EASILY Install Concealed Hinges / Comprehensive Guide / Euro Hinge / Cabinet Hinge / Vid
ฝัง
- เผยแพร่เมื่อ 15 เม.ย. 2023
- Hi everyone!
Welcome to another video.
In this one I'm showing you all the processes to fit a full overlay concealed hinge. This hinge is the most commonly used hinge.
I run through all the measurements you need and do a demo from start to finish.
It's really easy, why not give it a go!
ALUMINIUM HINGE JIG - www.banggood.com/custlink/3vKEQHIQgd
GTV SOFT CLOSE HINGES - amzn.to/3UFdrGw
I hope you enjoy!
If you found this video helpful, please leave a like and a comment.
Enjoy The Video
Ryan
If you liked the video or have learnt somthing from it, please Subscribe and Share.
Also leave a comment :-)
I also have a Membership you can join to support the channel (Link below)
If you like my content & would like to support the channel monetarily you could become a youtube member with really cool PERKS!
/ @thelondoncraftsmanwor...
Or directly via paypal:
PayPal.me/TLcraftsman
****SPRAY ROOM TOOLS & MATERIALS****
GRACO 695 ULTRAMAX 2 AIRLESS SPRAYER - amzn.to/2O7HDJp
GRACO 390 PC AIRLESS SPRAYER - amzn.to/2LX0Ufw
GRACO RAC X GUARD - amzn.to/34tVFuo
GRACO 110 FINE FINISH LOW PRESSURE TIP - amzn.to/2PRrrvO
GRACO 310 FINE FINISH LOW PRESSURE TIP - amzn.to/2PIMQHC
GRACO 410 FINE FINISH LOW PRESSURE TIP - amzn.to/2spuWSd
SPRAY BOOTH TURNTABLE - amzn.to/35oNj8v
SIP SPACE HEATER - amzn.to/30ADvq9
SPRAY FILTERS ON A ROLL - amzn.to/2TyIlTz
TWIN SLOT SHELVING UPRIGHTS - amzn.to/2uTXapl
TWIN SLOT SHELVING BRACKETS 10 PACK (370MM) - amzn.to/38l76H2
PIPE INSULATION (TO PROTECT SHELVING BRACKETS) - amzn.to/2tjUK37
400MM ADJ SPEED EXTRACTOR FANS - amzn.to/2TCfBJK
****BANGGOOD TOOLS ****
UPGRADED PARALLEL GUIDES - www.banggood.com/custlink/GmD...
ADJUSTABLE TRACK SAW SQUARE - www.banggood.com/custlink/mKv...
HONGDUI CHAMFER PLANE - www.banggood.com/custlink/mDm...
200MM CARPENTERS SQUARE - www.banggood.com/custlink/33K...
300MM PRECISION SQUARE - www.banggood.com/custlink/m3m...
300MM ANGLE T SQUARE - www.banggood.com/custlink/vmK...
600mm ROOFING/CARPENTER SQAURE - www.banggood.com/custlink/D3K...
PAIR OF BESSEY COPY WRATCHET CLAMPS - www.banggood.com/custlink/K3G...
PLUS MORE...
ALUMINIUM HINGE JIG - www.banggood.com/custlink/3vKEQHIQgd
POCKET COMPASS - www.banggood.com/custlink/333...
DRAWER/DOOR HANDLE JIG - www.banggood.com/custlink/KKv...
DRAWER/DOOR HANDLE JIG - www.banggood.com/custlink/3vv...
GUIDE TRACK SAW SQUARE (BUDGET) - www.banggood.com/custlink/KK3...
ATOMSTACK LASER - www.banggood.com/custlink/mDG...
