D.I.Y Custom Tinny Build COMPLETED! - Part 2 of 2!
ฝัง
- เผยแพร่เมื่อ 2 ต.ค. 2024
- Here is part 2 of our Stacer Territory build, if you missed, part 1 be sure to check it out in the link below!
• D.I.Y Custom Tinny Bui...
Don't forget to like the video and subscribe to help support our channel and follow our new adventures!
ignoretherust
ignoretherust
I’ve done a lot of boat mods over the years…currently in the process of rethinking my whole set up. I really like what you’re doing, and without welding…😎👍
Really enjoyed this build.
Great jerb. About due to replace my plywood/carpet floor of my tinny. So, I'll be interested to see how your alli/carpet holds up.
Cool build. One suggestion: instead of the foam and then screwing the floor down you could use 3M VHB double sided tape. Super strong. I've used it for offroad trailer floors and it sticks like nothing else. No need for fasteners and it would do the same job as the foam as well. You only get one chance when gluing the sheet down though.
Why do you silicon the rivets?
Mate I boat build for a living and i tell you that this is pretty damn impressive. I dont know how much all that aluminium cost you but its great to see you took your time. Well done mate.
Thanks for the kind words mate🍻
Totally agree what a professional job hey .
dude sick! need a follow up on how it goes for a weekend away
Hey mate, we did an overnighter to Hinchinbrook Island in it. Check it out. :)
Hi Jamie,
Thanks for the videos your posting. 3mm plate for the deck. What thickness did you use for the supporting angle/T pieces/ U sections? Also 3mm?
Regards
Hy Schoultzie, yes mate, everything was 3mm. Thanks for watching🤙
Great job mate. Looks mint 👌
Cheers Alfie, thanks for watching👍.
Pretty damn cool. I’ve watched heaps of tinny fit out vids, but this one is by far the coolest. Gives me some ideas for my tinny. Cheers
Thanks for watching, Miko!
Hey mate, thanks for sharing your build process. How’d you go about getting every bit of aluminium shavings out after drilling the holes for rivets? 😂 good to see you using tefgel between your (i assume stainless) rivets and the floor.
Well done looks great very neat also.
How have you found the riverts instead of welding any problems with them pulling or breaking.
What are the latches you also used for the lids are they lockable
It all been great. No movement at all. The latches are from Bunnings and they are lockable- they come with keys. :)
@Ignore The Rust thxs so much.
Once again excellent now enjoy all your hard work
You've done the best build 9n U toob bud well done inspirational and proffessional
Very impressive aluminum work! What is the thickness of the aluminum deck?
It's 3mm! :)
After a few hours of repairing holes in a new cheapy tinny. Im.glad to see you use tef gel and sikaflex.
The idiot b4 me put screws and rivets in holes. All that did was cause more corrosion.
Hey mate thickness plate did u use
Hey Blake, 3mm plate👍.
@@IgnoreTheRust legend. Smick build champ stuff the welder lol
@@IgnoreTheRust What livebait tank insert do you have? cheers
Mate bloody epic build and great content I’m about to do a build for my little cutter deluxe and you’ve given me so much ideas legend !! New sub from Hervey Bay :D
Still think it would be worth it to fit a rectifier to motor and run it to the battery to charge it .... really inexpensive to do yourself...the spare wires to do it will be there as part of the loom...👍
What a ripping job. Have been searching for a no weld option and now you have shown me how. Thanks heaps for sharing.
Thanks for watching Chris, good luck with yours! So far the deck is still holding up great!
Great boat
Great misses
Great dedication and planning
Great workmanship
Just loved watching this, inspirational, educational video mate, been ta Bunnings, apparently the young staff are unable to provide me with a ruler or tape capable of measuring a B's dik or a Nat's nakka, guess I'll have to guess.
Well done mate
Yes you need to insulate stainless and aluminium as long the cloth tape doesn’t hold water you’ll be right
A thin coat of silicone or mastic would have been better.
Nice job on tinny....gives me a few ideas when i start mine shortly cheers Paul from Melbourne
Bloke.. corepit.
Do you have any fuel gauge or how do you keep an eye on it being under the deck?
Hey mate, the tank has a dodgy gauge on top but I always fill the tank up before heading out (25L) and carry a spare 10L to be safe.
What knife holder is that? and where did you get it? thanks!
Hey mate! Got it at Road tech marine, it's a ripper!
nice work, what did the fit out end up costing you ? and is that an english accent you keep slipping into ?
Makes you wonder how far behind the manufacturers are in fitting out boats.
Should of painted the hinges black or grey
Hey mate, you got a rough idea of how many meters of ally you used for the framing
Fuckin beaut! Good stuff mate.
Thanks for watching mate.👍
Great work Jamie! Hope you fill that esky with some good fish 😎 🎣
Well done. What part of the world was shown in the water tests..Airlie Beach or Hinchinbrook?
Hi Ian, It's our back yard at Hinchinbrook!
Bloody awesome job guys. Looks the goods! 👍🏼
L I K E 👍 👍 👍 👍👍 🌟 ⭐ 🌟 ⭐ 🌟 🤩❣🤩❣🤩🤩
Great job - result well worth the time and patience.
Nice boat setup mate time to
Get Some
That's a great build mate 👍🏼
Great job bro !!What are the brackets holding the two seats ?? I need a couple
Hey mate, you can get them from Anaconda. They are Ok, they have some sideways movement even when tightened right up, but are fine for now. Thanks for watching!
Pretty mean build there bro! I'm just about about to do something similar to my new to me rig 😅 . I've got 2 questions for you,
1, what were you putting on the rivets? And 2 how have you found fuel vapour/smell with the tanks under the floor?
Hey mate, the stuff on the rivets is Tefgel/duralac which is a lanolin based gel which stops the reaction between two different metals. The fuel vapor hasn't been a problem, it isnt fully sealed in there as there is a ventilation gap under the rear seat to the transom. Thanks for watching!👍
@IgnoreTheRust cheers mate appreciate it 👍 🍻
Great job. Solid work🙌🏼
Greetings from the US. Nice job on the build. Here we have the Tiny Boat Nation (check him out on TH-cam).
What boat is that (manufacturer and size)? Is it going to be a car topper?
I don’t know how I missed it…a Stacer 389 Territory
Hey Chris, it's a Stacer territory 389 it's 4.1m long and 1.9m wide. Its too big for a car topper. We will just tow it along. 😊
Great job mate. She’s a beauty!
Well done great work.
Awesome build mate thanks for sharing! Do you recall the brand of the storage box in the seat, it looks great.
Thanks mate, it is the glovebox that came with the stacer from factory.👍
@@IgnoreTheRust cheers mate
Bloody good job Bunge
Job well done 👍🏻
Looks great
Absolutely beautiful my friend great work
Cheers mate, thanks for watching👍
Do the spacer in the carbie mate will be a 30hp then 👍
Already done it mate, she goes good!
Good work
Beautiful job = beautiful boat !!! Way to go...