The Secret To Perfect Moulding Returns(Wish I Knew This When I Started)
ฝัง
- เผยแพร่เมื่อ 8 ก.ย. 2022
- If you try out this technique it will immediately become your go to method!
Glue used in the video: amzn.to/3d04Qgq
Accelerator: amzn.to/3d1Zv89
The Links above are affiliate- a great way to support the channel.
Thanks for watching! - แนวปฏิบัติและการใช้ชีวิต
![ทัศนศึกษาโรงงานผลิตโค้ก [THAI/ENG SUB]](http://i.ytimg.com/vi/M9y-TJBNem0/mqdefault.jpg)
![[TH] VCT Pacific Stage 2 - Week 1 Day 1 // DRX vs ZETA | BLD vs TS](http://i.ytimg.com/vi/AWaOqaxN6Y0/mqdefault.jpg)
I find that CA glue is great at transferring my finger prints to my work piece...:)
😂 Me too!
I always manage to forget not to scratch wherever I itch when I get CA glue on my fingers. It can get pretty embarrassing.
😂💯
Most times I forget and pick my nose. Hate it when THAT happens . Butt this one time....
After a couple screw-ups I won't open a bottle of CA without gloves on.
This man is the woodworking version of Bob Ross his voice is both educational and soothing
You've got great content, and a great on-camera demeanor. Thanks for your contribution to the repair/remodel youtube realm.
Thanks Stephen, that’s great if you to say🍻
@@TheFunnyCarpenter ❤
Recently bought a new house and have been doing some remodeling. I am an amateur but about 20 years ago some of my early jobs were construction so I have some skill. Anyway just wanted to say that I have found your videos very helpful for tips and bringing back some of that forgotten knowledge. Thanks.
Tip for using the super glue. You can use it without the activator initially for more working time. I oftentimes will put glue on, put the pieces together and hold for about 10 seconds, then spray the back side with the activator. With MDF especially, the activator will soak the material and activate the glue. Even without the activator, the cyanoacrylate glue will bond with a bit more time and be just as strong.
Been doing similar for years; I usually make the return longer, glue in place using tape to fold into place, then trim and finish the stub to be flush with the back of the moulding. Easier than fiddling around with tiny (and fragile) pieces.
So amazingly helpful! thank you. I am planning to make a semi complicated box to make our plant drape in a really pretty way and this will make it look beautiful!
I really enjoy your videos and learn some great tips from them and reading the comments. Love your simple no hype style . Well done from an Australian 😊
Used CA doing my baseboards and other trim. Works like a champ! Used it to apply the skins to my new kitchen cabinets as well. Thanks for reminding me to buy a new blade for the miter saw. 👍🏼
Cheers Harry. It’s always nice to have a couple blades and then when you’re cutting roof shingles you can put the old one back on😂
I love watching your videos and the way you explain things! Have a home remodel project and I’ll be be referring back to quite a few of them as I go. Thank you so much for them! 😊❤️
Thanks for watching!
Great tip. But "no fancy tools required" . I'd say a sliding compound miter saw is a fairly fancy bit of kit. Best purchase I've made in awhile and it's paid for it'self many times over.
Nicely, clearly explained. No nonsense, nicely videos. Thank you
This was so helpful. I wish I could havre irked with someone like you years ago. You are an excellent instructor.
There is actually another option thats a variant of your preferred self return. Instead of a 90 deg/square return, you can do a 45 degree version where the baseboard appears flows into the wall. It is particularly useful when you want to terminate at a thinner material such as tile. I can't take credit for this one - learned it from the legend Gary Katz
Is there a video on how to do it that way?
@@PhongNguyen-df9bt "Installing Baseboard: Program 4, with Gary Katz" on TH-cam. 49 minute mark.
@@Reflekt3D Thanks a lot, I now have a new series of carpentry videos to watch
@@PhongNguyen-df9bt it's easy you just use 22.5 degrees for your miter and start with a 45 instead of a 90. This is the way I do it for every piece of shoe i have to end. Also crown that has to end, I don't do like in this video with a 90 degree return. I think you see the profile better when it's angled and that detail is very appealing to me
th-cam.com/video/R6FDzusxkx8/w-d-xo.html
I've used a hot glue gun since the 1970s for all trim returns . Thanks for Your insights . Good info for Us all .