****TREND TOOLS****
SMALL FINGER PULL CUTTER - amzn.to/3GAMaAh
MEDIUM FINGER PULL CUTTER - amzn.to/3EqsMD6 (USED IN THIS VIDEO)
LARGE FINGER PULL CUTTER - amzn.to/3OmNZmf
TREND ROUTER TABLE - amzn.to/3TS7Omz
TREND T14 ROUTER - amzn.to/3hZDkl1
TREND T35 HOOVER - amzn.to/3V9Q3jn
****OTHER WORKSHOP TOOLS****
HYUNDAI HY55 COMPRESSOR - amzn.to/3PwujMm
VIRUTEX AG98F EDGER - amzn.to/3MbHroc
PAINTABLE EDGING - amzn.to/3EniuTK
PAIR OF BESSEY COPY WRATCHET CLAMPS - www.banggood.com/custlink/K3G...
T - TRACKS AS SHOWN ON MY ULTIMATE WORKBENCH - amzn.to/37WKIJd
1.6MM RADIUS - MICRO ROUND CUTTER FOR 1/4" ROUTER TRIMMER - amzn.to/3cTCYW6
MAKITA ROUTER TRIMMER - amzn.to/3JNENDp
SANDING DISCS - amzn.to/2FZe1JI
MAKITA ORBITAL SANDER - amzn.to/2TIkUqK
CTS HOSE KIT - amzn.to/3FCLXIL
MAKITA HOOVER - amzn.to/3cvNl3p
MAKITA CHOP SAW / MITRE SAW (LS1019L) - amzn.to/330BcCF
SCISSOR LIFT/CHOP SAW LIFT - amzn.to/3goeaI
MAKITA ROUTER TRIMMER( MUST HAVE!!! ) - amzn.to/3JNENDp
1/4" FLUTE CUTTER
1.6MM RADIUS - MICRO ROUND CUTTER FOR 1/4" ROUTER TRIMMER - amzn.to/3cTCYW6
JIGSAW - amzn.to/2R9z7em
POWER DRILL - amzn.to/2V2SGWT
MAKITA BELT SANDER - amzn.to/2UWDudW
BOSCH CHOP/MITRE SAW - amzn.to/3dUmyxl
MAKITA BRAD NAILER - amzn.to/2YOuiK0
MITRE FAST SPRAY GLUE - amzn.to/34pvYem
35MM HINGE CUTTER - amzn.to/2POJR09
SIP 10" TABLE SAW - amzn.to/2udA4JU
250mm TREND 48T BLADE - amzn.to/3aq2pgI
KETER FOLDING WORKBENCH (THIS IS A MUST BUY) - amzn.to/2NEWzyk
JOINTING COMPOUND FILLER - amzn.to/30AlVD2
ORBITAL SANDER SANDING DISCS ASSORTED - amzn.to/2FZe1JI
500MM GTV SIDE MOUNTED DRAWER RUNNERS - amzn.to/2sJ6YBU
MAKITA COMBI & IMPACT DRILL SET 18V - amzn.to/37qwNpi - แนวปฏิบัติและการใช้ชีวิต
Excellent video mate! I finally feel sure of myself to go install some of these bloody hinges 🙂
Glad to see new generations in the UK are regularly using metric system now
Thank you...
And I'm glad they helped ☺️
Brilliant video Ryan, you help us diyers with our home projects, passing on your experiance and knowledge, thanks a lot.
Thank you!
I'm happy it's helping!
Thanks Ryan
Comprehensive and straightforward, keeping this one for future reference, ta!
That's great 👍👍👍
This is very helpful, I wasn’t sure about the spacing on these concealed hinges however this is very simple and straight forward, thank you
Thank you!
great video man, thank you!
Great! You're welcome
Invaluable information. Thank you sir
Thank you very much!!!
I appreciate it ☺️👍
Cheers Ryan
Great watch pal 👍 🔨
Hello,
I've been binge watching your videos as my sis wants me to have a go of making her an alcove wardrobe, so thanks for all the information you upload.
Regarding concealed hinges and the faker shaker style doors, are your doors 18mm MDF with a 6mm overlay, or 12mm with 6mm overlay. If 12mm, are there any problems caused when drilling the 35mm hinge hole? If 18mm, what hinges do you use to accomodate the 24mm total thickness?
