will be a huge saver too
I confurm. Very good solution. Thank you!
Good job ,hubby ! Muahhh 💋
Thanks for the important video and thanks for the informant. I checked the comments but did not find whether this joint or something similar fits to Mk3 Duratec he 1,8 / 2,0 litre?
On my 1.5tdci 2016 mk5 mondeo same driveshafts, same bearings and probably same gearbox. Flywheel is smaller and got 6 bolts instead of 8 on 2.0tdci
Top info as always my pal.
I was looking for a cigarette lighter plug in halogen floodlight that I had stolen with the car, finally found the exact ones on a boating accessories site not on eBay or Amazon ? Good for finding addresses at night.
Thankyou Alan 👍
Fair play finding that saving but won’t the coupling wear also so the bearings will move about inside but for £40 it’s worth saving till you can save for the complete shaft
long time ago, ford escorts brought out these inner "tri-pod" joints as they were called, they had cv grease in, + used to dry out, giving a steering shake. did quite a few under warranty
monny at the start, large erection at the end, what would sigmund freud tell us about that....
PS give her the 'glasses back
Alan - have you come across peeling leather on steering wheel and any fixes ?
THANKIOU
Love it.
Yeah plenty of stuff that you cannot find on Amazon or eBay Yet is available, sometimes your not putting in the description of the product the algorithms catch on to or looking in the wrong section, some companies don't sell on there either because probably mainly sell trade.
Hi
Can you show me how much play this tripod has in the joint cup?
I have a problem with knocking when shifting from 1 to 2. I have exactly the same joints in the Volvo.
Hi Alan, can you check Febi Bilstein 19945 bearing, it seems right?
How can you tell the difference between a DMF failure and Bearing failure?
Hi Alan, would this bearing fit a 2016 Mondeo, the reason for asking, the company that supplies these cannot verify they will fit and suggest I measure my old bearing, I do not fancy stripping out the drive shaft and dismantling the bearings only to find out they don't fit. Great video's, Kind regards
Nice thanks
Grease in the joint and bearings is divergent to the grease in the boot.
Well I hope all those people who were saying you put the grease in the wrong spot (in the boot) last time you did that job were watching. 😀
Thanks
Hi Alan! Can i ask you a question because u are the dady of ford ,and nobody can fix my problem here. I have a mk4 1.8 tdci and my problem its a hard start after the car sits for sevral hors . I changed fuel filter i make sure that the gasket sits proper, i changed the crank sensors ,cheked injectors and all good. First simtoms was hard start on warm engine ,now its geting bad to worse. When i parc the car width the front up its starts for 10 seconds and it cuts. I have to crank it for sevral times to start . Can u give me an advice what to chek furder because i have no erors on bord. Thank you!
thanks for the tip i will tell the son in law thanks for the video
cheers eddie
Do most of your videos apply to the 1.5 mondeo aswell mate
Hi Alan, great video! Thank you!
Just a quick question, would the same bearing fit both side driveshafts? MK5 2.0L. I'm going to try this method but wanted to do both sides. Cheers!
these bearings will fit both driveshafts but only the inner joints
Good evening Mr. Howatt !
I need some input on a problem my 2017 2L petrol 240hp Mk5 has.
The car is pulling to the right when I let go of the steering wheel ( and pretty badly) after 9 alignments in total on 2 different stands.
This occurs on 3 different sets of wheels, 1 set being brand new tyres I put on today which didn't help either.
I've done both inner CV joints because I thought they have excess play, also didn't help.
Brakes have been all renewed ,no caliper sticking.
Wheel bearings are all good.
Suspension is tight,nothing worn out as far as I can see.
Engine mounts aren't leaking, no excess play.
I've noticed that when I put the wheel straight and look at the Steering angle sensor value it says -2° which is odd imo. But shouldn't influence the physical alignment at all.
I've messed with the PSCM , tried turning every assisting function off and back on with no change. ( pull drift compensation etc.)
I'm at a loss here and feel like I've checked everything, expect replacing the steering rack.
I feel your pain. Even the professionals don't always get it right first time . Have a look at suspension top mounts
Hi
Is it exactly the same part for both sides of car? I have similar issue but on passengers side
What's with the Jaqueline Onassis sunglasses? 😁
Does anyone know if these also fit in the same place on the VOLVO C30 D5 shaft , they look identical and the cars share a lot of parts.
You pinched monikas sunglasses you naughty boy 😂
Would you fancy another st220 on the channel alan
Hi Alan I’m in need of some help my mondeo estate mk4 needs a man like you with the expertise of mondeos! Engine management light has come on and faults are leading to dpf I’ve had this changed but lights are back on again any ideas or help would be greatly appreciated
Hi,my name is Toni from Romania,please tell what is the writing order of installing injectors in ECU at ford mondeo mk4 ,2.0 tdci...I know the order is 1 3 4 2...not in cilinder order...but I am not sure....thank you!
Any grease is better than no lubricant. Try something exotic like goose fat!!!
Stavros
Will this fit on a 2015 focus st tdci?
Is it okay for 1.5 ecoboost 160 hp? Thanks.
Hi Alan I spy some motor parts direct invoices on the wall lol I am a driver for them in cannock Staffordshire
Today £40, Tomorrow £250 when Febest find out.
Hi Alan off topic mk3 petrol mondeo 2.0 73 thousand miles good history is it a big job just change timing chain tensioner I no chain is good but tensioner breaks down what you think
you buy the chain and tensioner as a kit... many motor factors sell them now, for the time and effort to get to the tensioner it would be best to fit a new chain as well... th-cam.com/video/6_n-AiBki44/w-d-xo.html
Hello Alan, how much lubricant do you use on the internal CV joint (bearings and box)?
Compliments
the cv joints have a couple of packets of grease per joint from dry and the gearbox is about 2 litres
I bought a package like this that comes with 90g of lubricating grease and I found it to be a small quantity. Hence my question 👍
One more question, do you know where I can purchase the Mondeo mk5 Torque specifications?
cheap fix more good
Alan any tips for aligning the inner joint bearing into the cup?! You made it look so easy but I’ve been an hour now and can’t get it to fit at all? 🤔🤔
well you lower the bearings onto the cup and try jiggling each bearing at a time towards the outer edge of the cup until it drops in...they are a bit fiddly but once you get the hang of it you will do it no problem...its a case of keeping the bearings level as you jiggle it into the cup
@@alan4x Thanks for your reply mate. I decided that in the end as it seemed no matter how hard I tried (I’d been at it an hour and a half when I messaged you!) they just weren’t for going in so out came the big persuader and low and behold…… in Barry Betthel style “one bang and they were in” Lol!! Car all done, including a new track rod end, and all happy!! Catch ya 👍🏻😎
@@RATTLER238 thats great, i didn't ask if your car is mk4 or mk5...on the mk4 you have to hit the bearings into the cup but on the mk5 they slide straight in
@@alan4x Mk4 mate! Every day’s a learning day 👍🏻😎
Please help again with the links. Those are not available.
A Tip and just the tip I’m sure many are thinking it 😆
Alan is deffo sticking it in Monika
Yeah big difference between £350 and £40 and that's the cost of parts if correctly diagnosed!
🤣👍
Wonder if you get a cease and desist from fords anti right to repair muppets.
I wonder how is that Monica is still there and you didn't sent her home after brexit...