This guy is absolutely on of the best in his craft. Explained perfectly well. I am confident I can try and attempt this at home now.
Thanks Glenn, I appreciate the praise.
Brand new subscriber here from Fall River, Massachusetts! I often wondered how to do those returns! Thanks a lot for your video! 🇺🇦🇺🇸🤜
I would note, that I find it vastly easier not to cut all the way through on my return blocks. Those tiny little 45 degree triangles tend to get thrown all over when you cut them completely through, particularly if you are cutting them on the miter and not the bevel, as shown here, and often ruined when the blade catches them. I find it much easier just to leave the back bottom corner in place when cutting, and then you can break them off easily, and trim off anything you may need to with your utility knife.
Also, when doing this at scale, I recommend building your returns and joins on the backside of another piece of baseboard from somewhere else in the install. This way, the extra glue doesn't get anywhere you care about, and you can use activator to neutralize any drip through, and not worry about messing up any part of the house you are working in. It's also flat, and long enough that you can force the baseboard flat when doing long joints to make sure the joint closes properly.
Nice tips, thanks
Good tips
An extra piece of wood behind the base will stop the small return from slingshotting into the atmosphere.
Excellent video. Few things that help me. Always keep a small cup of warm water and keep dipping your finger in the water. Also when you have caulk in your finger, just wipe it on the back of your opposite hand. It's my painter's pallette. I reuse in spots needed. Less waste also. Keep up the good work
Will need this tip when I redo the living room as it leads to the hallway. Love the details. Keep ‘em coming.
Great teacher, the way you describes the working process is really relaxing and crystal clear good stuff，，👍👍👍
One tip I would add to this is putting a wood backer on your miter fence that will keep the piece from being kicked by the blade. This also has the added benefit of stopping tear out on the cut exit.
I use two pieces of .25in x 1.5in x 12in on each side of my fence with a little double sided tape to hold it on. This makes those small cuts so much easier to do with far fewer messed up pieces. So many times I've had tiny pieces get grabbed by the miter saw blade and thrown at 100mph, but having that gap closed with the temporary wooden fence that closes the large gap of the permanent fence solves that issue.
Excellent point on the sacrificial fence
That is what I always do. Especially useful when cutting small pieces of oak trim, as the blade kick them out much more often than softer materials.
God dammit! All these years running trim and I didn’t think of this cut! Thanks dude
Great video.. It took me a while to learn this technique; as DIY we don’t do it on the daily. However, if you do end up with a bit of a gap, I use DAP spackle and clean it up with a damp sponge.. It works well..
Great tip!
What a brilliant video and exactly what I need for a job I have to do.
Good video. I actually like the 2nd option you showed for the application by the stairs. Just my opinion. Thanks.
Really good tips! Thank you.🙂
To line them up for glueing, use a straight edge and butt the workpiece against it so when you add the other one just slide it down the straight edge then push into place. Perfect fit!
Nice tip!
Excellent video! Except I have to respectfully disagree with the turn down return looking good at all. Never got that at all. Love your approach to safety for cutting the turn in return without over doing it. There are new folks watching and it’s important to help them keep their fingers intact. The gluing techniques are spot on! Your out takes at the end are MONEY! Especially the Minn-esotan one! 🤣🤣🤣Thanks for the info and the chuckle!
LOVE THE DETAIL ................ COVERING ALL THE DO AND DON'TS . most others only generalize THANK YOU !!!!!!
Hi, I love your videos. You are incredibly informative and you make it entertaining. I had a quick question. I have a bunch of french doors with very short runs of baseboard in between. I was wondering if it would be lame to just use the router to 1/4 round off the edge of the baseboard as a return instead of cutting 1000 little pieces for returns. Thanks
Nicely done, or as I used to do mitre the end then with a coping saw cut following the profile, then a light sand up , no dangerous tiny slithers.
Nice trick! Thanks, enjoyed watching.
What a great teacher!
Great instructional video, for those who don’t know how to do this.