Thanks, good lesson
Thanks 😁
Morning Ryan, another good video thanks. I am going to try using the same make hinge as what you do. I have been fitting these hinges for many years. I have a Kreg jig that does the job ok. Before that I made my own jig as you do. The problem I have is buying these hinges, some makes you buy the back plate separately to the hinge. I find it can get quite confusing, yes I know it’s me. However a refresher on the subject is always handy. Thanks again. Take care.
Hi Jerry, sorry for the late reply
Thank you!
I know what you mean.
I like these hinges and they come as a whole(
(Hinge and plate and covers) .
I also like the large amount of adjustment in them too.
I have the kreg, but when I got the veiko jig I stopped using it.
Cheers ryan
@@thelondoncraftsmanworkshop No worries. Thanks for your reply. Business must come first.
You're welcome, yes it's a bit busy atm.
I hope you are well!
Cheers 👍
Hi, I just started making some bedroom cabinets, I've bought a simple jig but now I'm confused about the hinges I need as there is so much choice on length's of products.... does the same jig fit most lengths?
Very helpful tutorial on full overlay hinge installation
Thank you!
I'm glad it helped 😊
Ryan
Hi Ryan, recently found your channel as im about to embark on the wardrobes and cabinets for our home renovation. You have gave me yhe confidence and information i think to allow me to do a pretty good job. I must ask where you got your square with the holes from?
Thanks again buddy
Apologies, I think I got this one from amazon, I like the fact they have the holes in 1mm increments.
I cant find the exact one but type in woodworking square and you should find one similar 👍
And good luck by the way, I'm glad the vids can be of some use 😊
Hi,
I’ve got the same cutter after watching your videos…I’ve noticed you don’t twist lock your cutting guide into place. Not sure if you know that or not but it helps reduce any play.
Thanks for the vids…they really help me out!
Hi, I didnt know you could do that. I looked at it and I can't see how that works, maybe it's a different model?
Hi ryan ,say for example you make a 600mm by 600mm mdf cabinet would you just take off 3mm from each side of the door or is there a specific size your door has to be smaller than the unit.?
Hi Marty sorry for the delay!
Well if there is no panel or other door going either side of 'said' door, then no gap is needed on the sides.
If it was one door sitting over/in front of a carass and the trims were stepped back (flush with carcass) then the door would be the same width as the carcass.
Hopefully I understood your question correctly.
cheers
Ryan
hi ryan, i was wondering if you predrilled holes into the face of the frame and if not why not? I am a beginner
Hi, I generally don't predrill them, it gives the screws a better bite.
They can be prefilled but only a small amount and with a 2 mm drill bit. But it's not essential
Great video mate, i have the same jig and amazingly after a while the 2mm hole guide no longer line up, so its funny you mentioned it 😅
Thank you mate!
Yes it's strange isn't it unless gtv have changed the spacings?
@@thelondoncraftsmanworkshop i only use Blum so not sure what has gone wrong 🙂
Yep who knows 🤣🤣 maybe can predrill new holes in that part of the jig 🤔
Hi Ryan - where do you buy the GTV hardware from? Thanks 👍🏻
Hi I have put a link in the description just now for you :-)
Nice video Ryan, my only comment would be that 99% of the time, you’d fit a door after the cabinet is built without the luxury of having the pieces lying side by side. Would have been better to see this. How much adjustment are there in the hinges?
It's all I had in the workshop at the time 👍
Hello Ryan. Well done. Do you have a link for the little red marking square you used for the 37mm line on the frame?
Hi sorry for the late reply, did you manage to find it?
@@thelondoncraftsmanworkshop I did thanks, on Amazon
Could you share a link as I would quite like to get one as well
how are you getting the 37mm #, from edge, for the placement of the baseplates?