Whoever did my house before I bought it did something I really like and never would have thought of, return in a post an inch or two taller than the base. Looks like a tiny obelisk. Really cool in my opinion and not too difficult to make a ton of them and toss them in.
Great video, many thanks!
Learnt some great new tips!
Thanks mike🍻🔥
Love the turn down idea....never seen that before.
On site we cut the return 45 into the wall an inch or two bigger than it needs to be which makes it easier to hold and place whilst gluing it up. Once set just use a handsaw and run it flush down back of the skirting and cut the excess off. There is also a 4th option which is to return the mitre into the wall using 22.5 which gives a 3 piece return into the wall,it is more work and more fiddly but it does look the best .
I made good experience with acrylic caulking for glue. It takes a day to cure, but it looks nice and doesn't stick my finger to the wall.
This is pretty much exactly how I do them too, you hit the important points!
Thanks for checking out the vid
You're a highly skilled man, both in terms of doing the work, but also explaining it. THANK YOU!!!
It's all in the Festool saw, make no mistake bout it.
Excellent as always. Thank you
Unfortunately I only have an old Craftsman chop saw, but I got it for free from family, so can't complain. But I did get a diablo finish blade, 80 teeth I think, which does super clean cuts. Using painters tape over a cut can help prevent tear-out as well I think. I also had to try to calibrate my saw so it was square at to 0° mark. If either cut is off by the smallest amount the return will look like crap. I cut a ton of returns for door casing headers. CA glue + activator worked great, and any minor seams I filled with white wood filler, sanded, primed, painted. A lot of work for something no one will notice haha, but looks perfect to me! Baseboards next!
Best wishes on the baseboards🍻
Wow 🤩
I have never come across this method before
Awesome 💪
Great vid, would add that you can set your saw on a slight bevel to ensure that return piece sits nice and tight to the wall. Learned to use glue/activator from your for miter vid and haven't gone back!
good tip
We carpenters call that a "relief" cut.
Nice job. Two off and I go into a house and see somebody did it just a square cut absolutely unacceptable unless the homeowner Did it himself I myself don’t have the luxury of that nice slide saw but I manage I have been using wood glue and tape but the glue you’re using looks pretty slick thanks for posting
This works on decent size mouldings and on MDF. We use 11mm thick skirt and arch. It would still be possible but return is tiny. Plus CA glue not so good on pine. Which is our most common material. It is neat on what you use though.
I built staircases, and usually got the millwork installation too. Before that, like most, I packed lumber and framed.
Framers want to kill you in the winter, when they see through the windows in your stocking feet, ticky tackin up all of that beautiful light wood/mdf. I would tell them that “the instructions are in boxes that my parts are shipped to me in”. That’s how I learned, I taught several, friends for life.
“Thank for teaching”. (The old ones, taught me the most.)
If your a carpenter doing finish trim invest in a "Hot Glue" gun,,that works great and no need for nails,,perfect joint every time
didn't know about the sliding aspect.. Thnks!
Tanks, you are very professional
🤝
I never even though about this. Nice video, a detail I've never noticed
good video. would like to see one on the different glues you use.
Thank you for this video!
Nice job sir, thanks!
Good tips, nice job
Great knowledge. TFC is a master of his trade
I agree and nicely demonstrated 🙏
Thanks buddy🍻
Damn, that's beautiful. Great video. Question - what slide saw are you using? That was very smooth.
In situations where I need to be certain about placement of glued pieces I forgo using the accelerator. I do a test with the brand I have on hand to be sure it eventually hardens.
Alright, alright, fine. You convinced me to subscribe.
I like to use a piece of tape to hold the return to the saw surface so it doesn't fly away after cutting. And if your return is a little heavy, you can stand the piece up and run it through a table saw set to the thickness of the trim to cut the back edge of the return to proper thickness
I love the that saw had one at my last job best for finish work
CA glue is amazing…I can’t believe I only learned about it recently.
Honestly the bottom straight 90 cut in the thumbnail looks just fine and the best to me.
Great video Thx! White glue is a heck of a lot safer if you don't have adequate ventilation.. read the warnings on the activator can Bro!
Great video 👍🏾 👍🏾
BSI (Bob Smith Industries) makes good CA as well. Good variety of products and solid applicators.