I close the hinge, make it square, and measure from the centre of the fixing holes to where the door would start 👍
Good tutorial. I need to replace a Grass brand hinge that keeps unclipping. Looking at the catalogue is so confusing with all the different measurements. It seems like there is no direct replacement, so I hope they are somewhat compatible.
As long as you use the same type as you have, you should be able to use another brand or a newer type grass hinge.
If in doubt, change all the hinges on that door, so they work in sync with each other, this should eliminate any doubt 👍
can you please tell me where you got that square marking guide from
Thank you
Hi these arnet the exact ones but this is where I got them from
www.banggood.com/custlink/DDKZ3fOekQ
another great video - just a side note , there is a difference between an awl and bradawl , in the tip , i have both - the bradawl should have a chisel type flattened end. I used to always have bradawl, only recently got my self a couple of awls
I collect awls
Haha yes, I know that now 🤣 I called it a bradawl for years lol
is it always 100mm from edges of the door no matter what size the door is?? Eg. big or small
Well the top and bottom hing I always do 100mm, then divide up the rest equally.
I full size door say 2400mm x 600mm would generally have 4 hinges, or 5 if you wanted to be sure to be sure...cheers Ryan
What tool did you use to get the precise depth of the plate?
Im not really sure I understand the question
Great but marking is a bit trickier when the cabinet is already built.
It is a bit trickier, but doable with the right technique :-)
What size are the hinges , I get confused with the sizes advertised 64, 110, 115 etc
Most common are 110 degrees, these are also 110 👍👍
How do you know the distance from the edge ,, you are setting at 4 mm ...do different hinges req different distances ? How do you know ? Cheers
Can someone answer this question pls 🙏
Well when you buy hinges such as blum or hafele brands, they can come with different thickness mounting plates (the part that gets fixed to the carcass , not door). So there are variations according to what door gaps you are looking to achieve.
My general rule of thumb for the hinges I use(although they don't come with instructions) is a 4mm gap from the edge of thr door to the start of the 35mm Diameter hinge hole.
This is what I usually start with and to be fair, 99% of the time is good for all 35mm hinges.
You can always look up the specs of the hinge that you are using online, I'm sure you would find that measurement.
Ryan
how do you know from the edge of the door carcass that it's 37mm? or are they all that?
Most of them are like that.
You can put hibg on door, then put door up against carcass at a 90 degree to it, close the hinge so the plate part is touching the carcass and then measure from the front of carcass to centre of fixing holes.
Make sure you put 3mm spacer in between door and carcass and that your plate on the hinge has been adjusted to center.
cheers legend!
@@thelondoncraftsmanworkshop
Doing great thanks how are you?
Hello mate I'm good thanks!
When are starting your channel?
@@thelondoncraftsmanworkshop yeah I need to upload some more videos. I cleared my garage but now it's messy again lol
How do you fit 22mm doors to be overlay?
Same technique, just make sure the hiniges you use allow for doors thicker than 18mm
If door heights 1000mm(h) x 300mm(w) how many hinges need it?
2 will easily do the trick. But 3 if you want to, but not needed though.
@@thelondoncraftsmanworkshop thanks Mate
You're welcome 👍
How do you know if you need 3mm,4mm,5mm or 6mm? And how did you know it was 37mm high on the frame?
Hi I just worked it out, the 6mm works for me, 3mm is a little too tight.
Close the hinge and place the door against frame along with a 3mm gap in between. That should give 37mm (if the hinge has been adjusted to centre)
👍
@thelondoncraftsman2026 just want to say thanks for making the video and kindly responding. Super appreciated.
Do you have a link to the hinges??😊
Oh yes I forgot to add the link. I'll put up and let you know asap 👍
@@thelondoncraftsmanworkshop absolutely love your videos and your work. Got it all nailed down to a tee. Definitely setting the bench mark
Thank you mate, I really appreciate that! 👍👍
I've also put a link to the hinges in the description just now too. 👍🙂
£37 for one hinge!
How do you mean, should be around £1.5 -£2 a hinge
Its for 30 hinges