Fine finishing work is difficult for me. Thanks for the secrets. Subbed
Thanks Andy🍻
Sweet! Making pros out of us amateurs!
A couple times I made the return too long but with a small moulding with a good flat on the face I could trim it flush with the back at the table saw.
I would love to hang out with this man for a week.
Thank for the video
Tip: Don't worry about cutting the return piece to perfect length! Let it be a little bit long. Glue it to the main piece, trim to fit, possibly with a sander, then attach it to the wall.
Thanks for the tip!!!
I love these returns, and use them as often as I can! For some reason I call / think of them as ‘blind returns’, don’t ask me why.
I opt for the masking tape and wood glue method, works well usually, but nothing like as quick as CA granted
I think they are also called blind returns.
I use wood glue (Pattex D3 ). Works like a charm, allows for corrections and dries within half an hour.
“No fancy tools required” …uses a Festool chop saw.
If your saw allows for the space I like to use a make to prevent the little piece getting flung across the room.
Thanks for the advice. Please tell me what brand slide miter saw you have in this video. I prefer the pistol grip. Thanks!
Nice job!
Such a great video bud! Here in the Netherlands its not usual to use moulding because the walls are made of brick or gyporock but i always love the look of moulding and i really wanna start using it in projects, some great tips as always bud! Expecially the CA glue i really need that. Have a great weekend bud🍻🍻
Thanks buddy. I would recommend messing around with the ca glue. It’s handy for a lot of different things.
@@TheFunnyCarpenter thanks bud! I will do tgat 4 sure !!
On MDF I wet the joints with a damp sponge. This stops the glue and activator from soaking in. Always works, never had a problem and the joint is strong. You use less glue and activator. Its cleaner as well. Try it out on a scrap piece you will always use it.
Saving this video!
As a contractor myself, I don’t know what cheap customer is going to pay for the time and money it takes to do a return like this. The easiest way I do returns is just using a palm sander to round the edge. I do have to repaint it but it’s just more cost effective. Sadly most customers don’t appreciate or want to pay for a nice return method like this in the video.
The video was 8 minutes long and obviously padded out because it is instructional. Let's guess at 5 minutes each. If you premake all your ends maybe less. If you've 20 to do in a house that less than 2 hours.
If your customers can't stand an hour or two to make 20 skirting ends look classy instead of shit then you need new customers.
I prefer wood glue and a couple really short 23ga, and yeah, assemble on a flat surface before putting on the wall.
A lot easier in a workshop. Where as on price work with a pencil sqr a ruler and handsaw. Then either no nails, hitting nails or a drill plugs and screws to fit it to the wall. Plus a saw bench. Or lugging a cross cut saw around the site. It's a good idea to carry a tub of putty to fill gaps in the joint. Otherwise the painter will just use caulk.
Well done 👍
good video. ith the gluing whats the spray applicator actually do?
Thanks Funny Man. Another great tip.
🍻cheers Jim
I prefer a 45 degree angle finished end where the little piece is cut at an angle on both ends (22 1/2 and 45 degrees) and the main piece is backcut ( 22 1/2 degrees). Takes more attempts to get perfect but lots high end and works great for thicker baseboard terminating at thinner door trim. I do it a lot with the shoe molding since it often extends out more than the door trim.
Interesting. I'll try this out...
When I cut the returns, I like to try to time shutting off the saw so that the blade is almost stopped as it finishes the cut and keep the blade below the surface of the cutting surface. That way the piece doesn't vibrate or slip into the blade and launch out. Then you're cutting a new piece and not having it possibly thrown back at you
Fantastic!
You are legend.
Great content and awesome technique, but if you don't think a Festool Kapex slide saw isn't fancy, then Id love to know your thoughts on what is.
“Same blade for the last 15 yrs!” Cracked me up! 😂. Ummm yeah
Or pretty close lol 😉Thanks!!
Great job god bless
Square cut looks the best for sure
This is a fantastic video!!!!
Thank u
Great tip. Thanks for sharing your knowledge. Kid must be back in school. Your "Funny" coefficient has gone back up.
It was a glorious week!